Routing problem !!!
Can anybody help me ?
This is my configuration:
eth0: 10.0.0.2/16
eth1: 10.0.0.1 (inet gateway)
#ip ru l :
0: from all lookup local 32765: from 10.0.0.2 lookup tabla1 32766: from all lookup main 32767: from all lookup default
#ip r l t tabla1
10.0.0.0/16 dev eth0 scope link src 10.0.0.2
127.0.0.0/8 dev lo scope link
default via 10.0.0.1 dev eth0
#ip r l t main
10.0.0.0/16 dev eth0 scope link
#ip r l t local
broadcast 127.255.255.255 dev lo proto kernel scope link src 127.0.0.1
broadcast 10.0.0.0 dev eth0 proto kernel scope link src 10.0.0.2 local 10.0.0.2 dev eth0 proto kernel scope host src 10.0.0.2 broadcast 10.0.255.255 dev eth0 proto kernel scope link src 10.0.0.2 broadcast 127.0.0.0 dev lo proto kernel scope link src 127.0.0.1 local 127.0.0.1 dev lo proto kernel scope host src 127.0.0.1 local 127.0.0.0/8 dev lo proto kernel scope host src 127.0.0.1
why can't i connect to inet ??
thanks
Signature · 5 lines
Vaquer0 <[email protected]> _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
: This is my configuration:
:
:
: eth0: 10.0.0.2/16
: eth1: 10.0.0.1 (inet gateway)
:
: #ip ru l :
:
: 0: from all lookup local : 32765: from 10.0.0.2 lookup tabla1 : 32766: from all lookup main : 32767: from all lookup default
:
:
: #ip r l t tabla1
:
:
: 10.0.0.0/16 dev eth0 scope link src 10.0.0.2
: 127.0.0.0/8 dev lo scope link
: default via 10.0.0.1 dev eth0
:
: #ip r l t main
:
: 10.0.0.0/16 dev eth0 scope link
[ local routing table snipped ]
: why can't i connect to inet ??
Probably because your router doesn't have a way to send packets to 10.0.0.1 even if the source address on the outbound packet is 10.0.0.2. Add one more route to tabla1:
# ip route add 10.0.0.1 dev eth1 table tabla1 # ip route change default via 10.0.0.1 dev eth1 table tabla1
Once you can ping 10.0.0.1 from your policy routing device, then you should be able to hit the Internet from the same device.
You didn't explain anything about what applications or functions this box hosts, so there's nothing more to say here.
-Martin
Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected] _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Martin, as you can see in my last post i have route to 10.0.0.1 in the main routing table , so i have ping to the gateway but i can't connect to inet.
: #ip r l t main
Quoted 3 lines
:
: 10.0.0.0/16 dev eth0 scope link
The only way to connect to inet is adding:
ip r a default via 10.0.0.1 t main
If i add the default gw in table main , i can connect to inet but i'd like to do this in other table.
Can you help me ?
thanks.
Quoted 43 lines · Martin A. Brown
: This is my configuration:
:
:
: eth0: 10.0.0.2/16
: eth1: 10.0.0.1 (inet gateway)
:
: #ip ru l :
:: 0: from all lookup local : 32765: from 10.0.0.2 lookup tabla1 : 32766: from all lookup main : 32767: from all lookup default:
:
: #ip r l t tabla1
:
:
: 10.0.0.0/16 dev eth0 scope link src 10.0.0.2
: 127.0.0.0/8 dev lo scope link
: default via 10.0.0.1 dev eth0
:
: #ip r l t main
:
: 10.0.0.0/16 dev eth0 scope link[ local routing table snipped ]
: why can't i connect to inet ??
Probably because your router doesn't have a way to send packets to 10.0.0.1 even if the source address on the outbound packet is 10.0.0.2. Add one more route to tabla1:
# ip route add 10.0.0.1 dev eth1 table tabla1 # ip route change default via 10.0.0.1 dev eth1 table tabla1Once you can ping 10.0.0.1 from your policy routing device, then you should be able to hit the Internet from the same device.
You didn't explain anything about what applications or functions this box hosts, so there's nothing more to say here.
-Martin
Signature · 5 lines
Vaquer0 <[email protected]> _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/