howto mark packets
Hi folks,
Basically I have this :
|Router A| ----- ethernet --- | SWITCH | --- ethernet ---- |ROUTER B|
What I need : to mark packets passing through "ROUTER A" in such way
that the marks remain until they reach "ROUTER B", so that the router can decide what to do with them based on the first router's mark.
The questions :
1. can that be done ?
2. if the answer to the first q. is yes, can that be done w/o patching
the kernel on the first router w/ experimental patches ?
Thankyou,
Cezar Atanasiu
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 4 lines · Cezar Atanasiu
Hi folks,
The questions :1. can that be done ?
not that way, fw mark are lost when you leave the computer
Quoted 2 lines
2. if the answer to the first q. is yes, can that be done w/o patching
the kernel on the first router w/ experimental patches ?
you can do that in a "capillotracté" way (such an idea) by using tunnels (gre or ipip) and doing some iproute2 an A do push packet in a tunnel corresponding to their mark and have B route by interface.
BR,
Signature · 2 lines
Eric Leblond NuFW, Now User Filtering Works (http://www.nufw.org)
Quoted 7 lines · On Mon, 24 Nov 2003 16:43:40 +0100 Eric Leblond <[email protected]> wrote:
Quoted 4 lines · Cezar Atanasiu
Hi folks,
The questions :1. can that be done ?
not that way, fw mark are lost when you leave the computer
I know, that is why I asked.
Quoted 8 lines
Quoted 4 lines
2. if the answer to the first q. is yes, can that be done w/o patching
the kernel on the first router w/ experimental patches ?you can do that in a "capillotracté" way (such an idea) by using tunnels(gre or ipip) and doing some iproute2 an A do push packet in a tunnel corresponding to their mark and have B route by interface.
Hmm, that would become too complicated. There is no other way ?
Quoted 6 lines
BR,
Signature · 2 lines
Eric Leblond NuFW, Now User Filtering Works (http://www.nufw.org)
Signature · 8 lines
Cezar ATANASIU GMB Computers Departamentul Internet Tel/fax: +40 241 619222/673199 _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
hi cezar,
why not use the TOS mark -- it is carried in the packet's tcp header ... you can only have 8 types/marks however ...
cheers
charles
Quoted 18 lines · Cezar Atanasiu
Quoted 7 lines · On Mon, 24 Nov 2003 16:43:40 +0100 Eric Leblond <[email protected]> wrote:
Quoted 4 lines · Cezar Atanasiu
Hi folks,
The questions :1. can that be done ?
not that way, fw mark are lost when you leave the computer
I know, that is why I asked.
Quoted 5 lines
Quoted 4 lines
2. if the answer to the first q. is yes, can that be done w/o patching
the kernel on the first router w/ experimental patches ?
Quoted 13 lines
Quoted 3 lines
you can do that in a "capillotracté" way (such an idea) by using tunnels(gre or ipip) and doing some iproute2 an A do push packet in a tunnel corresponding to their mark and have B route by interface.
Hmm, that would become too complicated. There is no other way ?
Quoted 6 lines
BR,
Signature · 2 lines
Eric Leblond NuFW, Now User Filtering Works (http://www.nufw.org)
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
In answer to CA's question and EL's response,
Along the same lines, if you encapsulated the marked packet (IP in IP) and set (mangled) the TOS bits in the envelope packet, they could carry the mark without modifying the original packet. Would be a completely non-standard usage of the TOS bits (unless they happened to correspond to the reasons that you are marking packets,;>), but - since they wouldn't get out of your area of responsibility, it might provide an easy-to-setup-and-manage alternative. You would only need one "tunnel" that way, not one for each type of mark...
Of course, you could always filter the packet in user-land, encapsulating in an envelope with the mark data, and re-filter again at the second router (again in user-land), to de-cap and re-mark. No kernel patches needed...
Dick Shorter
[email protected]
-----Original Message <editted> -----
Subject: Re: [LARTC] howto mark packets
Quoted 2 lines
2. if the answer to the first q. is yes, can that be done w/o patching
the kernel on the first router w/ experimental patches ?
you can do that in a "capillotracté" way (such an idea) by using tunnels (gre or ipip) and doing some iproute2 an A do push packet in a tunnel corresponding to their mark and have B route by interface.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/