Skip to contentSkip to conversation

Ethernet Bonding

LARTC GoMi 4 participants 4 messages May 26, 2003

lore
Share & tools
lore

GoMi

author
#0 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

I have to DSL connections with the same providrer, but different public IP's, they are connected to my box to one interface each, and i am doing load balancing right now, i would like to know if it is possible to do an ethernet bonding, keeping the load balancing, and treat both ethernets as one. I have already set up the bond, but i do not get right the routing tables. Anyone?

-----BEGIN PGP SIGNATURE-----
Version: PGP 8.0

iQA/AwUBPtJHOn7diNnrrZKsEQJCqgCfaNyCK40JeGPq7cYuEO21UC3ShG4Ani3K NHCBFeydseieOEveBBwAJYkN
=p5pU
-----END PGP SIGNATURE-----
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 6 lines · GoMi

I have to DSL connections with the same providrer, but different public IP's, they are connected to my box to one interface each, and i am doing load balancing right now, i would like to know if it is possible to do an ethernet bonding, keeping the load balancing, and treat both ethernets as one. I have already set up the bond, but i do not get right the routing tables. Anyone?

I think you also need support from your ISP if you want to do this.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to GoMi
Quoted 7 lines · GoMi

I have to DSL connections with the same providrer, but different public IP's, they are connected to my box to one interface each, and i am doing load balancing right now, i would like to know if it is possible to do an ethernet bonding, keeping the load balancing, and treat both ethernets as one. I have already set up the bond, but i do not get right the routing tables. Anyone?

To the best of my knowledge what you are attempting to do will not work without cooperation from the ISP. Usually bonding requires it to be done on both ends not just one.

I am only aware of 1 ISP ever to do this in the U.S. It was Copper Mountain Networks, who is no longer in existence.

If anyone knows of another ISP offering bonded DSL lines please let me know.

So in your case I do not think it will get much better than things are if you are already doing load balancing/redundancy.

Signature · 12 lines
Sincerely,
William L. Thomson Jr.
Support Group
Obsidian-Studios, Inc.
3548 Jamestown Ln.
Jacksonville, FL 32223
Phone/Fax  904.260.2445
http://www.obsidian-studios.com

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to GoMi

On Mon, 26 May 2003 18:56:27 +0200
"GoMi" <[email protected]> wrote:

:
: -----BEGIN PGP SIGNED MESSAGE-----
: Hash: SHA1
:
: I have to DSL connections with the same providrer, but different public IP's, they are connected to my box to one interface each, and i am doing load balancing right now, i would like to know if it is possible to do an ethernet bonding, keeping the load balancing, and treat both ethernets as one. I have already set up the bond, but i do not get right the routing tables. Anyone?

If you're going to use bonding, you need the proper switch support from the other side. For more info, read /usr/src/linux/Documentation/networking/bonding.txt There's enough info in there, I think. ;)

Signature · 5 lines
_____________________________________________________________

"Engineering does not require science. Science helps a lot but
people built perfectly good brick walls long before they knew
why cement works."	-Alan Cox