Skip to contentSkip to conversation

tc htb stats

LARTC David DeLauro 3 participants 4 messages Feb 4, 2003

lore
Share & tools
lore
#0 lore raw

I have an htb qdisc setup and it is shaping my traffic wonderfully but I've just recently started taking a look at the output from the command

tc -s class ls dev eth?

Looking at the "rate" line I thought to myself..."cool I can use this to graph throughput avg.es without having to worry about the "Sent bytes" rolling over or being lost when the htb qdisc is recreated" _BUT_ it seems the rates are inaccurate. When I look at the rate my cisco router reports for a 5min avg and I look at a calculated 5min average (30 polls of the tc once every 10sec) for tc they are very different. The cisco is reported as ~2090kb/s and tc reports my parent as ~251kb/s. Even if I take all the classes separately and add the averages together I get closer but not that much closer. Is my math wrong? How does the tc/htb qdisc figure the avg. rate?

Signature · 11 lines
David DeLauro

Talk sense to a fool and he calls you foolish. - Euripides

Those who do not think about their own sins make up for it by thinking incessantly about the sins of others. - C. S. Lewis  (God in the Dock, "Miserable Offenders," p. 124)

Never undertake anything for which you wouldn't have the courage to ask the blessing of heaven. - G. C. Lichtenberg (1742-1799)

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw

David,

: When I look at the rate my cisco router
: reports for a 5min avg and I look at a calculated 5min average (30 polls : of the tc once every 10sec) for tc they are very different. The cisco is : reported as ~2090kb/s and tc reports my parent as ~251kb/s.

: Even if I take all the classes separately and add the averages together : I get closer but not that much closer. Is my math wrong? How does the : tc/htb qdisc figure the avg. rate?

$ expr 251 \* 8
2008

Snipped from http://www.docum.org/stef.coene/qos/docs/ :

"When you use the tc command, you have to remember that mb = 1024 kb 1024 * 1024 b = byte/s and that mbit = 1024 kbit = 1024 * 1024 bit bit/s."

Snipped from http://lartc.org/howto/lartc.qdisc.html :

"Just to prevent confusion, tc uses the following rules for bandwith
specification:

mbps = 1024 kbps = 1024 * 1024 bps => byte/s
mbit = 1024 kbit => kilo bit/s.
mb = 1024 kb = 1024 * 1024 b => byte
mbit = 1024 kbit => kilo bit.!

Are you certain your units are the same? Strangely, the tc command line tool uses kb for kilobytes/second. I think 251 kilobytes-per-second is quite close to 2090 kilobits-per-second.

Bye for now,

-Martin

Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to David DeLauro

On Tue, 4 Feb 2003 At 10:20 -0600, [email protected] Articulated:

Quoted 7 lines

Snipped from http://lartc.org/howto/lartc.qdisc.html :

"Just to prevent confusion, tc uses the following rules for bandwith
specification:

   mbps = 1024 kbps = 1024 * 1024 bps => byte/s

Thanks Martin...

I was running under the assuption that "bps" was bits/s and "Bps" was bytes/sec...

peace

Signature · 11 lines
David DeLauro

Hata ukinichukia la kweli nitakwambia - Kanga Proverb

Apart from God every activity is merely a passing whiff of insignificance. -  Alfred North Whitehead (1861-1947)

Never undertake anything for which you wouldn't have the courage to ask the blessing of heaven. - G. C. Lichtenberg (1742-1799)

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to David DeLauro
Quoted 6 lines · David DeLauro

On Tue, 4 Feb 2003 At 10:20 -0600, [email protected] Articulated:

Quoted 5 lines

Snipped from http://lartc.org/howto/lartc.qdisc.html :

"Just to prevent confusion, tc uses the following rules for bandwith
specification:

Quoted 6 lines
Quoted 1 line
   mbps = 1024 kbps = 1024 * 1024 bps => byte/s

Thanks Martin...

I was running under the assuption that "bps" was bits/s and "Bps" was bytes/sec...

It's bit when there is bit, otherwise it's byte :)

Stef

Signature · 9 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/