Contents of LARTC digest..."
----- Original Message -----
From: <[email protected]>
To: <[email protected]>
Sent: Thursday, October 23, 2003 11:05 AM
Subject: LARTC digest, Vol 1 #1420 - 10 msgs
Quoted 61 lines
Send LARTC mailing list submissions to
[email protected]To subscribe or unsubscribe via the World Wide Web, visit
http://mailman.ds9a.nl/mailman/listinfo/lartc
or, via email, send a message with subject or body 'help' to [email protected]You can reach the person managing the list at
[email protected]When replying, please edit your Subject line so it is more specific than "Re: Contents of LARTC digest..."
Today's Topics:
1. Re: "Help with routing" (Robert Kurjata)
2. Need Suggestion on CBQ Rules. (Raghuveer K)
3. Per host Traffic Shaping bridge, using DSCP (Warwick Chapman)
4. nexthop reachability (Vadiraj C S)
5. Re: 'Help with routing' ([email protected])
6. Split access problems. (Mike Taekema)
7. Re: Per host Traffic Shaping bridge, using DSCP (Stef Coene)
8. esfq (ThEPhP_KiD)
9. RE: Missing parameter descriptions (Marko Buuri)
10. iptables question (Walter D. Wyndroski)--__--__--
Message: 1
Date: Wed, 22 Oct 2003 08:59:05 +0200
From: Robert Kurjata <[email protected]>
Reply-To: Robert Kurjata <[email protected]>
To: [email protected]
Cc: [email protected]
Subject: Re: [LARTC] "Help with routing"Hi nixo,
I suppose you don't preserve properly output address see my postting with script from 15th October this year :)
(append prohibit default:)nnca> the scheme of my LAN is the next:
nnca> eth0 isp1 /32
nnca> eth1 lan de isp1 (LAN With public IP /24)
nnca> eth2 isp2 /32
nnca> eth3 lan de isp2 (LAN With public IP /26)nnca> ip route add 200.47.x.x/24 dev eth0 src 200.47.4.x table 1 nnca> ip route add default via 200.47.4.x table 1
nnca> ip route add 200.80.32.x/26 dev eth2 src 200.80.32.x table 2 nnca> ip route add default via 200.80.32.x table 2
Quoted 4 lines
nnca> ip rule add from 200.47.4.x table 1
nnca> ip rule add from 200.80.32.x table 2nnca> ip route add default scope global nexthop via 200.47.4.x dev eth0
nexthop
Quoted 6 lines
nnca> via
nnca> 200.80.32.x dev eth2nnca> ******
nnca> My problem is this: when I trace from the NETWORK of ISP1,
sometimes the
Quoted 3 lines
nnca> tracer go out from the gateway of ISP2 and vice versa
nnca> And when someone trace an IP from my LAN of ISP1, it`s showme as
before
Quoted 4 lines
nnca> complete the gateway from ISP2 y vice versa.
nnca> Mi question is: what is wrong in my config...??? What I need to put
or is
Quoted 7 lines
nnca> anything wrong with this config???.
nnca> THANKS VERY MUCH AND SORRY FOR MI HIGHSCHOOL ENGLISH.nnca> _______________________________________________ nnca> LARTC mailing list / [email protected] nnca> http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
Quoted 31 lines
Signature · 16 lines
-- Greetings, Robert mailto:[email protected] --__--__-- Message: 2 Date: Wed, 22 Oct 2003 13:12:21 +0530 From: Raghuveer K <[email protected]> Reply-To: Raghuveer K <[email protected]> Organization: Global Security One Ltd. To: Stef Coene <[email protected]> Cc: [email protected], "Martin A. Brown" <[email protected]> Subject: [LARTC] Need Suggestion on CBQ Rules.Quoted 9 lines · Stef Coene
Quoted 6 lines · Raghuveer
Here are the rules Iam applying to control outgoing traffic at WAN(eth0) interface for public hosted services.
Here actual Isp rate = 512Kbit, rate taken = 97% of 512Kbit, eth0 ip is 192.168.1.2tc qdisc add dev eth0 root handle 1: cbq bandwidth 100Mbit avpkt 1000
cell
Quoted 1 line
Quoted 1 line
Quoted 1 line
8 tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 100Mbit
rate
Quoted 55 lines
Quoted 24 lines
Quoted 24 lines
497Kbit weight 49Kbit prio 3 allot 1514 cell 8 maxburst 10 avpkt 1000 bounded
/* Hosted http server bandwidth = 64Kbit */
tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 100Mbit rate 64Kbit weight 6Kbit prio 3 allot 1514 cell 8 maxburst 10 avpkt 1000 tc filter add dev eth0 parent 1:1 protocol ip prio 3 u32 match ip src 192.168.1.2 match ip sport 800xffffclassid 1:2/* Hosted ftp server bandwidth = 64Kbit */
tc class add dev eth0 parent 1:1 classid 1:3 cbq bandwidth 100Mbit rate 64Kbit weight 6Kbit prio 3 allot 1514 cell 8 maxburst 10 avpkt 1000 tc filter add dev eth0 parent 1:1 protocol ip prio 3 u32 match ip src 192.168.1.2 match ip sport 210xffffclassid 1:3/* Default : Rest/Other traffic */
tc class add dev eth0 parent 1:1 classid 1:4 cbq bandwidth 100Mbit rate 369Kbit weight 40Kbit prio 3 allot 1514 cell 8 maxburst 10 avpkt 1000 /* Here I want replace the below rule with a simple rule based only on port i.e by using some default port other than 80, 21 as sport, which according to your last mail is not possible, hence pls check whether the below rule will do for remaining traffic */
tc filter add dev eth0 parent 1:1 protocol ip prio 3 u32 match ip src 0/0 match ip dst 0/0 classid 1:4Quoted 7 lines
Quoted 4 lines
Pls let me know whether the above rules are framed correctly or can be done in a better way.
I can't do it better then you did :)
Stef,
Traffic Control is not taking place after applying the above rules. Here follows the test setup:-
1. The linux m/c 'seth0(100Mbits, WAN)is connected to 128 Kbits ADSL and eth1 to the LAN.
2. I tried doing traffic control for incoming(at eth1) and outgoing(at eth0) traffic using CBQ(above rules).3. In LAN, I connected 3 m/c's(all linux). 4. The ISP rate taken is 97% of 128Kbits. 5. Bandwidth Monitoring is done by using IPTraf on each LAN m/c's.I have few observations and queries, as follows:--
1. Here the ISP rate is fluctuating in the range of 21Kbits to 131 Kbits for 128Kbits ADSL.
2. I have not added any filter for the parent class. Is it required...? What happens if I add...?
3. Is "iptraf " tool OK for monitoring the distribution of bandwidth on each LAN m/c.
4. Whether shall I take outgoing and incoming ISP rate's in 30:70 ratio, i.e 30% if 128Kbits for outgoing Qdisc(eth0) and 70% for incoming Qdisc(eth1). As 128 Kbits rate being asyncronous(ADSL).Can you pls guide me where amI going wrong..?
Quoted 11 lines
Regards
-RaghuQuoted 4 lines
Stef
Signature · 1 line
****** This email is confidential and is intended for the original
recipient(s)
Quoted 1 line
only. If you have erroneously received this mail, please delete it
immediately
Quoted 1 line
and notify the sender. Unauthorized copying, disclosure or distribution of
the
Quoted 1 line
material in this mail is prohibited. Views expressed in this mail are
those of
Quoted 1 line
the individual sender and do not bind Gsec1 Limited. or its subsidiary,
unless
Quoted 24 lines
the sender has done so expressly with due authority of Gsec1.******
--__--__--
Message: 3
Date: Wed, 22 Oct 2003 11:39:51 +0200
From: Warwick Chapman <[email protected]>
To: [email protected]
Cc: [email protected]
Subject: [LARTC] Per host Traffic Shaping bridge, using DSCPHowdy
We would like to set up a Linux Bridge to replace a FreeBSD/ipfw box doing shaping. Currently, we can only chape per IP/protocol on the FreeBSD box, and not by type of traffic (local/international).
Our upstream provider, Internet Solutions (www.is.co.za) differentiates between Local and International Bandwidth as follows:
"Local traffic DSCP bit is set to 20. International is set to 18."
Quoted 6 lines
What steps would be involved in, say, setting up shaping to a host to give it a 32kb International and 64 local. Would it be possible to allow bursting when bandwidth is available?
I have read the LARTC Guide at lartc.org, which has an example of how to shape an particular host, but not how to incorporate matching the DSCP
bit.
Quoted 163 lines
I'm assuming iptables is used to match the DSCP bit, something like the following:
# iptables -t mangle -A INPUT -m dscp --dscp 16 -j ????Once it is matched, though, how does on force it into a queue? Or am I thinking of this in the wrong way?
Regards
Warwick Chapman
Marketing and Operations
Thusa Business Support ccCellular: +27 83 7797 094
Telephone: +27 31 563 1180
Facsimile: +27 31 563 1182
Website: http://www.thusa.co.za-- There are 10 types of people in this world. Those who understand binary, and those who don't.
--__--__--
Message: 4
Date: Wed, 22 Oct 2003 16:49:39 +0530 (IST)
From: Vadiraj C S <[email protected]>
To: [email protected]
Subject: [LARTC] nexthop reachabilityHello all,
I was just wondering If i could do this..
Local___ public_________Gateway1 Subnet IPlocal net |------192.168.1.1--| Internet 192.168.1.0-----| |-------202.202.1.1 |------202.202.1.6--|here goes my routing table
at any subnet say 192.168.1.2 i want some thing like this
1] route to 202.202.1.0/24 via 192.168.1.1 2] default gateway via 202.202.1.1but at second routing configuration I get host unreachable error by both route and ip route command..
Though there is route to 202 network via 192.168.1.1 it says unreachable but I can ping to 202 network..what should I do to achieve this?
Why I need to do is for dead gateway detection, I do not want to check the nexthop reachable or not, i need to know if ISP is reachable..
Any support will be grateful!!
regards
Vadiraj C S--__--__--
Message: 5
Date: Wed, 22 Oct 2003 15:13:29 -0300 (ART)
Subject: Re: [LARTC] 'Help with routing'
From: <[email protected]>
To: <[email protected]>
Cc: <[email protected]>, <[email protected]>Thank you very much for the solution, but I still have a problem and I need help :) . The problem number one has been solved. When I trace from any computer of my LAN, It`s go out from the right ISP. But after a short time, is like if the rute was chached and it back to the same problem. (I´m getting paranoic :-P )
The Problem number two still happens when someone from outside trace an IP from mi LAN. Always the before complete jump is responded for the interface who correnspond to the other ISP.
Do you have an idea what can be the failure... or, can I call this a failure in my config?
THANKS VERY MUCH
Nicolas Fillon
ArgentinaQuoted 52 lines
Hi nixo,
I suppose you don't preserve properly output address see my postting with script from 15th October this year :)
(append prohibit default:)nnca> the scheme of my LAN is the next:
nnca> eth0 isp1 /32
nnca> eth1 lan de isp1 (LAN With public IP /24)
nnca> eth2 isp2 /32
nnca> eth3 lan de isp2 (LAN With public IP /26)nnca> ip route add 200.47.x.x/24 dev eth0 src 200.47.4.x table 1 nnca> ip route add default via 200.47.4.x table 1
nnca> ip route add 200.80.32.x/26 dev eth2 src 200.80.32.x table 2 nnca> ip route add default via 200.80.32.x table 2
nnca> ip rule add from 200.47.4.x table 1
nnca> ip rule add from 200.80.32.x table 2nnca> ip route add default scope global nexthop via 200.47.4.x dev eth0 nexthop nnca> via
nnca> 200.80.32.x dev eth2nnca> ******
nnca> My problem is this: when I trace from the NETWORK of ISP1, sometimes the nnca> tracer go out from the gateway of ISP2 and vice versa
nnca> And when someone trace an IP from my LAN of ISP1, it`s showme as before nnca> complete the gateway from ISP2 y vice versa.
nnca> Mi question is: what is wrong in my config...??? What I need to put or is nnca> anything wrong with this config???.
nnca> THANKS VERY MUCH AND SORRY FOR MI HIGHSCHOOL ENGLISH.nnca> _______________________________________________ nnca> LARTC mailing list / [email protected] nnca> http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
http://lartc.org/Quoted 3 lines
--
Greetings,
Robert mailto:[email protected]--__--__--
Message: 6
From: "Mike Taekema" <[email protected]>
To: <[email protected]>
Date: Wed, 22 Oct 2003 12:03:56 -0700
Subject: [LARTC] Split access problems.
Quoted 3 lines
Good day,
I seem to be having getting my split access scripts to run properly. Here
is
Quoted 92 lines
my
split_accessscript:IF1=eth0
IF2=eth1
IP1.123.124.52
IP2.123.124.240
P1.123.124.1
P2.123.124.251
P1_NET.123.124.0/25
P2_NET.123.124.128/25
IFE0=eth0
IFE1=eth1ip route flush all
ip route add $P1_NET dev $IF1 src $IP1 table $IFE0 ip route add default via $P1 table $IFE0 ip route add $P2_NET dev $IF2 src $IP2 table $IFE1 ip route add default via $P2 table $IFE1
ip route add $P1_NET dev $IF1 src $IP1
ip route add $P2_NET dev $IF2 src $IP2ip route add default via $P1
ip rule add from $IP1 table $IFE0
ip rule add from $IP2 table $IFE1exit 0
Now here is my
rt_tablesfile:#
# reserved values # 255 local 254 main 253 default 0 unspec 2 eth0 4 eth1 # # local # 1 inr.ruhepNow when I run the script I get these errors: (run script using sh -x
split_access)+ IF1=eth0
+ IF2=eth1
+ IP1.123.124.52
+ IP2.123.124.240
+ P1.123.124.1
+ P2.123.124.251
+ P1_NET.123.124.0/25
+ P2_NET.123.124.128/25
+ IFE0=eth0
+ IFE1=eth1
+ ip route flush all
+ ip route add 10.123.124.0/25 dev eth0 src 10.123.124.52 table eth0
+ ip route add default via 10.123.124.1 table eth0
+ ip route add 10.123.124.128/25 dev eth1 src 10.123.124.240 table eth1
+ ip route add default via 10.123.124.251 table eth1 RTNETLINK answers: File exists
+ ip route add 10.123.124.0/25 dev eth0 src 10.123.124.52 RTNETLINK answers: File exists
+ ip route add 10.123.124.128/25 dev eth1 src 10.123.124.240 RTNETLINK answers: File exists
+ ip route add default via 10.123.124.1
RTNETLINK answers: File exists
+ ip rule add from 10.123.124.52 table eth0
RTNETLINK answers: Invalid argument
+ ip rule add from 10.123.124.240 table eth1
RTNETLINK answers: Invalid argument
+ exit 0Why am I getting "file exists and Invalid arguments again?
Thanks in advance
-Mike T.
--__--__--
Quoted 24 lines
Message: 7
From: Stef Coene <[email protected]>
To: Warwick Chapman <[email protected]>, [email protected]
Subject: Re: [LARTC] Per host Traffic Shaping bridge, using DSCP
Date: Wed, 22 Oct 2003 22:06:04 +0200
Cc: [email protected]Quoted 16 lines · Warwick Chapman
Howdy
We would like to set up a Linux Bridge to replace a FreeBSD/ipfw box doing shaping. Currently, we can only chape per IP/protocol on the FreeBSD box, and not by type of traffic (local/international).
Our upstream provider, Internet Solutions (www.is.co.za) differentiates between Local and International Bandwidth as follows:
"Local traffic DSCP bit is set to 20. International is set to 18."What steps would be involved in, say, setting up shaping to a host to give it a 32kb International and 64 local. Would it be possible to allow bursting when bandwidth is available?
I have read the LARTC Guide at lartc.org, which has an example of how to shape an particular host, but not how to incorporate matching the DSCP
bit.
Quoted 8 lines
Quoted 7 lines
I'm assuming iptables is used to match the DSCP bit, something like the following:
# iptables -t mangle -A INPUT -m dscp --dscp 16 -j ????Once it is matched, though, how does on force it into a queue? Or am I thinking of this in the wrong way?
If the packets are marked with iptables, you can use the fw filter to put
the
Quoted 103 lines
packets in a class.
iptables -t mangle -A INPUT -m dscp --dscp 16 -j MARK --set-mark 2Stef
Signature · 43 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.openprojects.net --__--__-- Message: 8 From: "ThE PhP_KiD" <[email protected]> To: <[email protected]> Date: Wed, 22 Oct 2003 17:45:22 -0300 Subject: [LARTC] esfq hi, I want to try esfq in order to make a load balance in my linux router, (both, lan side and interent side) I want that all hosts of my lan haves the same bandwidth avaible. Since linux router are connected to an ISP which privide a variable bandwidth, I think that can't use HTB. Also, in this situation, how can I do to priorize some LAN hosts from others ? Thanks you very much in advance. Andres. --__--__-- Message: 9 Reply-To: <[email protected]> From: "Marko Buuri" <[email protected]> To: <[email protected]> Subject: RE: [LARTC] Missing parameter descriptions Date: Mon, 20 Oct 2003 10:53:34 +0300Quoted 5 lines
Damion de Soto wrote:
Quoted 1 line · Marko Buuri
I've been looking for descriptions of qdisc parameter
"estimator" and u32
Quoted 1 line
parameter "police" (defined by
POLICE_SPEC), but in vain. IQuoted 8 lines
hope someone on
Quoted 1 line
this list can explain these.
Have you seen :
http://lartc.org/howto/lartc.adv-filter.policing.html
with examples for 'police'
http://lartc.org/howto/lartc.cookbook.synflood-protect.html
and
http://lartc.org/howto/lartc.cookbook.ultimate-tc.htmlThank you for replying!
I find that
POLICE_SPEC(term from tc command syntax, not found in the HOWTO) isn't very well or perhaps clearly documented. I figure the first page you sent is trying to say is that the syntax is more or less:
POLICE_SPEC= police [buffer [buffer] | maxburst [maxburst]] [mtu [mtu]| minburst [minburst]] [mpu [mpu]] [rate [rate]] (continue | drop | pass | reclassify)However, the examples you sent are using parameter "burst" not listed above. A novice as myself can find learning Linux traffic control a bit confusing with this kind of discrepancies between the HOWTO, the command syntax and the man pages.
Quoted 1 line
I'm not sure where examples are of 'estimator' usage.
If someone else here knows, please do tell.
Marko
--__--__--
Message: 10
From: "Walter D. Wyndroski" <[email protected]>
To: <[email protected]>
Date: Wed, 22 Oct 2003 23:45:01 -0400
Subject: [LARTC] iptables questionThis is a multi-part message in MIME format.
------=_NextPart_000_0107_01C398F6.82AC90F0
Content-Type: text/plain;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printableFirst off, I know this is the LARTC list, but I've been living on this
list> for over a year now. :) Now with that said, I'm probably going to get flam> ed for my question. :)
Quoted 3 lines
I've read that iptables is a first match wins system. My recent experience is showing that it is a last match wins. I understand that if a packet is
m> atched in prerouting chain, it may be matched again in a subsequent chain u> nless the jump target was drop.
Quoted 2 lines
NOTE: I am not using iptables as a true firewall, much as most people on
th> is list do not. I'm primarily using iptables to mark packets and drop them
Quoted 1 line
for securing my network and to deny all traffic to my router except for a
f> ew exclusive port.s
Quoted 4 lines
The following is an excerpt from my router script on how I'm handling
certa> in traffic to my router and this works: (This example is a last match wins)
Quoted 7 lines
#Deny All Traffic to Interface except SSH and ICMP
$IPTABLES -A FORWARD -i eth+ -t mangle --dst 172.20.0.5 -p icmp -j ACCEPT
#CMTS Link
$IPTABLES -A FORWARD -i eth+ -t mangle --dst 172.20.0.5 -p ! tcp -j DROP
#CMTS Link
$IPTABLES -A FORWARD -i eth+ -t mangle --dst 172.20.0.5 -p tcp --dport !
22> -j DROP #CMTS Link
Quoted 3 lines
##Allow SNMP Calls Via MRTG To This Interface Only $IPTABLES -A FORWARD -i eth3 -t mangle --src 66.28.168.226 --dst
172.20.0.5> -p udp --dport 161 -j ACCEPT
Quoted 1 line
$IPTABLES -A FORWARD -i eth3 -t mangle --src 66.28.168.226 --dst
172.20.0.5> -p udp --dport 162 -j ACCEPT
Quoted 2 lines
This is how I was doing it and it worked: (This example is a first match
wi> ns)
Quoted 4 lines
(note: I was routing the fwmark 1 to blackhole)
##Allow SNMP Calls Via MRTG To This Interface Only $IPTABLES -A PREROUTING -i eth3 -t mangle --src 66.28.168.226 --dst
172.20.> 0.5 -p udp --dport 161 -j ACCEPT
Quoted 1 line
$IPTABLES -A PREROUTING -i eth3 -t mangle --src 66.28.168.226 --dst
172.20.> 0.5 -p udp --dport 162 -j ACCEPT
Quoted 3 lines
#Deny All Traffic to Interface except SSH and ICMP $IPTABLES -A PREROUTING -i eth+ -t mangle --dst 172.20.0.5 -p icmp -j
ACCEP> T #CMTS Link
Quoted 1 line
$IPTABLES -A PREROUTING -i eth+ -t mangle --dst 172.20.0.5 -p ! tcp -j
MARK> --set-mark 1 #CMTS Link
Quoted 1 line
$IPTABLES -A PREROUTING -i eth+ -t mangle --dst 172.20.0.5 -p tcp --dport
!> 22 -j MARK --set-mark 1 #CMTS Link
Quoted 2 lines
I just need someone to tell me when is iptables using first match wins
vers> us last match wins. I think I am missing something but I am not sure. I sta> y so busy with other tasks that I cannot devote the time that I need and wo> uld like to this. Anyway, many thanks in advance.
Quoted 4 lines
Walt Wyndroski
***************************************************************************> *******************
Quoted 3 lines
* This message has been scanned by CityNET's email scanner for viruses and dangerous content *
* and is believed to be clean. CityNET is proud to use MailScanner. For
m> ore information *
Quoted 3 lines
* concerning MailScanner, visit http://www.mailscanner.info
*
***************************************************************************> *******************
Quoted 10 lines
------=_NextPart_000_0107_01C398F6.82AC90F0
Content-Type: text/html;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"> <HTML><HEAD>
<META http-equiv=Content-Type content="text/html;
charset=iso-8859-1">
Quoted 7 lines
<META content="MSHTML 6.00.2800.1264" name=GENERATOR> <STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV><FONT face=Arial size=2>First off, I know this is the LARTC list, but I've
been living on this list for over a year now. :) Now with that said,
I'm
Quoted 3 lines
probably going to get flamed for my question. :)</FONT></DIV> <DIV><FONT face=Arial size=2></FONT> </DIV> <DIV><FONT face=Arial size=2>I've read that iptables is a first match
w> ins
Quoted 2 lines
system. My recent experience is showing that it is a last match wins. I understand that if a packet is matched in prerouting chain, it may be
match> ed
Quoted 3 lines
again in a subsequent chain unless the jump target was drop.</FONT></DIV> <DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>NOTE: I am not using iptables as a true
fi> rewall,
Quoted 1 line
much as most people on this list do not. I'm primarily using iptables to
ma> rk
Quoted 1 line
packets and drop them for securing my network and to deny all traffic to
my>
Quoted 5 lines
router except for a few exclusive port.s</FONT></DIV> <DIV><FONT face=Arial size=2></FONT> </DIV> <DIV><FONT face=Arial size=2></FONT> </DIV> <DIV><FONT face=Arial size=2></FONT> </DIV> <DIV><FONT face=Arial size=2>The following is an excerpt from my
router> script
Quoted 1 line
on how I'm handling certain traffic to my router and this works: (This
exam> ple
Quoted 5 lines
is a last match wins)</DIV>
<DIV> </DIV>
<DIV>#Deny All Traffic to Interface except SSH and ICMP</DIV> <DIV>$IPTABLES -A FORWARD -i eth+ -t mangle --dst 172.20.0.5 -p icmp -j
ACCEPT &nb> sp;
Quoted 2 lines
#CMTS Link</DIV>
<DIV>$IPTABLES -A FORWARD -i eth+ -t mangle --dst 172.20.0.5 -p !
tcp -j
Quoted 1 line
DROP  > ;
Quoted 2 lines
#CMTS Link</DIV>
<DIV>$IPTABLES -A FORWARD -i eth+ -t mangle --dst 172.20.0.5 -p
tcp --dport> ! 22
Quoted 3 lines
-j DROP #CMTS Link</DIV>
<DIV> </DIV>
<DIV>##Allow SNMP Calls Via MRTG To This Interface Only<BR>$IPTABLES -A
FOR> WARD
Quoted 1 line
-i eth3 -t mangle --src 66.28.168.226 --dst 172.20.0.5 -p udp --dport
161 -> j
Quoted 1 line
ACCEPT<BR>$IPTABLES -A FORWARD -i eth3 -t mangle --src
66.28.168.226 --dst>
Quoted 2 lines
172.20.0.5 -p udp --dport 162 -j ACCEPT<BR></DIV>
<DIV>This is how I was doing it and it worked: (This example is a
firs> t
Quoted 7 lines
match wins)</DIV>
<DIV>
<DIV>
<DIV>(note: I was routing the fwmark 1 to blackhole)</DIV> <DIV> </DIV>
<DIV>##Allow SNMP Calls Via MRTG To This Interface Only<BR>$IPTABLES -A PREROUTING -i eth3 -t mangle --src 66.28.168.226 --dst 172.20.0.5 -p
udp --> dport
Quoted 1 line
161 -j ACCEPT<BR>$IPTABLES -A PREROUTING -i eth3 -t mangle --src
66.28.168.> 226
Quoted 3 lines
--dst 172.20.0.5 -p udp --dport 162 -j ACCEPT<BR></DIV></DIV> <DIV>#Deny All Traffic to Interface except SSH and ICMP</DIV> <DIV>$IPTABLES -A PREROUTING -i eth+ -t mangle --dst 172.20.0.5 -p
icm> p -j
Quoted 1 line
ACCEPT &nb> sp; >
Quoted 2 lines
#CMTS Link</DIV>
<DIV>$IPTABLES -A PREROUTING -i eth+ -t mangle --dst 172.20.0.5 -p !
tcp
Quoted 2 lines
-j MARK --set-mark
1 &n> bsp;
Quoted 2 lines
#CMTS Link</DIV>
<DIV>$IPTABLES -A PREROUTING -i eth+ -t mangle --dst 172.20.0.5 -p
tcp --dp> ort !
Quoted 3 lines
22 -j MARK --set-mark 1 #CMTS Link</DIV> <DIV> </DIV>
<DIV>I just need someone to tell me when is iptables using first match
wins>
Quoted 1 line
versus last match wins. I think I am missing something but I am not sure.
I> stay
Quoted 1 line
so busy with other tasks that I cannot devote the time that I need and
woul> d
Quoted 6 lines
like to this. Anyway, many thanks in advance.</DIV> <DIV> </DIV>
<DIV> </DIV>
<DIV>Walt Wyndroski</DIV></DIV></FONT></BODY><br> <br>
<table border="1" cellpadding="0" cellspacing="0" width="100%"
bord> ercolor="#800000">
Quoted 5 lines
<tr>
<td width="100%">
<p align="center"> This message has been scanned by CityNET's
email scanner for viruses and dangerous content <br>
and is believed to be clean. CityNET is proud to use
MailScann> er. For more information <br>
Quoted 12 lines
concerning MailScanner, visit http://www.mailscanner.info</td>
</tr>
</table>
</HTML>------=_NextPart_000_0107_01C398F6.82AC90F0--
--__--__--
Quoted 8 lines
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartcEnd of LARTC Digest
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/