r2q error with HTB
(This is a re-statement of a question I asked earlier)
I have a number of HTB classes feeding into a root HTB qdisc. Whenever I set the rate on any of the subordinate classes to 78 kpbs or less, I get the following message:
HTB : quantum of class <class ID> is small. Consider r2q change.
I've done some reading about the meaning of r2q, and I understand it now:
quantum = rate/r2q
where:
rate is expressed in kilobits per second quantum is expressed in bytes
r2q has the appropriate units and is 10 by default
Based on what I've read, it's not at all clear why HTB would complain about a rate of 78Kbit. That corresponds to a quantum of 7800 bytes, which is much larger than the maximum Ethernet packet size (1500).
Anyone have a clue?
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 21 lines · Patrick Turley
(This is a re-statement of a question I asked earlier)
I have a number of HTB classes feeding into a root HTB qdisc. Whenever I set the rate on any of the subordinate classes to 78 kpbs or less, I get the following message:
HTB : quantum of class <class ID> is small. Consider r2q change.
I've done some reading about the meaning of r2q, and I understand it now:
quantum = rate/r2q
where:
rate is expressed in kilobits per second quantum is expressed in bytes
r2q has the appropriate units and is 10 by default
Quoted 5 lines
Based on what I've read, it's not at all clear why HTB would complain about a rate of 78Kbit. That corresponds to a quantum of 7800 bytes, which is much larger than the maximum Ethernet packet size (1500).
Anyone have a clue?
Yes. 78kbit = 9.75kbyte. So quantum = 9.75kilobyte/10 = 975byte.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 22 lines · Stef Coene
Quoted 21 lines · Patrick Turley
(This is a re-statement of a question I asked earlier)
I have a number of HTB classes feeding into a root HTB qdisc. Whenever I set the rate on any of the subordinate classes to 78 kpbs or less, I get the following message:
HTB : quantum of class <class ID> is small. Consider r2q change.
I've done some reading about the meaning of r2q, and I understand it now:
quantum = rate/r2q
where:
rate is expressed in kilobits per second quantum is expressed in bytes
r2q has the appropriate units and is 10 by default
Quoted 8 lines
Quoted 5 lines
Based on what I've read, it's not at all clear why HTB would complain about a rate of 78Kbit. That corresponds to a quantum of 7800 bytes, which is much larger than the maximum Ethernet packet size (1500).
Anyone have a clue?
Yes. 78kbit = 9.75kbyte. So quantum = 9.75kilobyte/10 = 975byte.
Stef
<blush>
OK, I wish I hadn't made that silly mistake.
79Kbit = 80896 bits/sec = 10112 bytes/sec
10112 bytes/sec / 10 r2q => quantum > 1000 bytes
I conclude, then, that HTB will spit out a warning when the quantum implied by the subclass drops below 1000 bytes. This is useful information.
As I said before, I have a number of classes feeding into the root. These classes can have widely varying rate limits, and they can change dynamically. Therefore, to avoid encountering the problem that this message indicates, I need to estimate the lowest reasonable rate limit and select an r2q that will just barely keep this rate's quantum above 1000. A lower rate limit of 50Kbit seems reasonable for my application:
50Kbit = 51200 bits/sec = 6400 bytes/sec
6400 bytes/sec / 1000 bytes = 6 r2q
According to Stef's FAQ at
http://qos.dyndns.org:3389/cgi-bin/fom?_highlightWords=r2q&file1, the buit-in limit for the quantum is 60000 bytes. Even though I've reduced the value of r2q, I still won't hit this limit until the rate exceeds:
60000 bytes * 6 r2q = 360000 bytes/sec => 2.74Mbit
This is acceptable.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/