My filter setting is right?
dear, folks.
I want to following policy.
========= policy which i want (eth0)=======
eth0
HTB(1:0)
|
1:1
/ \
/ \
/ \
1:10 1:11
host 1(dst) host 2(dst)
/ | \ / | \
/ | \ / | \
/ | \ / | \
/ | \ / | \
1:21 1:22 1:23 1:31 1:32 1:33
port80 port22 etc. port80 port22 etc.=========================
i use following filter setting (pseudo setting).
is this right?
# for traffic to host1 filter add dev eth0 , prio 0 , match ip dst [host1 IP],match ip dport 80, flowid 1:21 filter add dev eth0 , prio 1 , match ip dst [host1 IP],match ip dport 22, flowid 1:22 filter add dev eth0 , prio 2 , match ip dst [host1 IP],flowid 1:23
#for traffic to host2
filter add dev eth0 , prio 0 , match ip dst [host2 IP],match ip dport 80, flowid 1:31 filter add dev eth0 , prio 1 , match ip dst [host2 IP],match ip dport 22, flowid 1:32 filter add dev eth0 , prio 2 , match ip dst [host2 IP],flowid 1:33
===========================
all etc traffic which destined to host1 must classify to class 1:23.
my filter's priority setting is right?ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿË™¨¥Šx%ŠË,SùšŠYšŸ÷lõ¯ç–m§ÿÿ™¨¥™©ÿvÏZþy™¨¥™©ÿ–+-ŠwèþV«µÁÎY3ÿ†Ûiÿÿåj»\þŠà
Quoted 38 lines · openings
dear, folks.
I want to following policy.
========= policy which i want (eth0)=======>
eth0 HTB(1:0) 1:1 / \ / \ / \ 1:10 1:11 host 1(dst) host 2(dst) / | \ / | \ / | \ / | \ / | \ / | \ / | \ / |\ 1:21 1:22 1:23 1:31 1:32 1:33 port80
port22 etc. port80 port22 etc.=========================>
i use following filter setting (pseudo setting).is this right?
# for traffic to host1 filter add dev eth0 , prio 0 , match ip dst [host1 IP],match ip dport 80, flowid 1:21 filter add dev eth0 , prio 1 , match ip dst [host1 IP],match ip dport 22, flowid 1:22 filter add dev eth0 , prio 2 , match ip dst [host1 IP],flowid 1:23#for traffic to host2
filter add dev eth0 , prio 0 , match ip dst [host2 IP],match ip dport 80, flowid 1:31 filter add dev eth0 , prio 1 , match ip dst [host2 IP],match ip dport 22, flowid 1:32 filter add dev eth0 , prio 2 , match ip dst [host2 IP],flowid 1:33
Quoted 4 lines
===========================
all etc traffic which destined to host1 must classify to class 1:23. my filter's priority setting is right?
The different prio's in the filters are not needed. You only need them to determine the order of the filters. In your case, order doesn't mather for the prio0 and the prio1 filters.
I'm not sure myself, but the lower the prio, the higher the priority. So in your filter setup, your catch-all filter should have the lowest prio.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/