Skip to contentSkip to conversation

SLA/Shaping Question

LARTC Jake Stride 1 participant 1 message Dec 10, 2002

lore
Share & tools
lore
#0 lore raw

Hi, I have a basic router that is shaping traffic, and it seems to be working at the moment.

We have a 100Mbit connection to the internet, however we get charged for each mbit that we use and so have to shape/limit the traffic to avoid huge bills and my boss getting cross!!

We have a /29 subnets set up as follows:

tc qdisc add dev eth0 root tbf rate 0.8Mbit latency 50ms burst 10k

tc qdisc add dev eth1 root tbf rate 0.6Mbit latency 50ms burst 10k

                       |--------------|
Internet (100Mbit)     |              | eth1      |---------| 
                 ------  Linux router   ----------  Switch  |
eth0                   |              | .105      |---------|
                       |--------------| .106            |
                                        .107          .108
                                                      .109
                                                      .110

This setup seems to limit the traffic to ~1mbit to the internet at the moment.

Basically I have a linux box with a few backup dns and mail servers on them (hence eth1 has 3 ips) and then 3 servers attached to a 100mbit switch, each with it's own IP and full access.

However I now need to add a new server(s) to the switch on a different /29 subnet. I want to ensure thaHi, I have a basic router that is shaping traffic, and it seems to be
working at the moment.

We have a 100Mbit connection to the internet, however we get charged for each mbit that we use and so have to shape/limit the traffic to avoid huge bills!!

We have a /29 subnets set up as follows:

tc qdisc add dev eth0 root tbf rate 0.8Mbit latency 50ms burst 10k

tc qdisc add dev eth1 root tbf rate 0.6Mbit latency 50ms burst 10k

                       |--------------|
Internet (100Mbit)     |              | eth1      |---------| 
                 ------  Linux router   ----------  Switch  |
eth0                   |              | .105      |---------|
                       |--------------| .106            |
                                        .107          .108
                                                      .109
                                                      .110

This setup seems to limit the traffic to ~1mbit to the internet at the moment.

Basically I have a linux box with a few backup dns and mail servers on them (hence eth1 has 3 ips) and then 3 servers attached to a 100mbit switch, each with it's own IP and full access.

However I now need to add a new server(s) to the switch on a different /29 subnet. I want to ensure that the current .105/29 subnet continues to receive 1mbit up and down and each server on the new subnet each receives an individual 1mbit:

.105/29 - 1Mbit

New subnet .120/24 - 6Mbit Total

.120 - 1Mbit
.121 - 1Mbit
.122 - 1Mbit
.123 - 1Mbit
.124 - 1Mbit
.125 - 1Mbit

I want to ensure that the traffic out on eth0 is never more than 7Mbit but the .105/24 subnet never users more than 1Mbit and the .120/29 subnet gets 6Mbit and each server on the .120/29 gets a min of 1Mbit but can burst upto 6Mbit if the other servers are idle and that all traffic over the switch can move at 100Mbit between each host. Ideally I don't want more than 7Mbit coming in on eth0 either.

Also is it possible to ensure that ssh traffic gets some priority so that access isn't too slow?

Is this possible? I was looking into the SLA section of the docs but wasn't entirely sure how to go about this.

Thanks

Jake
t the current .105/29 subnet continues
to receive 1mbit up and down and each server on the new subnet each receives an individual 1mbit:

.105/29 - 1Mbit

New subnet .120/24 - 6Mbit Total

.120 - 1Mbit
.121 - 1Mbit
.122 - 1Mbit
.123 - 1Mbit
.124 - 1Mbit
.125 - 1Mbit

I want to ensure that the traffic out on eth0 is never more than 7Mbit but the .105/24 subnet never users more than 1Mbit but the .120/29 subnet gets 6Mbit and each server gets a min of 1Mbit but can burst upto 6Mbit if the other servers are idle and that all traffic over the switch can move at 100Mbit between each host. Ideally I don't want more than 7Mbit coming in on eth0 either

Is this possible? I was looking into the SLA section of the docs but wasn't entirely sure how to go about this.

Thanks

Jake

Signature · 5 lines
Jake Stride <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/