Skip to contentSkip to conversation

moving to 2.4 routing stuff from 2.2 masq'ing stuff...

LARTC Alex Avriette [email protected] 2 participants 2 messages Nov 27, 2000

lore
Share & tools
lore

Alex Avriette [email protected]

author
#0 lore raw

<PRE>hi, folks. a brief overview of the network:

powermac g3 running linux 2.4.0-test11. (&quot;macachu&quot;)
ppp0: cablemodem upstream (roadrunneresque)
eth0: cablemodem
eth1: local network

generic win laptop

old sun machines (sparc 4, 5, 10, and 20)

a bay networks 32-port switch, 10/100.

macachu is running dhcpd, which is fine. everybody is visible to everybody else on the internal network. macachu is visible to the outside network. nobody else can get out. i set up the machine per the excellent howto at:

<A HREF="http://howto.tucows.com/LDP/HOWTO/mini/Home-Network-mini-HOWTO.html">http://howto.tucows.com/LDP/HOWTO/mini/Home-Network-mini-HOWTO.html</A>

and then went to go through the howto on the LARTC-list homepage. I joined
the list about two weeks ago, knowing I was going to get myself into this
when I started using the 2.4.0 kernel and the advanced router. I followed
the instructions on the LARTC howto, but I'm stuck. I built the latest
package from <A HREF="ftp://ftp.inr.ac.ru/ip-routing/,">ftp://ftp.inr.ac.ru/ip-routing/,</A> so I've got all the binaries, and everything checks out... but I feel completely clueless
because the howto doesnt explain the steps necessary to get from adding
the item to /etc/iproute2/rt_table to actually being able to ping from
192.168.0.2 to any outside address. im not sure where to go.

any heads up would be appreciated. even clue-by-fours. thanks.

alex

Signature · 10 lines
alex avriette [<A HREF="mailto:[email protected]">[email protected]</A>]

&quot;No man who uses EMACS is deserving of love.&quot;
	Tom Christiansen &lt;<A HREF="mailto:[email protected]">[email protected]</A>&gt;,
	_Perl Cookbook_, pp. 653




</PRE>
#1 lore raw

<PRE>On Sun, Nov 26, 2000 at 07:11:33PM -0500, Alex Avriette wrote:

&gt;<i> binaries, and everything checks out... but I feel completely clueless </I>&gt;<i> because the howto doesnt explain the steps necessary to get from adding </I>&gt;<i> the item to /etc/iproute2/rt_table to actually being able to ping from </I>&gt;<i> 192.168.0.2 to any outside address. im not sure where to go. </I>
You need the &quot;masq'ing stuff&quot;, which can be enabled using netfilter. See also Rusty's Remarkably Unreliable Guides, which are mentioned in the HOWTO. One of these guides contains a setup that does everything you need in terms of masquerading.

&gt;<i> &quot;No man who uses EMACS is deserving of love.&quot;
</I>&gt;<i> Tom Christiansen &lt;<A HREF="mailto:[email protected]">[email protected]</A>&gt;,
</I>&gt;<i> _Perl Cookbook_, pp. 653
</I>
I use EMACS a lot :-)

Regards,

bert hubert

Signature · 6 lines
PowerDNS                     Versatile DNS Services  
Trilab                       The Technology People   
'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet


</PRE>