Skip to contentSkip to conversation

Enabling Proxy Arp

LARTC [email protected] 2 participants 2 messages Apr 3, 2003

lore
Share & tools
lore
#0 lore raw

I have read the section http://lartc.org/howto/lartc.bridging.proxy-arp.html . I configured my two ethernet devices with the same ip address . Should i configure them with a specific command ?

I used : ifconfig eth0 192.168.47.104 netmask 255.255.255.0

	     ifconfig eth1 192.168.47.104 netmask 255.255.255.0

I tried to configure them with ip also .

eth0 Link encap:Ethernet HWaddr 00:90:27:72:B8:1D
inet addr:192.168.47.104 Bcast:192.168.47.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:9

eth1 Link encap:Ethernet HWaddr 00:00:E8:8D:0C:DC
inet addr:192.168.47.104 Bcast:192.168.47.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:9 Base address:0x2000

I checked for support in kernel

# dmesg |grep ip_
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
Is there any specific kernel option for proxy-arp ?

then i tried to enable proxy arp with :
echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp
echo 1 > /proc/sys/net/ipv4/conf/eth1/proxy_arp
but proxy_arp remains 0 , whatever i do .

Thank you for your help
Nikolaos Kefalas

--
http://www.freemail.gr - δωρεάν υπηρεσία ηλεκτρονικού ταχυδρομείου.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Nikolaos,

: I have read the section
: http://lartc.org/howto/lartc.bridging.proxy-arp.html . I configured my : two ethernet devices with the same ip address . Should i configure them : with a specific command ?
:
: I used : ifconfig eth0 192.168.47.104 netmask 255.255.255.0
: ifconfig eth1 192.168.47.104 netmask 255.255.255.0
:
: I tried to configure them with ip also .

You don't need to use the same IP on both interfaces, but I don't see a problem if you do so.

<snip/>

: I checked for support in kernel
: # dmesg |grep ip_
: ip_conntrack version 2.1 (4095 buckets, 32760 max) - 292 bytes per conntrack : ip_tables: (C) 2000-2002 Netfilter core team
: Is there any specific kernel option for proxy-arp ?

OK, so there's not much here, but you may find the tidbit you seek here:

http://linux-ip.net/html/ether-arp.html#ether-arp-proxy

See also Julian's remarks (this includes comments on medium_id, which you don't need), which should give you a good idea of how to perform proxy ARP with the kernel.

http://www.ssi.bg/~julian/#medium_id

Or, if you don't want the kernel to perform proxy ARP, you can use this technique, which employs /sbin/arp directly to add proxy ARP entries:

http://linux-ip.net/html/adv-proxy-arp.html

The benefit of manual proxy ARP entries is a very fine-grained control over which machines are visible to each side of your proxy ARP'ing router.

: then i tried to enable proxy arp with :
: echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp : echo 1 > /proc/sys/net/ipv4/conf/eth1/proxy_arp : but proxy_arp remains 0 , whatever i do .

This is exactly what you wish to do, but you forgot one other sysctl:

echo 1 > /proc/sys/net/ipv4/conf/all/proxy_arp

See Oskar Andreasson's sysctl tutorial for some more details on how to use the net/ipv4/conf sysctl variables.

http://ipsysctl-tutorial.frozentux.net/

Best of luck,

-Martin

Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/