CBQ DEVICE BW?
Hi,
The CBQ config file shud be some thing like this.
DEVICE=eth0,10Mbit,1Mbit
RATE=50Kbit
WEIGHT=5Kbit
Shall i hardcode the DEVICE BW as 10/100 Mbit
or
Shall i use any other tool like ethtool for getting this. ethtool gives Speed: 10Mbps
If so, how about, if i use some other Interfaces other than eth0, like ppp0 or some other?
C'd anybody can give a suggestion over this?
thanks & regards,
Srikanth.
Quoted 13 lines · Srikanth
Hi,
The CBQ config file shud be some thing like this.
DEVICE=eth0,10Mbit,1Mbit
RATEPKbit
WEIGHT=5KbitShall i hardcode the DEVICE BW as 10/100 Mbit
or
Shall i use any other tool like ethtool for getting this. ethtool gives Speed: 10Mbps
Quoted 4 lines
If so, how about, if i use some other Interfaces other than eth0, like ppp0 or some other?
C'd anybody can give a suggestion over this?
Bandwidth should be the real physical bandwidth of the device.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Thanks Stef,
I need to clarify more please.
Quoted 16 lines · Stef Coene
Quoted 13 lines · Srikanth
Hi,
The CBQ config file shud be some thing like this.
DEVICE=eth0,10Mbit,1Mbit
RATE=50Kbit
WEIGHT=5KbitShall i hardcode the DEVICE BW as 10/100 Mbit
or
Shall i use any other tool like ethtool for getting this. ethtool gives Speed: 10Mbps
Quoted 8 lines
Quoted 6 lines
If so, how about, if i use some other Interfaces other than eth0, like ppp0 or some other?
C'd anybody can give a suggestion over this?
Bandwidth should be the real physical bandwidth of the device.
Forgive me, if i'm wrong.
As of my understanding, are the below lines right?
DEVICE BW = Real physical bandwidth of the device
So, Here DEVICE means only the Interface, not the Link, am i right?
&
RATE = Rate assigned to perticular user/network/service.
How much the user/network/service can aquire max. allowable rate?
I can consider as 10/100 Mbps for ethernet interface. So, how about, when i use ppp0 (pppoe) in my CBQ, is it same? bcoz, pppoe uses eth0, am i right?
Quoted 3 lines
Stef
reg,
Srikanth.
Quoted 3 lines
One more question,
Quoted 16 lines · Stef Coene
Quoted 13 lines · Srikanth
Hi,
The CBQ config file shud be some thing like this.
DEVICE=eth0,10Mbit,1Mbit
RATE=50Kbit
WEIGHT=5KbitShall i hardcode the DEVICE BW as 10/100 Mbit
or
Shall i use any other tool like ethtool for getting this. ethtool gives Speed: 10Mbps
Quoted 9 lines
Quoted 6 lines
If so, how about, if i use some other Interfaces other than eth0, like ppp0 or some other?
C'd anybody can give a suggestion over this?
Bandwidth should be the real physical bandwidth of the device.
How do i get the real physical bandwidth of the device?
The below program attached is giving the value 6, on my system. In some other systems, it's giving 2 (don't know whether Kbps/Mbps).
Quoted 2 lines
Stef
/*
* Gets the bandwidth of the interface.
*/
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <errno.h>
#include <db.h>
#include <sys/types.h>
#include <sys/time.h>
#include <fcntl.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
//#include <netdb.h>
#include <linux/in.h>
#include <linux/if.h>
#include "ifstats.h"
extern int errno;
int
IFSGetBandwidth (if_stats_desc_struct * ifsd)
{
//#ifdef HAS_SIOCGIFINDEX
int s, status;
struct ifreq ifr;
struct in_addr ina;
if_ip_addr_union ip;
if (ifsd == NULL)
{
printf("case 1\n");
return (-1);}
/* Must have a specified interface. */
if (ifsd->interface == NULL)
{
printf("case 2\n"); return (-1);
}
/* Create a UDP socket. */
s = socket (AF_INET, SOCK_DGRAM, 0);
if (s < 0)
{
printf("case 3\n"); return (-1);
}
/* Set interface name explicitly from ifsd. */ strncpy (ifr.ifr_name, ifsd->interface, IFNAMSIZ); ifr.ifr_name[IFNAMSIZ - 1] = '\0';
/* Get bandwidth of interface and put into interface request
* * structure.
* */
status = ioctl(s, SIOCGIFINDEX, &ifr);
/* Close socket. */
close (s);
/* ioctl() failed? */
if (status < 0)
{
perror("! Ioctl");
printf("case 4\n"); return (-1);
}
ifsd->bandwidth = ifr.ifr_bandwidth;printf("Hello World\n");
printf("Bandwidth: %i\n", ifsd->bandwidth);
//#endif /* HAS_SIOCGIFINDEX */
return (0);
}
main ()
{
int retVal; if_stats_desc_struct * ifsd;
ifsd = (if_stats_desc_struct *) malloc(sizeof(if_stats_desc_struct));
if (ifsd == NULL)
perror("! Malloc"); ifsd->interface = (char *) malloc(20);
if (ifsd->interface == NULL)
perror("! Malloc");
strcpy(ifsd->interface, "eth0");
retVal = IFSGetBandwidth (ifsd); free(ifsd->interface);
free(ifsd);
printf("retVal = %d\n", retVal);
}
regards,
Srikanth.
Quoted 3 lines
Quoted 7 lines
Forgive me, if i'm wrong.
As of my understanding, are the below lines right?
DEVICE BW = Real physical bandwidth of the device
So, Here DEVICE means only the Interface, not the Link, am i right?
Yes.
Quoted 5 lines
&
RATE = Rate assigned to perticular user/network/service.
How much the user/network/service can aquire max. allowable rate?
Yes. If you add the bounded parameter, you create a maximum for that class.
Quoted 3 lines
I can consider as 10/100 Mbps for ethernet interface. So, how about, when i use ppp0 (pppoe) in my CBQ, is it same? bcoz, pppoe uses eth0, am i right?
I'm not sure about that. But I think you have to use the eth0 speed. Or use htb, no more bandwidth questions needed :)
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Thanks Stef,
I've customized ethtool source, it's giving the correct values depends on the real physical I/F BW. (as per my requirements)
I need only speed from that.
Quoted 20 lines · Stef Coene
Quoted 9 lines
Forgive me, if i'm wrong.
As of my understanding, are the below lines right?
DEVICE BW = Real physical bandwidth of the device
So, Here DEVICE means only the Interface, not the Link, am i right?
Yes.
Quoted 7 lines
&
RATE = Rate assigned to perticular user/network/service.
How much the user/network/service can aquire max. allowable rate?
Yes. If you add the bounded parameter, you create a maximum for that class.
Quoted 8 lines
Quoted 5 lines
I can consider as 10/100 Mbps for ethernet interface. So, how about, when i use ppp0 (pppoe) in my CBQ, is it same? bcoz, pppoe uses eth0, am i right?
I'm not sure about that. But I think you have to use the eth0 speed. Or use htb, no more bandwidth questions needed :)
Yah, from now onwards, no more DEVICE BW questions.
Quoted 4 lines
Stef
Srikanth.