Skip to contentSkip to conversation

ABout Routing..diag fixed..

LARTC Dhirendra Pal Singh 2 participants 2 messages Mar 13, 2003

lore
Share & tools
lore
#0 lore raw

Thanks to David and Martin,

Okay I am copying the diagram again.. I remade it in acsi and replaced the tabs with space.Have tested it on my box by sending the email to myself and another box. It looks fine..

I hope it dosent breaks this time

                                      eth 0 192.168.1.50
                                                   \
                 |----------|                       \ |--------------|
-----------------| gateway 1|-------------------------|gateway2  |
                /|_______   |\                        |--------------|
               /              \                      /                  \
           eth0             eth1 -                  /                    \
       61.X.X.X          192.168.1.1              eth1                   
eth2
     (public)                 |                192.168.2.51        
192.168.3.52
                              |                                        |
                         ------------                                  |
                         |  BOX 1   |                            
-----------------
                         -------------                           |   Box 
3      |
                         192.168.1.101                           

---------------

192.168.3.101
My Problem is

A) I am unable to ping from Box 3 (192.168.3.101) to Box 1(192.168.1.101). Any comments or reasons why?
B) I have figured out that if I enable Masquerading then problem A is solved. Can someone explain why?
C) Is it possible without Masquerading ?

I am in a fix and any Help would be very much appreciated...??

Thanks and Regards
Dp

Quoted 75 lines · Dhirendra Pal Singh

Hi All..
I think the image got screwed up...
I am giving the description again..

Dsl feed goes to gateway 1. Its internal ip address is of 192.168.1.XXX. Now from here goes the feed to another gateway which eth0 ip address is 192,168.1.50. It has 2 more eth - eth1 and eth2. Their ip address are 192.168.2.51 and 192.168.3.XXX respectively. Now my problem is that all the computers connect to 192.168.2.XXX are unable to point to the computers of 192.168.1.XXX. Though strangely I can ping to 192.168.1.1 wich is the internal ip address of the gateway 1.

Can someone help me whith this configuration...?
rest question are below..
Thanks in advance ..
dp

Quoted 44 lines · Dhirendra Pal Singh

Hi All,
I have the following setup on redhat linux 8.0 ...

eth 0
192.168.1.50

                                                                   \
                    |--------------|                              \ 
|--------------|
-----------------| gateway 1|-------------------------|gateway2  |
                   /|_______   |\                               
|--------------|
                 /                      \                             
/                  \
           eth0                   eth1 -                       
/                       \
       61.X.X.X          192.168.1.1              eth1                
   eth2
     (public)                         |                
192.168.2.51        192.168.3.52
                                           |                          
                           |
                                   ------------                       
                       |
                                   |  BOX 1   

|
----------------
-------------
| Box
BOX 3 |

192.168.1.101 ---------------

               192.168.3.101

My Problem is

A) I am unable to ping from Box 3 (192.168.3.101) to Box 1. Any comments or reasons why?
B) I have figured out that if I enable Masquerading then problem A is solved. Can someone explain why?
C) Is it possible without Masquerading ?

I am in a fix and any Help would be very much appreciated...??

Quoted 10 lines

Thanks and Regards
Dp

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Quoted 5 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Not sure I can help, but I would try using 'traceroute' to see how far your packets travel.

My guess is that your have:

- A mal-formed routing table on the box using Masquerading. For a network like yours, consider using a dynamic routing deamon like 'gated' or 'routed', if you are having problems.

- You do not have packet-forwarding switched on. Look at the output of 'cat /proc/sys/net/ipv4/ip_forward'. Ensure it's set to '1'.

- Your iptables/ipchains do not have the forwarding chain is set to '-j ACCEPT' for the relevent connection. Check the default policy as well.

- Your iptables/ipchains are blocking you connection, which NAPT bypasses.

- Your netmasks are incorrect. I guess all your networks are sudo-Class-C? Ensure they are all set to '255.255.255.0' or '/24'.

Ben.

Quoted 129 lines · Dhirendra Pal Singh

Thanks to David and Martin,

Okay I am copying the diagram again.. I remade it in acsi and replaced the tabs with space.Have tested it on my box by sending the email to myself and another box. It looks fine..

I hope it dosent breaks this time

                                     eth 0 192.168.1.50
                                                  \
                |----------|                       \ |--------------|
-----------------| gateway 1|-------------------------|gateway2  |
               /|_______   |\                        |--------------|
              /              \                      /                  \
          eth0             eth1 -                  /                    \
      61.X.X.X          192.168.1.1              eth1                   
eth2
    (public)                 |                192.168.2.51        
192.168.3.52
                             |                                        |
                        ------------                                  |
                        |  BOX 1   |                            
-----------------
                        -------------                           |   Box 
3      |
                        192.168.1.101                           

---------------

192.168.3.101
My Problem is

A) I am unable to ping from Box 3 (192.168.3.101) to Box 1(192.168.1.101). Any comments or reasons why?
B) I have figured out that if I enable Masquerading then problem A is solved. Can someone explain why?
C) Is it possible without Masquerading ?

I am in a fix and any Help would be very much appreciated...??

Thanks and Regards
Dp

Quoted 75 lines · Dhirendra Pal Singh

Hi All..
I think the image got screwed up...
I am giving the description again..

Dsl feed goes to gateway 1. Its internal ip address is of 192.168.1.XXX. Now from here goes the feed to another gateway which eth0 ip address is 192,168.1.50. It has 2 more eth - eth1 and eth2. Their ip address are 192.168.2.51 and 192.168.3.XXX respectively. Now my problem is that all the computers connect to 192.168.2.XXX are unable to point to the computers of 192.168.1.XXX. Though strangely I can ping to 192.168.1.1 wich is the internal ip address of the gateway 1.

Can someone help me whith this configuration...?
rest question are below..
Thanks in advance ..
dp

Quoted 44 lines · Dhirendra Pal Singh

Hi All,
I have the following setup on redhat linux 8.0 ...

eth 0
192.168.1.50

                                                                   \
                    |--------------|                              \ 
|--------------|
-----------------| gateway 1|-------------------------|gateway2  |
                   /|_______   |\                               
|--------------|
                 /                      \                             
/                  \
           eth0                   eth1 -                       
/                       \
       61.X.X.X          192.168.1.1              eth1                
   eth2
     (public)                         |                
192.168.2.51        192.168.3.52
                                           |                          
                           |
                                   ------------                       
                       |
                                   |  BOX 1   

|
----------------
-------------
| Box
BOX 3 |

192.168.1.101 ---------------

               192.168.3.101

My Problem is

A) I am unable to ping from Box 3 (192.168.3.101) to Box 1. Any comments or reasons why?
B) I have figured out that if I enable Masquerading then problem A is solved. Can someone explain why?
C) Is it possible without Masquerading ?

I am in a fix and any Help would be very much appreciated...??

Quoted 10 lines

Thanks and Regards
Dp

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Quoted 5 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/