Skip to contentSkip to conversation

quantum value for voip

LARTC Victor Cassar 3 participants 10 messages Feb 12, 2003 – Feb 17, 2003

lore
Share & tools
lore
#0 lore raw

Well

I understand why quantum should be at least equal to mtu size

but let´s think in this

if i have a dsl link and i want to give more quality to
"one voip user"
i´ve already solved the dsl upload problem transfering the bottleneck to my shapping box.

Should i change the quantum to a lower value for that class?

any ideas or comments about this?

Thanks in advance

__________________________________________________
Do you Yahoo!?
Yahoo! Shopping - Send Flowers for Valentine's Day
http://shopping.yahoo.com
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 13 lines · Victor Cassar

Well

I understand why quantum should be at least equal to mtu size

but let´s think in this

if i have a dsl link and i want to give more quality to
"one voip user"
i´ve already solved the dsl upload problem transfering the bottleneck to my shapping box.

Quoted 4 lines

Should i change the quantum to a lower value for that class?

any ideas or comments about this?

Do you know where quantum is used for? It's for classes that are asking for remaining bandwidth. So if that "one voip user" is never asking for more then the configured rate of its class, quantum is never used. So it really depends on how you configured the classes to answer that question.

And taking a quantum of 10 byte is not "wrong". But if you send 1000byte and your quantum is 10byte, htb will use 10byte in it's calculations. So it can disturb the setup, but nothing bad will happen.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Victor Cassar

Thanks Stef

Yep i missunderstood the quantum concept (it´s clear now), but since my voip class was configured with enough bw this doesn´t matter

Reading more on docum.org, i find hte possible cause of the delays i was using sfq (128p queue) on the leaf i removed sfq from the voip class

I will try also with other disciplines.. like tbf just to have a deeper understanding of queuing in real life applications

Are there any recomendation on which queuing discipline to use with voip?
(my stats show 100 bytes per packet average in voip)

i´m doing more tests now and i´ll re re-read the full lartc. doc

regards

Quoted 32 lines · --- Stef Coene
Quoted 3 lines · Victor Cassar

Well

I understand why quantum should be at least equal

to

Quoted 5 lines

mtu size

but let´s think in this

if i have a dsl link and i want to give more

quality

Quoted 3 lines

to
"one voip user"
i´ve already solved the dsl upload problem

transfering

Quoted 3 lines

the bottleneck to my shapping box.

Should i change the quantum to a lower value for

that

Quoted 3 lines

class?

any ideas or comments about this?

Do you know where quantum is used for? It's for classes that are asking for
remaining bandwidth. So if that "one voip user" is never asking for more
then the configured rate of its class, quantum is never used. So it really
depends on how you configured the classes to answer that question.

Quoted 18 lines

And taking a quantum of 10 byte is not "wrong". But if you send 1000byte and
your quantum is 10byte, htb will use 10byte in it's calculations. So it can
disturb the setup, but nothing bad will happen.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

http://lartc.org/

__________________________________________________
Do you Yahoo!?
Yahoo! Shopping - Send Flowers for Valentine's Day
http://shopping.yahoo.com
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Victor Cassar
Quoted 6 lines · Victor Cassar

Thanks Stef

Yep i missunderstood the quantum concept (it´s clear now), but since my voip class was configured with enough bw this doesn´t matter

Quoted 7 lines

Reading more on docum.org, i find hte possible cause of the delays i was using sfq (128p queue) on the leaf i removed sfq from the voip class

I will try also with other disciplines.. like tbf just to have a deeper understanding of queuing in real life applications

Tbf will not change nything. Htb is acutally a tbf but with classes.

Quoted 3 lines

Are there any recomendation on which queuing discipline to use with voip?
(my stats show 100 bytes per packet average in voip)

Why not a simple fifo? You can adapt the size of it from the command line.

Quoted 2 lines

i´m doing more tests now and i´ll re re-read the full lartc. doc

Keep us informed.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#5 lore raw
In reply to Victor Cassar

Sorry, I sent it in HTML the first time. Here it is again in text format.

To minimize latency, (which is probably what you want for voip traffic), give the class a high priority.
Make sure it never reaches its configured rate. If it does, you will see that the latency increases.
If you think it might reach its configured rate, than use a policing filter before the class to place an upper limit on the rate. And, as Steph memtionned, a FIFO is a good thing. Just make sure it is big enough to handle your expected burst, but not too big because it could
increase the latency.

Good luck,
Mathieu.

Quoted 11 lines

Yep i missunderstood the quantum concept (it´s clear now), but since my voip class was configured with enough bw this doesn´t matter

Reading more on docum.org, i find hte possible cause of the delays i was using sfq (128p queue) on the leaf i removed sfq from the voip class

I will try also with other disciplines.. like tbf just to have a deeper understanding of queuing in real life applications

Tbf will not change nything. Htb is acutally a tbf but with classes.

Quoted 3 lines

Are there any recomendation on which queuing discipline to use with voip?
(my stats show 100 bytes per packet average in voip)

Why not a simple fifo? You can adapt the size of it from the command
line.

Quoted 2 lines

i´m doing more tests now and i´ll re re-read the full lartc. doc

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#6 lore raw
In reply to Victor Cassar
Quoted 9 lines · Mathieu Deziel

Sorry, I sent it in HTML the first time. Here it is again in text format.

To minimize latency, (which is probably what you want for voip traffic), give the class a high priority.
Make sure it never reaches its configured rate. If it does, you will see that the latency increases.
If you think it might reach its configured rate, than use a policing filter before the class to place an upper limit on the rate.

I once suggested that as a solution, but has anyone tested it?

Quoted 1 line

And, as Steph

:)

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#8 lore raw
In reply to Victor Cassar

1st thanks Stef and Mathieu

Quoted 2 lines · wrote:

Why not a simple fifo? You can adapt the size of it from the command line.

I want tu use this pfifo queue i know its hardwired and that i need to mark packets here or from the source
in order to use dscp field

but i need some small sample to try

i cant figure out how to use this to divide traffic in those 3 bands , or diferent rates

I´m analizing some sample scripts i took from the mail archive, but i still need some hints,

Do i need to use dsmark qdisc?

I greatly apreciate some samples from some one here basicaly i need to divide traffic in 2 types voice & and data, i already have a voip device with diffserv capability,

Another important thing is that i´m using
bridge+netfilter, so i´m not routing,

regards & happy weekend
Victor

__________________________________________________
Do you Yahoo!?
Yahoo! Shopping - Send Flowers for Valentine's Day
http://shopping.yahoo.com
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#9 lore raw
In reply to Victor Cassar

Hi Victor, see below.

Quoted 9 lines
Quoted 3 lines

Why not a simple fifo? You can adapt the size of it from the command line.

I want tu use this pfifo queue i know its hardwired and that i need to mark packets here or from the source
in order to use dscp field

The pfifo and bfifo qdiscs are not "hardwired". Their size is configurable (specified in bytes for the bfifo, and in number of packets for the pfifo). The one that is hardwired is the pfifo_fast: it is the default qdisc, the one that is there when you don't configure anything. The pfifo_fast has 3 internal prio queues. Packets are classified in one of the three prio queue according to the dscp mark, just like you said in you previous mail. Yes, to make use of the priority capability of pfifo_fast, your packets must marked before they enter the tc software. You can use iptables to mark the packets before they enter tc.

Another thing you can do it make use of the prio qdisc, and then create your own (u32) filters. You can then mark the packets with dsmark before the packets go out, if you want.

Hope this helps,
Mathieu.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/