IMQ problem -- badly need help
Quoted 22 lines · hare ram
Hi all Guru's
I have been try to work on this IMQ more than 4 weeks but i could not get any results
really and badly need to help to achive my setupiam trying to achieve is up+down=total bandwidth, as per the user groups suggestion
i would like to use IMQ to make my setup to achive thismy setup is , RH 9.0 with patch bridge-nf
and patched IMQ with iptables 1.2.8 and POM also done HTB also patched with latest ip routemy bridge is running fine, iam able to use transparent bridge, working that also
laptop---switch--eth1(bridge)eht0--switch--Router--internet
next i have executed small example
Quoted 13 lines
iptables -t mangle -A PREROUTING -i eth1 -j IMQ --todev 0
----
" when i executed above line i got this message
[root@bridge root]# iptables -t mangle -A PREROUTING -i eth1 -j IMQ --todev 0
iptables: target `IMQ' v1.2.6a (I'm v1.2.8).
----
iptables -t mangle -A PREROUTING -i eth1 -p tcp --dport 20 -m state --state ESTABLISHED -j MARK --set-mark 1
iptables -t mangle -A PREROUTING -i eth1 -p tcp --dport 80 -m state --state ESTABLISHED -j MARK --set-mark 2
iptables -t mangle -A PREROUTING -i eth1 -p tcp --dport 25 -m state --state ESTABLISHED -j MARK --set-mark 3
This is your problem. I think the iptables rule is not added. But don't ask me why. Maybe you use the wrong iptables version? I don't know.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hi all Guru's
I have been try to work on this IMQ more than 4 weeks but i could not get any results
really and badly need to help to achive my setup
iam trying to achieve is up+down=total bandwidth, as per the user groups suggestion
i would like to use IMQ to make my setup to achive this
my setup is , RH 9.0 with patch bridge-nf
and patched IMQ with iptables 1.2.8 and POM also done HTB also patched with latest ip route
my bridge is running fine, iam able to use transparent bridge, working that also
laptop---switch--eth1(bridge)eht0--switch--Router--internet
next i have executed small example
modprobe imq numdevs=1
tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 64kbit
tc qdisc add dev imq0 parent 1:1 handle 10: htb default 5
tc class add dev imq0 parent 10: classid 10:1 htb rate 12kbit burst 16kbit prio 3
tc class add dev imq0 parent 10: classid 10:2 htb rate 28kbit burst 16kbit prio 2
tc class add dev imq0 parent 10: classid 10:3 htb rate 16kbit burst 16kbit prio 1
tc class add dev imq0 parent 10: classid 10:5 htb rate 8kbit prio 4
tc qdisc add dev imq0 parent 10:1 handle 21:0 sfq
tc qdisc add dev imq0 parent 10:2 handle 22:0 sfq
tc qdisc add dev imq0 parent 10:3 handle 23:0 sfq
tc qdisc add dev imq0 parent 10:5 handle 24:0 sfq
tc filter add dev imq0 protocol ip pref 1 parent 10: handle 1 fw classid 10:1
tc filter add dev imq0 protocol ip pref 2 parent 10: handle 2 fw classid 10:2
tc filter add dev imq0 protocol ip pref 3 parent 10: handle 3 fw classid 10:3
iptables -t mangle -A PREROUTING -i eth1 -j IMQ --todev 0
----
" when i executed above line i got this message
[root@bridge root]# iptables -t mangle -A PREROUTING -i eth1 -j IMQ --todev 0
iptables: target `IMQ' v1.2.6a (I'm v1.2.8).
----
iptables -t mangle -A PREROUTING -i eth1 -p tcp --dport 20 -m state --state ESTABLISHED -j MARK --set-mark 1
iptables -t mangle -A PREROUTING -i eth1 -p tcp --dport 80 -m state --state ESTABLISHED -j MARK --set-mark 2
iptables -t mangle -A PREROUTING -i eth1 -p tcp --dport 25 -m state --state ESTABLISHED -j MARK --set-mark 3
ip link set imq0 up
iam able to see the packet when i try to browse using my laptop to yahoo.com see below
[root@bridge root]# iptables -xvnL -t mangle
Chain PREROUTING (policy ACCEPT 10929 packets, 1105430 bytes)
pkts bytes target prot opt in out source
destination
0 0 MARK tcp -- eth1 * 0.0.0.0/0
0.0.0.0/0 tcp dpt:20 state ESTABLISHED MARK set 0x1
42 5053 MARK tcp -- eth1 * 0.0.0.0/0
0.0.0.0/0 tcp dpt:80 state ESTABLISHED MARK set 0x2
0 0 MARK tcp -- eth1 * 0.0.0.0/00.0.0.0/0 tcp dpt:25 state ESTABLISHED MARK set 0x3
but iam not able to see any traffic on imq0, see the out put below
br0 Link encap:Ethernet HWaddr 00:00:00:00:CB:3B
inet addr:202.x.x.7 Bcast:202.x.x.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16647 errors:0 dropped:0 overruns:0 frame:0
TX packets:2145 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1040336 (1015.9 Kb) TX bytes:402909 (393.4 Kb)eth0 Link encap:Ethernet HWaddr 00:00:x:x:x:3B
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18992 errors:0 dropped:0 overruns:0 frame:0
TX packets:4908 errors:0 dropped:0 overruns:0 carrier:0
collisions:1 txqueuelen:100
RX bytes:1759678 (1.6 Mb) TX bytes:605918 (591.7 Kb)
Interrupt:15 Base address:0x3000eth1 Link encap:Ethernet HWaddr 00:80:48:x:x:xx
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2773 errors:0 dropped:0 overruns:0 frame:0 TX packets:16615 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100
RX bytes:202939 (198.1 Kb) TX bytes:1590493 (1.5 Mb) Interrupt:11 Base address:0xc800
imq0 Link encap:UNSPEC HWaddr
00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP RUNNING NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:30
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
when i take the TC out out
[root@bridge root]# tc -s class ls dev imq0
class htb 10:1 root leaf 21: prio 3 rate 12Kbit ceil 12Kbit burst 2Kb cburst 1614b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 1092266 ctokens: 861333
class htb 10:2 root leaf 22: prio 2 rate 28Kbit ceil 28Kbit burst 2Kb cburst 1634b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 468113 ctokens: 373714
class htb 10:3 root leaf 23: prio 1 rate 16Kbit ceil 16Kbit burst 2Kb cburst 1619b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 819200 ctokens: 647999
class htb 10:5 root leaf 24: prio 4 rate 8Kbit ceil 8Kbit burst 1609b cburst 1609b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 1287999 ctokens: 1287999
class htb 1:1 root leaf 10: prio 0 rate 64Kbit ceil 64Kbit burst 1680b cburst 1680b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 168099 ctokens: 168099
all are 0 bytes
iam not sure what is wrong, any expert coment will be appriciate
hare
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Do you thing its iptables problem
even i have cheked with iptables 1.2.7a
still iam not succeeded
when i make rules with out IMQ, iam able to see all the traffic even postrouting and prerouting
really confusing this,
hare
----- Original Message -----
From: "Stef Coene" <[email protected]>
To: "hare ram" <[email protected]>; <[email protected]>
Sent: Thursday, April 17, 2003 3:17 PM
Subject: Re: [LARTC] IMQ problem -- badly need help
Quoted 4 lines · hare ram
Quoted 3 lines
Hi all Guru's
I have been try to work on this IMQ more than 4 weeks but i could not
get
Quoted 7 lines
Quoted 7 lines
any results
really and badly need to help to achive my setupiam trying to achieve is up+down=total bandwidth, as per the user groups suggestion
i would like to use IMQ to make my setup to achive this
Quoted 5 lines
Quoted 5 lines
my setup is , RH 9.0 with patch bridge-nf
and patched IMQ with iptables 1.2.8 and POM also done HTB also patched with latest ip routemy bridge is running fine, iam able to use transparent bridge, working
that
Quoted 11 lines
Quoted 11 lines
also
laptop---switch--eth1(bridge)eht0--switch--Router--internet
next i have executed small example
iptables -t mangle -A PREROUTING -i eth1 -j IMQ --todev 0
----
" when i executed above line i got this message [root@bridge root]# iptables -t mangle -A PREROUTING -i eth1 -j
IMQ --todev
Quoted 4 lines
Quoted 4 lines
0
iptables: target `IMQ' v1.2.6a (I'm v1.2.8).
----
iptables -t mangle -A PREROUTING -i eth1 -p tcp --dport 20 -m
state --state
Quoted 2 lines
Quoted 2 lines
ESTABLISHED -j MARK --set-mark 1
iptables -t mangle -A PREROUTING -i eth1 -p tcp --dport 80 -m
state --state
Quoted 2 lines
Quoted 2 lines
ESTABLISHED -j MARK --set-mark 2
iptables -t mangle -A PREROUTING -i eth1 -p tcp --dport 25 -m
state --state
Quoted 3 lines
Quoted 1 line
ESTABLISHED -j MARK --set-mark 3
This is your problem. I think the iptables rule is not added. But don't
ask
Quoted 12 lines
me why. Maybe you use the wrong iptables version? I don't know.
Stef
--
[email protected]
"Using Linux as bandwidth manager"
http://www.docum.org/
#lartc @ irc.oftc.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 3 lines · hare ram
Do you thing its iptables problem
even i have cheked with iptables 1.2.7a
still iam not succeeded
Mhh.
Quoted 4 lines
when i make rules with out IMQ, iam able to see all the traffic even postrouting and prerouting
really confusing this,
I know there are members of this list using imq. Maybe they can help? Anyone? Hallo?
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
It sounds like the imq target shared libraries were not compiled. You need to replace NETFILTER_VERSION by IPTABLES_VERSION in libipt_IMQ.c and libip6t_IMQ.c
Patrick
Quoted 3 lines · hare ram
Quoted 3 lines
Quoted 3 lines
iptables: target `IMQ' v1.2.6a (I'm v1.2.8).
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/