Skip to contentSkip to conversation

Suggestions welcome

LARTC Jeff Nye 2 participants 2 messages Feb 20, 2003

lore
Share & tools
lore

Jeff Nye

author
#0 lore raw

I have a network laid out as follows.

The Network

---------- Eth0 - INTERNET x.x.x.x

 LINUX   |
Router1  | Eth2 - LAN   172.16.1.x
         |
---------- Eth1 -Bridge 1a  192.168.1.1
    |
    |
---------- Eth0 - Bridge 1b  192.168.1.2
 LINUX   |
Router2  | Eth2 - LAN   172.16.2.x
         |
---------- Eth1 -Bridge 2a 192.168.2.1
    |
    |
---------- Eth0 - Bridge 2b  192.168.2.2
 LINUX   |
Router3  | Eth2 - LAN1   172.16.3.x
         | Eth3 - LAN2   172.16.4.x
         | Eth4 - LAN3   172.16.5.x
         |
---------- Eth1 -Bridge 3a 192.168.3.1
    |
    |
---------- Eth0 - Bridge 3b  192.168.3.2
 LINUX   |
Router4  | Eth1 - INTERNET 2   x.x.x.x
         |
---------- Eth2 - Bridge 4a  192.168.4.1
    |
    |
---------- Eth0 - Bridge 4b  192.168.4.2
 LINUX   |
Router5  | Eth1 - LAN   172.16.2.x
         |

----------

Currently I do no real routing and use mainly IPTABLES to set rules for forwarding. This worked great until I got a second source, Now I set up virtual interfaces for each person I want to go out INTERNET 2 or eth1 on router 4.

I want to use a routing protocol that will allow these routers to speak to each other. I wanted to get feedback on where I could find some GOOD documentation on OSPF or RIPv2.

There are large amounts of computers on each LAN and I want the router to determine which line is the best to send the packet out. I would also like the ability to tell it only send certain types of clients out one pipe. Does anyone have suggestions for this. I would like to keep it a little more low maintenance then my firewall scripts I already have. By the way I have swizeet HTB limiting scripts I hope to contribute to the list.

Thanks,

==/* Jeff Nye */
/* 801-728-1755 */

__________________________________________________
Do you Yahoo!?
Yahoo! Tax Center - forms, calculators, tips, more
http://taxes.yahoo.com/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

On 20-02-2003 at 08:39:32AM -0800, Jeff Nye wrote:
JN> I have a network laid out as follows. JN>
JN> The Network
JN>
JN>
JN> ---------- Eth0 - INTERNET x.x.x.x

JN>  LINUX   |
JN> Router1  | Eth2 - LAN   172.16.1.x
JN>          |

JN> ---------- Eth1 -Bridge 1a 192.168.1.1
JN> |
JN> |
JN> ---------- Eth0 - Bridge 1b 192.168.1.2

JN>  LINUX   |
JN> Router2  | Eth2 - LAN   172.16.2.x
JN>          |

JN> ---------- Eth1 -Bridge 2a 192.168.2.1
JN> |
JN> |
JN> ---------- Eth0 - Bridge 2b 192.168.2.2

JN>  LINUX   |
JN> Router3  | Eth2 - LAN1   172.16.3.x
JN>          | Eth3 - LAN2   172.16.4.x
JN>          | Eth4 - LAN3   172.16.5.x
JN>          |

JN> ---------- Eth1 -Bridge 3a 192.168.3.1
JN> |
JN> |
JN> ---------- Eth0 - Bridge 3b 192.168.3.2

JN>  LINUX   |
JN> Router4  | Eth1 - INTERNET 2   x.x.x.x
JN>          |

JN> ---------- Eth2 - Bridge 4a 192.168.4.1
JN> |
JN> |
JN> ---------- Eth0 - Bridge 4b 192.168.4.2

JN>  LINUX   |
JN> Router5  | Eth1 - LAN   172.16.2.x
JN>          |

JN> ----------
JN>
JN> Currently I do no real routing and use mainly IPTABLES to set rules for forwarding. This JN> worked great until I got a second source, Now I set up virtual interfaces for each person JN> I want to go out INTERNET 2 or eth1 on router 4.
JN>
JN> I want to use a routing protocol that will allow these routers to speak to each other. I JN> wanted to get feedback on where I could find some GOOD documentation on OSPF or RIPv2.

http://lartc.org/lartc.pdf
Chapter 17
or http://www.zebra.org

Only about OSPF, BGP and protocols: http://www.cisco.com or rfc's :)

JN>
JN> There are large amounts of computers on each LAN and I want the router to determine which JN> line is the best to send the packet out. I would also like the ability to tell it only

spray, mgen

JN> send certain types of clients out one pipe. Does anyone have suggestions for this. I

man iptables /MARK

JN> would like to keep it a little more low maintenance then my firewall scripts I already JN> have. By the way I have swizeet HTB limiting scripts I hope to contribute to the list. JN>
JN> Thanks,
JN>

Rgds,
Bartek.
--

GPG-key-ID:  0x948DE45D -- visit http://www.keyserver.net
Fingerprint: 95E9 8E2D 1801 7864 2244  6EAA 03E5 764D 948D E45D

The great baby you see there is not yet out of his swaddling-clouts.
Shakespeare, Hamlet.