Skip to contentSkip to conversation

tc&htb

LARTC Eddie 2 participants 2 messages Nov 12, 2003

lore
Share & tools
lore

Eddie

author
#0 lore raw

Hi all.
I'm very new to Linux and the whole traffic shaping thing. Now this is what I've got.A 128Kbit line on eth0 and a 100+ network on eth1.The mail server is on the internal network(eth1 side).

This is what I want.
They run banking software that uses port 15000-15010.I want the bank ports and if I'm going to ssh INTO the box to get all bandwidth,that is 128Kbit.Then I want the internal users limited to 96Kbit for web,32 for mail in and out and 10Kbit for other stuff.I also want them all to share bandwidth if not use(banking is not done most of the time but if it is it should get the most)

I got this far and have no idea,I've been reading advance routing and traffic control,but as the song goes,I'm not the sharpest tool int the shed.

This is what I've got so far(taken from
15.10. Example of a full nat solution with QoS)
My main problem,if this is right,is with the filter.I don't know how Please help me because I'm thinking traffic control is a myth? Thanks Eddie

CEIL8
tc qdisc add dev eth0 root handle 1: htb default 13
tc class add dev eth0 parent 1: classid 1:1 htb rate ${CEIL}kbit ceil ${CEIL}kbit tc class add dev eth0 parent 1:1 classid 1:10 htb rate $(CEIL)kbit ceil $(CEIL)kbit prio 0 tc class add dev eth0 parent 1:1 classid 1:11 htb rate 96kbit ceil ${CEIL}kbit prio 1 tc class add dev eth0 parent 1:1 classid 1:12 htb rate 32kbit ceil ${CEIL}kbit prio 2 tc class add dev eth0 parent 1:1 classid 1:13 htb rate 10kbit ceil ${CEIL}kbit prio 2 tc qdisc add dev eth0 parent 1:10 handle 120: sfq perturb 10
tc qdisc add dev eth0 parent 1:11 handle 130: sfq perturb 10
tc qdisc add dev eth0 parent 1:12 handle 140: sfq perturb 10
tc qdisc add dev eth0 parent 1:13 handle 150: sfq perturb 10

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 13 lines · Eddie

Hi all.
I'm very new to Linux and the whole traffic shaping thing. Now this is what I've got.A 128Kbit line on eth0 and a 100+ network on eth1.The mail server is on the internal network(eth1 side).

This is what I want.
They run banking software that uses port 15000-15010.I want the bank ports and if I'm going to ssh INTO the box to get all bandwidth,that is 128Kbit.Then I want the internal users limited to 96Kbit for web,32 for mail in and out and 10Kbit for other stuff.I also want them all to share bandwidth if not use(banking is not done most of the time but if it is it should get the most)

Quoted 8 lines

I got this far and have no idea,I've been reading advance routing and traffic control,but as the song goes,I'm not the sharpest tool int the shed.

This is what I've got so far(taken from
15.10. Example of a full nat solution with QoS)
My main problem,if this is right,is with the filter.I don't know how Please help me because I'm thinking traffic control is a myth?

Your tc commands are ok. For the filters, you can use the u32 filter that can match on port and or ip address or the fw fliter so you can iptables to classify the packets.
For some examples, see www.docum.org

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/