u32 filter
Hello!
What is the significance of "handle" in a u32 filter??
For example, if I have a HTB class 1:1 and three child classes 1:11, 1:12, and 1:13. Within 1:11, I define dsmark, say 2:0, and let it mark packets with certain DSCP. Now, using the u32 filter I need to classify packets of a certain flow (e.g., based on src ip address and dest port), then can someone give me an example of exactly how the u32 filter would look.
The following configuration does not seem to work (i.e., packets are not getting marked!)...so I guess the problem is with my u32 filter
tc filter add dev eth0 parent 1:0 protocol ip prio 1 handle 1: \
u32 divisor 1
tc filter add dev eth0 parent 1:1 prio 1 u32 \ match ip src 192.168.1.12 match ip protocol 17 0xff match ip dport 4984 0xffff flowid 2:0
Any help in this matter is greatly appreciated.
Thank you
regards
Kaustubh
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hi all.
I have the following queue:
tc qdisc add dev eth0 root handle 1:0 htb default 15
tc class add dev eth0 parent 1:0 classid 1:1 htb rate 100mbit ceil 100mbit
tc class add dev eth0 parent 1:1 classid 1:7 htb rate 64kbit ceil 64kbit tc class add dev eth0 parent 1:1 classid 1:15 htb rate 102336kbit ceil 100mbit
tc qdisc add dev eth0 parent 1:7 handle 10:0 sfq perturb 10 tc qdisc add dev eth0 parent 1:15 handle 20:0 sfq perturb 10
Now, my question is, the filter should be:
tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip 57.227.234.22 flowid 1:7
or,
tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip 57.227.234.22 flowid 10:0
?
What about the default?
Thankx,
-vcf
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Looking at the LARTC document on page 65, the sample htb configuration, it should be the first one.
cheers
yuan
Quoted 29 lines · Vitor Carlos Flausino
Hi all.
I have the following queue:
tc qdisc add dev eth0 root handle 1:0 htb default 15
tc class add dev eth0 parent 1:0 classid 1:1 htb rate 100mbit ceil 100mbit
tc class add dev eth0 parent 1:1 classid 1:7 htb rate 64kbit ceil 64kbit tc class add dev eth0 parent 1:1 classid 1:15 htb rate 102336kbit ceil 100mbit
tc qdisc add dev eth0 parent 1:7 handle 10:0 sfq perturb 10 tc qdisc add dev eth0 parent 1:15 handle 20:0 sfq perturb 10
Now, my question is, the filter should be:
tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip 57.227.234.22 flowid 1:7
or,
tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip 57.227.234.22 flowid 10:0
?
Quoted 8 lines
What about the default?
Thankx,
-vcf_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 22 lines · Vitor Carlos Flausino
Hi all.
I have the following queue:
tc qdisc add dev eth0 root handle 1:0 htb default 15
tc class add dev eth0 parent 1:0 classid 1:1 htb rate 100mbit ceil 100mbit
tc class add dev eth0 parent 1:1 classid 1:7 htb rate 64kbit ceil 64kbit tc class add dev eth0 parent 1:1 classid 1:15 htb rate 102336kbit ceil 100mbit
tc qdisc add dev eth0 parent 1:7 handle 10:0 sfq perturb 10 tc qdisc add dev eth0 parent 1:15 handle 20:0 sfq perturb 10
Now, my question is, the filter should be:
tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip 57.227.234.22 flowid 1:7
Quoted 8 lines
or,
tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip 57.227.234.22 flowid 10:0
?
What about the default?
The default is the minor number, so the second number in 1:15. So 15 like you did.
For the filter, 10:0 is connected to 1:7. So all traffic placed in 1:7 flows through 10:0. So the filter should point to 1:7. So the first filter rule is the one you need.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
is there any command to see how my u32 filters have been applyed? in case not, i should use iptables & fwmarks right? thanks and greets
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
tc -s filter ls dev eth0 or whatever device you are using
you can also check out the qdiscs and classes. The classes actually tell you how much bandwidth has passed, which is pretty handy.
tc -s qdisc ls dev...
tc -s class ls dev...
-----Original Message-----
From: Esteban [mailto:[email protected]]
Sent: Friday, May 23, 2003 5:58 AM
To: Lartc
Subject: [LARTC] u32 filter
is there any command to see how my u32 filters have been applyed? in case not, i should use iptables & fwmarks right? thanks and greets
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/