Skip to contentSkip to conversation

QoS upstream bandwidth sharing

LARTC D de Boer 2 participants 2 messages Apr 25, 2003

lore
Share & tools
lore

D de Boer

author
#0 lore raw

My situation is as follows:

pc1 pc2
\ /

    \ /
    hub (LAN) -----eth0_firewall_eth1-----modem-----internet
    / \            |                 

/ \ 192.168.0.1
pc3 pc4

pc1: 192.168.0.2
pc2: 192.168.0.3
pc3: 192.168.0.4
pc4: 192.168.0.5

I want to divide my upload speed (512kbps) evenly amongst pc1, pc2, pc3 and pc4. It should be possible for them to borrow bandwidth from the others when they don't use their share fully. I've done quite some reading, and my kernel is properly compiled. For instance the SFQ class does work. I have been playing around with HTB, but I can't get it to work properly.

What basic HTB setup would I need? Which eth device (1 or 2) should I do the shaping on, if I want to shape the outgoing traffic (I want to divide upload stream from LAN to internet after all)?

What I came up with myself is to have 4 classes (apart from the root class):
one for every pc, and then use tc filters to match the packets coming from 192.168.0.2 to class 1, those from 192.168.0.3 to class 2, etc. How should I do this? Or is there an easier way?

Could the ip masquerading in my firewall pose a problem? At the moment the firewall configuration is very simple and looks like this:
iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE iptables --append FORWARD --in-interface eth1 -j ACCEPT

Thanks in advance,

David

Signature · 6 lines
Dit bericht is gescand op virussen en andere gevaarlijke inhoud door ULCN MailScanner en het bericht lijkt schoon te zijn.
This message has been scanned for viruses and dangerous content by ULCN MailScanner, and is believed to be clean.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw
Quoted 21 lines · D de Boer

My situation is as follows:

pc1 pc2
\ /

    \ /
    hub (LAN) -----eth0_firewall_eth1-----modem-----internet
    / \            |

/ \ 192.168.0.1
pc3 pc4

pc1: 192.168.0.2
pc2: 192.168.0.3
pc3: 192.168.0.4
pc4: 192.168.0.5

I want to divide my upload speed (512kbps) evenly amongst pc1, pc2, pc3 and pc4. It should be possible for them to borrow bandwidth from the others when they don't use their share fully. I've done quite some reading, and my kernel is properly compiled. For instance the SFQ class does work. I have been playing around with HTB, but I can't get it to work properly.

Quoted 3 lines

What basic HTB setup would I need? Which eth device (1 or 2) should I do the shaping on, if I want to shape the outgoing traffic (I want to divide upload stream from LAN to internet after all)?

If you add a htb qdisc to eth0, it will shape all traffic leaving eth0.

Quoted 4 lines

What I came up with myself is to have 4 classes (apart from the root class): one for every pc, and then use tc filters to match the packets coming from 192.168.0.2 to class 1, those from 192.168.0.3 to class 2, etc. How should I do this? Or is there an easier way?

Indeed, you need 4 classes.

Quoted 4 lines

Could the ip masquerading in my firewall pose a problem? At the moment the firewall configuration is very simple and looks like this:
iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE iptables --append FORWARD --in-interface eth1 -j ACCEPT

It will cause problems if you want to shape upload traffic. Upload traffic leaves eth1 so the source address is rewritten to that of the firewall. You can solve this by marking the packets when they are entering the firewall and use that mark when they leave the firewall. You need the fw filter for this.

I have some extra information about shaping on www.docum.org.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/