Skip to contentSkip to conversation

Application routing

LARTC [email protected] 2 participants 2 messages Aug 17, 2003 – Aug 24, 2003

lore
Share & tools
lore
#0 lore raw

As requested I am attaching my network topology and routing tables. I can see that my request was a little ambiquous so heres a little more info

NETWORK TOPOLOGY
========
On my linux PC (redhat 7.3) I have two interfaces IF1 & F2. Each is connected to an ADSL router IF1 to R1 and IF2 to R2. The ADSL routers are configured with static NAT active. My networks are private with the addressing scheme.
IF1 address 172.21.1.12
R1 address 172.21.1.11
NET1 address 172.21.0.0/16

IF2 address 172.22.1.12
R2 address 172.22.1.11
NET2 address 172.22.0.0/16

ASSUMPTIONS
=====The network topology as above means that I can guarantee that all incoming frames at IF1 and IF2 will have the destination address as the appropriate IF address. There are no other devices on these networks.

ROUTING TABLES
=======
Add routing tables T1 and T2
ip route add default via 172.21.1.11 dev eth1 table T1 ip route add default via 172.22.1.11 dev eth2 table T2

Add policy rules
ip rule add from 172.21.1.12 table T1
ip rule add from 172.22.1.12 table T2

Show Routing table main:
172.21.0.0/16 dev eth1 scope link
172.22.0.0/16 dev eth2 scope link
127.0.0.0/8 dev lo scope link

Show Routing table T1:
default via 172.21.1.11 dev eth1

Show Routing table T2:
default via 172.22.1.11 dev eth2

Show Rule table:
0: from all lookup local

32764:  from 172.21.1.12 lookup T1
32765:  from 172.22.1.12 lookup T2
32766:  from all lookup main
32767:  from all lookup 253

TESTING
===
INCOMING PACKETS
----------------
With the above configuration I have been able to receive incoming packets and route them back out the interface they have been received on. This works because when the applications respond to a request they swap the IP dest address and IP source address hence I know that the source address has been set correctly, hence my rule applies and hence traffic is sent via the correct interface.

OUTGOING PACKETS
----------------
Here in lies the problem.
I use ping as an application first. If I just ping an address which happens to be accessible via both networks e.g. ping 194.159.243.228 (www.sip.com) then frames will not actually route out of my system. This is because there is no rule or route to return a source address. Now if I include the interface ping -i IF1 194.159.243.228 then frames are sent out on IF1. This works because the ping application binds to the source address of the interface.

MY APPLICATION
=======
I want to be able to simultaneously get the same web page via both routers. Hence in this application the destination address will always be the same. This discounts routing by destination address. As my application resides well above the socket layer, there is no access to the bind facility.

Now this is why I'm thinking of Marking frames with the target interface ID based on the PID of the application. Hence each frame that the application sends will then be marked with either a 1 or a 2. I can then add two further rules which would then route based on the Mark to either T1 or T2 which will. However a response I have received indicates that this is not reliable.

So back to my original question which I suppose is how do you get an application to be able to select the source address if you don't have access to bind ?

Sorry this has been a bit long winded but at least you have the entire picture now

Many thanks

Paul

-----------------------------------------
Email provided by http://www.ntlhome.com/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Paul,

[ Sorry for the slow reply. ]

: As requested I am attaching my network topology and routing tables. I : can see that my request was a little ambiquous so heres a little more : info

[ good and accurate description, based on LARTC HOWTO, snipped ]

: Here in lies the problem. I use ping as an application first. If I just : ping an address which happens to be accessible via both networks e.g. : ping 194.159.243.228 (www.sip.com) then frames will not actually route : out of my system. This is because there is no rule or route to return a : source address. Now if I include the interface ping -i IF1 : 194.159.243.228 then frames are sent out on IF1. This works because the : ping application binds to the source address of the interface.

You could add a multipath route into your main routing table. Then at any given time, a new route lookup in the main routing table would return something at least.

: I want to be able to simultaneously get the same web page via both : routers. Hence in this application the destination address will always : be the same. This discounts routing by destination address.

As an example, I would recommend using "wget --bind-address2.21.1.12"

--bind-address­DRESS
When making client TCP/IP connections, "bind()" to ADDRESS on the local machine. ADDRESS may be speci­ fied as a hostname or IP address. This option can be useful if your machine is bound to multiple IPs.

: As my application resides well above the socket layer, there is no : access to the bind facility.

Ah! Now that's a problem for which I have no solution!

: Now this is why I'm thinking of Marking frames with the target : interface ID based on the PID of the application. Hence each frame : that the application sends will then be marked with either a 1 or a 2. : I can then add two further rules which would then route based on the : Mark to either T1 or T2 which will. However a response I have received : indicates that this is not reliable.

Indeed, it is not. This reply was accurate (to my knowledge).

: So back to my original question which I suppose is how do you get an : application to be able to select the source address if you don't have : access to bind ?

Indeed--unfortunately, this is a problem for which I have no answer. I believe I have seen subsequent postings from you where you are experimenting with using netfilter to route packets out particular interfaces, and I saw somebody else mention a desired netfilter <software type="imagined">-j RT_LOOKUP</software> target.

Best of luck,

-Martin

Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/