Skip to contentSkip to conversation

IMQ+HTB problem

LARTC hare ram 2 participants 4 messages Apr 15, 2003

lore
Share & tools
lore

hare ram

author
#0 lore raw

Hi all and tc Gururs

i have patched the IMQ and htb to kernel, but when i do egress filtering, iam not able to see any traffic

and excusted the following the commands

modprobe imq numdevs=1

tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 100kbit

tc qdisc add dev imq0 parent 1:1 handle 10: htb default 1 tc class add dev imq0 parent 10: classid 10:10 htb rate 100kbit tc qdisc add dev imq0 parent 10:10 handle 20: sfq

iptables -t mangle -A POSTROUTING -p tcp --dport 80 -j IMQ

ip link set imq0 up

when i see the Iptables Out Put

[root@bridge root]# iptables -xnvL -t mangle
Chain PREROUTING (policy ACCEPT 122928 packets, 16888665 bytes)
pkts bytes target prot opt in out source
destination

Chain INPUT (policy ACCEPT 15068 packets, 1185569 bytes)
pkts bytes target prot opt in out source
destination

Chain FORWARD (policy ACCEPT 116790 packets, 16553990 bytes)
pkts bytes target prot opt in out source
destination

Chain OUTPUT (policy ACCEPT 4943 packets, 670996 bytes)
pkts bytes target prot opt in out source
destination

Chain POSTROUTING (policy ACCEPT 121733 packets, 17224986 bytes)
pkts bytes target prot opt in out source
destination

and also out put of tc

[root@bridge root]# tc -s -d qdisc show
qdisc sfq 20: dev imq0 limit 128p quantum 1500b flows 128/1024
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc htb 10: dev imq0 r2q 10 default 1 direct_packets_stat 0 ver 3.6
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc htb 1: dev imq0 r2q 10 default 1 direct_packets_stat 0 ver 3.6
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

and ifconfig of imq device

imq0 Link encap:UNSPEC HWaddr
00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP RUNNING NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:30
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

i dont see any trffic at all

what is could be the wrong

some expert coments will be helpful

hare

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 5 lines

i have patched the IMQ and htb to kernel, but when i do egress filtering, iam not able to see any traffic

and excusted the following the commands

Quoted 8 lines

modprobe imq numdevs=1

tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 100kbit

tc qdisc add dev imq0 parent 1:1 handle 10: htb default 1 tc class add dev imq0 parent 10: classid 10:10 htb rate 100kbit tc qdisc add dev imq0 parent 10:10 handle 20: sfq

Never add a htb qdisc to a htb class. It will only add extra delays.

Quoted 20 lines

iptables -t mangle -A POSTROUTING -p tcp --dport 80 -j IMQ

ip link set imq0 up

when i see the Iptables Out Put

[root@bridge root]# iptables -xnvL -t mangle
Chain PREROUTING (policy ACCEPT 122928 packets, 16888665 bytes)
pkts bytes target prot opt in out source
destination

Chain INPUT (policy ACCEPT 15068 packets, 1185569 bytes)
pkts bytes target prot opt in out source
destination

Chain FORWARD (policy ACCEPT 116790 packets, 16553990 bytes)
pkts bytes target prot opt in out source
destination

Quoted 7 lines

Chain OUTPUT (policy ACCEPT 4943 packets, 670996 bytes)
pkts bytes target prot opt in out source
destination

Chain POSTROUTING (policy ACCEPT 121733 packets, 17224986 bytes)
pkts bytes target prot opt in out source
destination

Euh. Where is your iptables command ????

Quoted 9 lines

and also out put of tc

[root@bridge root]# tc -s -d qdisc show
qdisc sfq 20: dev imq0 limit 128p quantum 1500b flows 128/1024
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc htb 10: dev imq0 r2q 10 default 1 direct_packets_stat 0 ver 3.6
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc htb 1: dev imq0 r2q 10 default 1 direct_packets_stat 0 ver 3.6
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

So nothing is queued in the imq device. First, you have to get your iptables command working. So packets are queued in the imq device.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
author
#2 lore raw
In reply to hare ram

Hi thanks for the quick reply
check the my questions and answers below in caps

----- Original Message -----
From: "Stef Coene" <[email protected]>
To: "hare ram" <[email protected]>; <[email protected]>
Sent: Tuesday, April 15, 2003 6:53 PM
Subject: Re: [LARTC] IMQ+HTB problem

Quoted 1 line
Quoted 1 line

i have patched the IMQ and htb to kernel, but when i do egress

filtering,

Quoted 6 lines
Quoted 6 lines

iam not able to see any traffic

and excusted the following the commands

modprobe imq numdevs=1

Quoted 8 lines
Quoted 6 lines

tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 100kbit

tc qdisc add dev imq0 parent 1:1 handle 10: htb default 1 tc class add dev imq0 parent 10: classid 10:10 htb rate 100kbit tc qdisc add dev imq0 parent 10:10 handle 20: sfq

Never add a htb qdisc to a htb class. It will only add extra delays.

WHAT IS RECOMENDED

Quoted 20 lines
Quoted 20 lines

iptables -t mangle -A POSTROUTING -p tcp --dport 80 -j IMQ

ip link set imq0 up

when i see the Iptables Out Put

[root@bridge root]# iptables -xnvL -t mangle
Chain PREROUTING (policy ACCEPT 122928 packets, 16888665 bytes)
pkts bytes target prot opt in out source
destination

Chain INPUT (policy ACCEPT 15068 packets, 1185569 bytes)
pkts bytes target prot opt in out source
destination

Chain FORWARD (policy ACCEPT 116790 packets, 16553990 bytes)
pkts bytes target prot opt in out source
destination

Quoted 9 lines
Quoted 7 lines

Chain OUTPUT (policy ACCEPT 4943 packets, 670996 bytes)
pkts bytes target prot opt in out source
destination

Chain POSTROUTING (policy ACCEPT 121733 packets, 17224986 bytes)
pkts bytes target prot opt in out source
destination

Euh. Where is your iptables command ????

YES IAM WONDERING WHERE IS THE RULE GONE, THIS IS WHAT MAIN PROBLEM, SEE ABOVE I HAVE EXECUTED THE IPTABLE LINE

Quoted 10 lines
Quoted 9 lines

and also out put of tc

[root@bridge root]# tc -s -d qdisc show
qdisc sfq 20: dev imq0 limit 128p quantum 1500b flows 128/1024
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc htb 10: dev imq0 r2q 10 default 1 direct_packets_stat 0 ver 3.6
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
qdisc htb 1: dev imq0 r2q 10 default 1 direct_packets_stat 0 ver 3.6
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

So nothing is queued in the imq device. First, you have to get your

iptables

Quoted 2 lines

command working. So packets are queued in the imq device.

IAM WONDERING, WHAT COULD BE THE WRONG,ANY SUGGESTIONS

Quoted 10 lines

Stef

--

[email protected]
"Using Linux as bandwidth manager"
http://www.docum.org/
#lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to hare ram
Quoted 2 lines
Quoted 1 line

Never add a htb qdisc to a htb class. It will only add extra delays.

WHAT IS RECOMENDED

Only use classes. You don't need the qdiscs.

Quoted 10 lines
Quoted 7 lines
Quoted 5 lines

iptables -t mangle -A POSTROUTING -p tcp --dport 80 -j IMQ

Chain POSTROUTING (policy ACCEPT 121733 packets, 17224986 bytes)
pkts bytes target prot opt in out source
destination

Euh. Where is your iptables command ????

YES IAM WONDERING WHERE IS THE RULE GONE, THIS IS WHAT MAIN PROBLEM, SEE ABOVE I HAVE EXECUTED THE IPTABLE LINE

I know.
Are you sure you can execute the iptables command and you didn't had any errors? If I do this on my box (I just did iptables -t mangle -A POSTROUTING -p tcp --dport 80) and get a list of the iptables rules, I can see the rule I added. So it works. Can you check it again ?

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/