Classless Queues in series...
I need (or would at lest live very much :) to use two Classless Queues in series.
I can't see in the HOWTO how this is done, but guess at something like:
tc qdisc add dev eth0 root handle 1: sfq (etc)
tc qdisk add dev eth0 parent 1: tbf (etc)
Am I on the right lines here?
I also have a small problem with TBF... From the HOWTO sec 9.2.2, it is surgested that a value for the 'burst' should be:
"For 10mbit/s on Intel, you need at least 10kbyte buffer if you want to reach your configured rate!"
Therefore: burst => rate * (8 / 1000)
However, I find using this I get stall on ftp and other common protocols, when they get above the throttle rate, with low bandwidths (eg, 64kbit/sec). -- Or I completelly fail to understand the above statement...
Does any person have a better method for calculating a good value for 'buffer' ?
Regards, Ben.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Ben,
: I need (or would at lest live very much :) to use two Classless Queues : in series.
:
: I can't see in the HOWTO how this is done, but guess at something like:
:
: tc qdisc add dev eth0 root handle 1: sfq (etc)
: tc qdisk add dev eth0 parent 1: tbf (etc)
:
: Am I on the right lines here?
A classless queueing discipline cannot contain another queueing discipline.
A classful queueing discipline can contain classes and leaf queueing disciplines.
In other words:
- a classless queueing discipline is by definition, a terminal qdisc
- a classful queueing discipline can be terminal or
- can contain a class, which can be terminal or
- can contain another queueing discipline
Does that help?
: I also have a small problem with TBF... From the HOWTO sec 9.2.2, it is : surgested that a value for the 'burst' should be:
:
: "For 10mbit/s on Intel, you need at least 10kbyte buffer if you want to : reach your configured rate!"
:
: Therefore: burst => rate * (8 / 1000)
:
: However, I find using this I get stall on ftp and other common : protocols, when they get above the throttle rate, with low bandwidths : (eg, 64kbit/sec). -- Or I completelly fail to understand the above : statement...
:
: Does any person have a better method for calculating a good value for : 'buffer' ?
I'm afraid I can't help you on this question.
-Martin
Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected] _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 9 lines · Ben Clewett
I need (or would at lest live very much :) to use two Classless Queues in series.
I can't see in the HOWTO how this is done, but guess at something like:
tc qdisc add dev eth0 root handle 1: sfq (etc)
tc qdisk add dev eth0 parent 1: tbf (etc)Am I on the right lines here?
Not really. Like Martin said, some qdiscs can contain classes (htb/cbq). You can add a second qdisc on that classes. In fact, each leaf class contains a qdisc. By default this is a pfifo qdisc, but you can replace it with a classfull qdisc. And you can add a third qdisc to the classes of that second qdisc and so on.
But each qdisc introduces a new queue so extra delays.
Quoted 6 lines
I also have a small problem with TBF... From the HOWTO sec 9.2.2, it is surgested that a value for the 'burst' should be:
"For 10mbit/s on Intel, you need at least 10kbyte buffer if you want to reach your configured rate!"
Quoted 6 lines
Therefore: burst => rate * (8 / 1000)
However, I find using this I get stall on ftp and other common protocols, when they get above the throttle rate, with low bandwidths (eg, 64kbit/sec). -- Or I completelly fail to understand the above statement...
The minimal burst is the amount of packets you can check between 2 updates. And this depends on the internal clock used by the kernel. Say this clock checks the rate each 1/10 second. And you have a rate of 1mbit/s. Then you need a minimal burst of 0.1mbit. If your burst is lower, say 0.05mbit, you only can send 0.05mbit each time your timer checks the tbf so you have a rate of 0.5mbit/s.
Quoted 2 lines
Does any person have a better method for calculating a good value for 'buffer' ?
No. But the bigger the buffer, the more time a packet can stay in the bufffer so the deay can go up.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/