Skip to contentSkip to conversation

ABout Routing..again

LARTC Dhirendra Pal Singh 2 participants 3 messages Mar 12, 2003 – Mar 13, 2003

lore
Share & tools
lore
#0 lore raw

Hi All..
I think the image got screwed up...
I am giving the description again..

Dsl feed goes to gateway 1. Its internal ip address is of 192.168.1.XXX. Now from here goes the feed to another gateway which eth0 ip address is 192,168.1.50. It has 2 more eth - eth1 and eth2. Their ip address are 192.168.2.51 and 192.168.3.XXX respectively.
Now my problem is that all the computers connect to 192.168.2.XXX are unable to point to the computers of 192.168.1.XXX. Though strangely I can ping to 192.168.1.1 wich is the internal ip address of the gateway 1.

Can someone help me whith this configuration...?
rest question are below..
Thanks in advance ..
dp

Quoted 44 lines · Dhirendra Pal Singh

Hi All,
I have the following setup on redhat linux 8.0 ...

eth 0
192.168.1.50

                                                                   \
                    |--------------|                              \ 
|--------------|
-----------------| gateway 1|-------------------------|gateway2  |
                   /|_______   |\                               
|--------------|
                 /                      \                             
/                  \
           eth0                   eth1 -                       
/                       \
       61.X.X.X          192.168.1.1              eth1                
   eth2
     (public)                         |                
192.168.2.51        192.168.3.52
                                           |                          
                           |
                                   ------------                       
                       |
                                   |  BOX 1   
|                                 
----------------                                  
                                   -------------                     
             |   Box                                                 
                                            BOX 3      |
                                192.168.1.101                          
      ---------------
                                                                      
               192.168.3.101

My Problem is

A) I am unable to ping from Box 3 (192.168.3.101) to Box 1. Any comments or reasons why?
B) I have figured out that if I enable Masquerading then problem A is solved. Can someone explain why?
C) Is it possible without Masquerading ?

I am in a fix and any Help would be very much appreciated...??

Quoted 10 lines

Thanks and Regards
Dp

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Dhirendra,

: Dsl feed goes to gateway 1. Its internal ip address is of 192.168.1.XXX. : Now from here goes the feed to another gateway which eth0 ip address is : 192,168.1.50. It has 2 more eth - eth1 and eth2. Their ip address are : 192.168.2.51 and 192.168.3.XXX respectively.
: Now my problem is that all the computers connect to 192.168.2.XXX are : unable to point to the computers of 192.168.1.XXX. Though strangely I : can ping to 192.168.1.1 wich is the internal ip address of the gateway 1.

Is this your network, or did I mangle it in reconstruction?

                                          eth0
                                        192.168.1.50
                                               \
           |----------|                         |----------|
           | gateway 1|-------------------------| gateway2 |
          /|__________|\          |             |----------|
         /              \         |             /         \
      eth0             eth1       |            /           \
  61.X.X.X          192.168.1.1   |          eth1          eth2
(public)                          |       192.168.2.51     192.168.3.52
                                  |                         |
                         ------------                       |
                         |  BOX 1   |                  -------------
                         ------------                  |   Box 3   |
                         192.168.1.101                 -------------
                                                      192.168.3.101

You can ping 192.168.1.1 because it is a locally hosted IP on the default gateway of the machines in the 192.168.2.0/24 network.

: I have the following setup on redhat linux 8.0 ...
:
: A) I am unable to ping from Box 3 (192.168.3.101) to Box 1. Any
: comments or reasons why?

It looks like you have a common routing problem. If you examine the routing tables on gateway 1 and box 1, they are probably missing routes to 192.168.3.0/24 and 192.168.2.0/24 via 192.168.1.50. Host 1 probably has a default route to 192.168.1.1 and gateway 1 certainly doesn't have a default route pointing *into* your network.

<gripe>
This is not really a LAR (and certainly not a TC) question. This is a basic routing question. Let's try to keep these questions off the LARTC list....this is probably better for a forum like comp.os.linux.networking or a LUG.
</gripe>

<helpful-hat>
You may find some of my documentation useful in conceptualizing static routing:

http://linux-ip.net/
http://linux-ip.net/html/ch-routing.html

For others who are following along with questions like this, I would recommend using a network analyzer of some kind to look at the packets on each of the machines involved.

- use tcpdump or ethereal on each affected router and end-host
- generate regular traffic (ping, nc, socat, etc.) while trying to determine where the packets are getting dropped or misrouted
</helpful-hat>

So, Dhirendra:

Remove the masquerading from gateway2

[root@box1]# ip route add 192.168.3.0/24 via 192.168.1.50
[root@box1]# ip route add 192.168.2.0/24 via 192.168.1.50
[user@box3]$ ping -n 192.168.1.101

You should get a response.

[root@box2]# ip route add 192.168.3.0/24 via 192.168.1.50
[root@box2]# ip route add 192.168.2.0/24 via 192.168.1.50

: B) I have figured out that if I enable Masquerading then problem A is
: solved. Can someone explain why?

Because you are changing the source IP on the packets to a 192.168.1.0/24. When you do this, the other hosts in 192.168.1.0/24 have a direct route for reply packets.

: C) Is it possible without Masquerading ?

Yes.

-Martin

Anybody think a LARTC FAQ is a good idea?

Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Dhirendra Pal Singh

Thanks a lot once again Martin.
Yes this is the correct diagra.
Mean while I have agian posted my question with the diagram fixed. Please ignore it.

Got your point Martin about why its not working. I will try it later again. I apologise for posting the wrong question.. and thank once again to Martin for taking the pains to correct the diagram and sending and answer. I was in a fix and didnt knew where to send the question. I paniced.. sorry..

I will take care of this in future..
Thanks
Dp

Quoted 88 lines · Martin A. Brown

Dhirendra,

: Dsl feed goes to gateway 1. Its internal ip address is of 192.168.1.XXX. : Now from here goes the feed to another gateway which eth0 ip address is : 192,168.1.50. It has 2 more eth - eth1 and eth2. Their ip address are : 192.168.2.51 and 192.168.3.XXX respectively.
: Now my problem is that all the computers connect to 192.168.2.XXX are : unable to point to the computers of 192.168.1.XXX. Though strangely I : can ping to 192.168.1.1 wich is the internal ip address of the gateway 1.

Is this your network, or did I mangle it in reconstruction?

                                         eth0
                                       192.168.1.50
                                              \
          |----------|                         |----------|
          | gateway 1|-------------------------| gateway2 |
         /|__________|\          |             |----------|
        /              \         |             /         \
     eth0             eth1       |            /           \
 61.X.X.X          192.168.1.1   |          eth1          eth2
(public)                          |       192.168.2.51     192.168.3.52
                                 |                         |
                        ------------                       |
                        |  BOX 1   |                  -------------
                        ------------                  |   Box 3   |
                        192.168.1.101                 -------------
                                                     192.168.3.101

You can ping 192.168.1.1 because it is a locally hosted IP on the default gateway of the machines in the 192.168.2.0/24 network.

: I have the following setup on redhat linux 8.0 ...
:
: A) I am unable to ping from Box 3 (192.168.3.101) to Box 1. Any
: comments or reasons why?

It looks like you have a common routing problem. If you examine the routing tables on gateway 1 and box 1, they are probably missing routes to 192.168.3.0/24 and 192.168.2.0/24 via 192.168.1.50. Host 1 probably has a default route to 192.168.1.1 and gateway 1 certainly doesn't have a default route pointing *into* your network.

<gripe>
This is not really a LAR (and certainly not a TC) question. This is a basic routing question. Let's try to keep these questions off the LARTC list....this is probably better for a forum like comp.os.linux.networking or a LUG.
</gripe>

<helpful-hat>
You may find some of my documentation useful in conceptualizing static routing:

http://linux-ip.net/
http://linux-ip.net/html/ch-routing.html

For others who are following along with questions like this, I would recommend using a network analyzer of some kind to look at the packets on each of the machines involved.

- use tcpdump or ethereal on each affected router and end-host
- generate regular traffic (ping, nc, socat, etc.) while trying to determine where the packets are getting dropped or misrouted
</helpful-hat>

So, Dhirendra:

Remove the masquerading from gateway2

[root@box1]# ip route add 192.168.3.0/24 via 192.168.1.50
[root@box1]# ip route add 192.168.2.0/24 via 192.168.1.50
[user@box3]$ ping -n 192.168.1.101

You should get a response.

[root@box2]# ip route add 192.168.3.0/24 via 192.168.1.50
[root@box2]# ip route add 192.168.2.0/24 via 192.168.1.50

: B) I have figured out that if I enable Masquerading then problem A is
: solved. Can someone explain why?

Because you are changing the source IP on the packets to a 192.168.1.0/24. When you do this, the other hosts in 192.168.1.0/24 have a direct route for reply packets.

Quoted 10 lines

: C) Is it possible without Masquerading ?

Yes.

-Martin

Anybody think a LARTC FAQ is a good idea?

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/