netfilter passive monitoring
Hi, I've a passive monitor setup with 3 network interfaces. eth2 is the management (normal) interface while eth0 and eth1 are my monitoring interfaces which never transmit.
-----+-----+--------
| |
eth0 eth1so eth0 monitors the traffic one way on the link and vice versa for eth1 (we're using a netoptics tap).
Anyway my question is I would like to pass all traffic received on eth0 and eth1 into netfilter. I thought by placing my rules in the PREROUTING chain of the mangle table would work, since this happens before any routing decision is made. But the packets are never received by netfilter :-(
The packets are entering the box because you can see/filter them using iptraf.
#iptables -t mangle -L PREROUTING -v
Chain PREROUTING (policy ACCEPT 189K packets, 61M bytes)
pkts bytes target prot opt in out source destination
0 0 icmp -- eth0 any anywhere anywhere
0 0 icmp -- eth1 any anywhere anywhere
thanks,
Pádraig.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 23 lines · Padraig Brady
Hi, I've a passive monitor setup with 3 network interfaces. eth2 is the management (normal) interface while eth0 and eth1 are my monitoring interfaces which never transmit.
-----+-----+--------
eth0 eth1
so eth0 monitors the traffic one way on the link and vice versa for eth1 (we're using a netoptics tap).
Anyway my question is I would like to pass all traffic received on eth0 and eth1 into netfilter. I thought by placing my rules in the PREROUTING chain of the mangle table would work, since this happens before any routing decision is made. But the packets are never received by netfilter :-(
The packets are entering the box because you can see/filter them using iptraf.
Quoted 7 lines
#iptables -t mangle -L PREROUTING -v
Chain PREROUTING (policy ACCEPT 189K packets, 61M bytes)
pkts bytes target prot opt in out source destination0 0 icmp -- eth0 any anywhere anywhere
0 0 icmp -- eth1 any anywhere anywhere
I think the nework cards are running in some sort of capture mode like if you run tcpdump. So they capture all packets that are on the wire. But iptables/netfilter only sees the packets entering the hosts. So you can not use iptables/netfilter to monitor all paclets on the wire.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 2 lines · Stef Coene
iptables/netfilter only sees the packets entering the hosts. So you can not use iptables/netfilter to monitor all paclets on the wire.
Try this patch.
http://www.scaramanga.co.uk/code-fu/netfilter-promisc.diff
I have not tried it myself, so if you decide to do that, I would be glad to hear the about your results.
Cheers,
Jussi
Signature · 6 lines
"To do is to be." - Socrates. "To be is to do." - Plato. "Skoo be do be do." - Sinatra. 1024D/805498C0 AC06 7251 B58B 7A3F 0168 758F 3252 F725 8054 98C0 _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 9 lines · Jussi Norlund
Quoted 2 lines · Stef Coene
iptables/netfilter only sees the packets entering the hosts. So you can not use iptables/netfilter to monitor all paclets on the wire.
Try this patch.
http://www.scaramanga.co.uk/code-fu/netfilter-promisc.diffI have not tried it myself, so if you decide to do that, I would be glad to hear the about your results.
Joy.
thanks a lot!
Pádraig.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/