connecting IMQ to different interfaces
Ok, I'm pretty new to this stuff, so I hope this question doesn't appear stupid:
How do I connect an IMQ to different network interfaces?
eg...say I want to control OUTGOING traffic normally on 3 different interfaces:
tc qdisc add dev "eth0" root handle 1: htb default 1
tc class add dev "eth0" parent 1: classid 1:1 htb rate 200kbit ceil 350kbit prio 2
tc qdisc add dev "eth1" root handle 1: htb default 1
tc class add dev "eth1" parent 1: classid 1:1 htb rate 200kbit ceil 350kbit prio 2
tc qdisc add dev "eth2" root handle 1: htb default 1
tc class add dev "eth2" parent 1: classid 1:1 htb rate 200kbit ceil 350kbit prio 2
now I want to control INCOMING traffic to the three different interfaces with IMQ:
tc qdisc add dev "imq0" root handle 1: htb default 1
tc class add dev "imq0" parent 1: classid 1:1 htb rate 2000kbit prio 3
iptables -t mangle -A PREROUTING -i eth0 -j IMQ --todev 0 ip link set "imq0" up
tc qdisc add dev "imq1" root handle 1: htb default 1
tc class add dev "imq1" parent 1: classid 1:1 htb rate 2000kbit prio 3
iptables -t mangle -A PREROUTING -i eth1 -j IMQ --todev 1 ip link set "imq1" up
Now how do I apply it to the third interface? I've run out of imq's! Thanks guys
craig
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 30 lines · Craig J Howard
Ok, I'm pretty new to this stuff, so I hope this question doesn't appear stupid:
How do I connect an IMQ to different network interfaces?
eg...say I want to control OUTGOING traffic normally on 3 different interfaces:
tc qdisc add dev "eth0" root handle 1: htb default 1
tc class add dev "eth0" parent 1: classid 1:1 htb rate 200kbit ceil 350kbit prio 2tc qdisc add dev "eth1" root handle 1: htb default 1
tc class add dev "eth1" parent 1: classid 1:1 htb rate 200kbit ceil 350kbit prio 2tc qdisc add dev "eth2" root handle 1: htb default 1
tc class add dev "eth2" parent 1: classid 1:1 htb rate 200kbit ceil 350kbit prio 2now I want to control INCOMING traffic to the three different interfaces with IMQ:
tc qdisc add dev "imq0" root handle 1: htb default 1
tc class add dev "imq0" parent 1: classid 1:1 htb rate 2000kbit prio 3iptables -t mangle -A PREROUTING -i eth0 -j IMQ --todev 0 ip link set "imq0" up
Quoted 7 lines
tc qdisc add dev "imq1" root handle 1: htb default 1
tc class add dev "imq1" parent 1: classid 1:1 htb rate 2000kbit prio 3iptables -t mangle -A PREROUTING -i eth1 -j IMQ --todev 1 ip link set "imq1" up
Now how do I apply it to the third interface? I've run out of imq's!
RTFM:
If you compile the imq as module and you do a modprobe for it, there is an option that you can specify so you can say how many imq devices you want. modprobe imq numdevs=3
Stef
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/