Skip to contentSkip to conversation

tc troubles

LARTC Hoomaan Naimi [email protected] 1 participant 2 messages Oct 23, 2000

lore
Share & tools
lore

Hoomaan Naimi [email protected]

author
#0 lore raw

<PRE>Hi all,
Its a while we are trying to use &quot;tc&quot; for bandwidth control. But each time we apply tc rules to the network, we experience a lot of service degradation. The usage we are mostly concerned about, is bandwidth control of a group of IP addresses. We mark that subnet with IPChains and then apply the tc rules. These are the rules applied to eth5 in order to limit the uplink of packets marked &quot;7&quot; by ipchains:

# /sbin/tc class sh dev eth5
class cbq 40: root rate 100Mbit (bounded,isolated) prio no-transmit
class cbq 40:1 parent 40: rate 100Mbit prio no-transmit
class cbq 40:300 parent 40:1 leaf 8025: rate 200Kbit (bounded) prio 5
# /sbin/tc qdisc sh dev eth5
qdisc tbf 8025: rate 200Kbit burst 25Kb lat 1us
qdisc cbq 40: rate 100Mbit (bounded,isolated) prio no-transmit
[<A HREF="mailto:root@qos-1">root@qos-1</A> naimi]# /sbin/tc filter sh dev eth5
filter parent 40: protocol ip pref 1 fw
filter parent 40: protocol ip pref 1 fw handle 0x7 classid 40:300
filter parent 40: protocol ip pref 80 u32
filter parent 40: protocol ip pref 80 u32 fh 800: ht divisor 1
filter parent 40: protocol ip pref 80 u32 fh 800::800 order 2048 key ht 800
bkt 0 flowid 40:100

As I mentioned, the service degraded severely: pig time of internet sites increased about 300-500 ms!!
Does anybody know what is wrong with my configuration?

Best Regards
Hoomaan Naimi
Afranet Network Administrator

</PRE>

author
#1 lore raw

<PRE>Dear Sir,
The question exactly arises from here:
How can I monitor the impact of these several settings on the network performance?
How can I monitor the size of the queues, log the packets dropped ,....? I would be thankful if you recommend me some tools or APIs for doing these tasks.

Best Regards
Hoomaan Naimi
Afranet Network Administrator
----- Original Message -----
From: &quot;bert hubert&quot; &lt;<A HREF="mailto:[email protected]">[email protected]</A>&gt;
To: &quot;Hoomaan Naimi&quot; &lt;<A HREF="mailto:[email protected]">[email protected]</A>&gt;
Sent: Monday, October 23, 2000 1:59 PM
Subject: Re: [LARTC] tc troubles

&gt;<i> On Mon, Oct 23, 2000 at 01:45:22PM +0330, Hoomaan Naimi wrote:
</I>&gt;<i> &gt; Hi all,
</I>&gt;<i> &gt; Its a while we are trying to use &quot;tc&quot; for bandwidth control. But each
</I>time
&gt;<i> &gt; we apply tc rules to the network, we experience a lot of service
</I>&gt;<i> &gt; degradation. The usage we are mostly concerned about, is bandwidth
</I>control
&gt;<i> &gt; of a group of IP addresses. We mark that subnet with IPChains and then
</I>apply
&gt;<i> &gt; the tc rules. These are the rules applied to eth5 in order to limit the
</I>&gt;<i> &gt; uplink of packets marked &quot;7&quot; by ipchains:
</I>&gt;<i>
</I>&gt;<i> Try reading the source of CBQ.init, which can set up rules for you. I miss
</I>a
&gt;<i> lot of settings in your output, like weight, cell size etcetera. This
</I>might
&gt;<i> lead to a bad configuration.
</I>&gt;<i>
</I>&gt;<i> Regards,
</I>&gt;<i>
</I>&gt;<i> bert hubert
</I>&gt;<i>
</I>&gt;<i> &gt; # /sbin/tc class sh dev eth5
</I>&gt;<i> &gt; class cbq 40: root rate 100Mbit (bounded,isolated) prio no-transmit
</I>&gt;<i> &gt; class cbq 40:1 parent 40: rate 100Mbit prio no-transmit
</I>&gt;<i> &gt; class cbq 40:300 parent 40:1 leaf 8025: rate 200Kbit (bounded) prio 5
</I>&gt;<i> &gt; # /sbin/tc qdisc sh dev eth5
</I>&gt;<i> &gt; qdisc tbf 8025: rate 200Kbit burst 25Kb lat 1us
</I>&gt;<i> &gt; qdisc cbq 40: rate 100Mbit (bounded,isolated) prio no-transmit
</I>&gt;<i> &gt; [<A HREF="mailto:root@qos-1">root@qos-1</A> naimi]# /sbin/tc filter sh dev eth5
</I>&gt;<i> &gt; filter parent 40: protocol ip pref 1 fw
</I>&gt;<i> &gt; filter parent 40: protocol ip pref 1 fw handle 0x7 classid 40:300
</I>&gt;<i> &gt; filter parent 40: protocol ip pref 80 u32
</I>&gt;<i> &gt; filter parent 40: protocol ip pref 80 u32 fh 800: ht divisor 1
</I>&gt;<i> &gt; filter parent 40: protocol ip pref 80 u32 fh 800::800 order 2048 key ht
</I>800
&gt;<i> &gt; bkt 0 flowid 40:100
</I>&gt;<i> &gt;
</I>&gt;<i> &gt; As I mentioned, the service degraded severely: pig time of internet
</I>sites
&gt;<i> &gt; increased about 300-500 ms!!
</I>&gt;<i> &gt; Does anybody know what is wrong with my configuration?
</I>&gt;<i> &gt;
</I>&gt;<i> &gt; Best Regards
</I>&gt;<i> &gt; Hoomaan Naimi
</I>&gt;<i> &gt; Afranet Network Administrator
</I>&gt;<i> &gt;
</I>&gt;<i> &gt;
</I>&gt;<i> &gt;
</I>&gt;<i> &gt;
</I>&gt;<i> &gt; _______________________________________________
</I>&gt;<i> &gt; LARTC mailing list / <A HREF="mailto:[email protected]">[email protected]</A> </I>&gt;<i> &gt; <A HREF="http://mailman.ds9a.nl/mailman/listinfo/lartc">http://mailman.ds9a.nl/mailman/listinfo/lartc</A> HOWTO:
</I><A HREF="http://ds9a.nl/2.4Routing/">http://ds9a.nl/2.4Routing/</A>
&gt;<i> &gt;
</I>&gt;<i>
</I>&gt;<i> --
</I>&gt;<i> PowerDNS Versatile DNS Services
</I>&gt;<i> Trilab The Technology People
</I>&gt;<i> 'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet
</I>

</PRE>