Skip to contentSkip to conversation

cbq ip range?

LARTC Daniel Reilly [email protected] 3 participants 4 messages Feb 6, 2001 – Feb 7, 2001

lore
Share & tools
lore

Daniel Reilly [email protected]

author
#0 lore raw

<PRE>on 2/7/01 9:47 AM, billy at <A HREF="mailto:[email protected]">[email protected]</A> wrote:

&gt;<i> OK, finally I have made cbq run !
</I>&gt;<i> now I would like to know if it is posible to limit a range of IP to a speed.
</I>&gt;<i> something like this :
</I>&gt;<i>
</I>&gt;<i> from 192.168.1.1 to 192.168.1.21 limit to 128K
</I>&gt;<i>
</I>&gt;<i> I don't whant to limit each IP to 128K, what I would like to do is limit all
</I>&gt;<i> 20 IP to have a max of 128K.
</I>&gt;<i>
</I>&gt;<i> Is it posible?
</I>&gt;<i>
</I>&gt;<i>
</I>&gt;<i>
</I>&gt;<i>
</I>&gt;<i>
</I>&gt;<i> _______________________________________________
</I>&gt;<i> LARTC mailing list / <A HREF="mailto:[email protected]">[email protected]</A> </I>&gt;<i> <A HREF="http://mailman.ds9a.nl/mailman/listinfo/lartc">http://mailman.ds9a.nl/mailman/listinfo/lartc</A> HOWTO:
</I>&gt;<i> <A HREF="http://ds9a.nl/2.4Routing/">http://ds9a.nl/2.4Routing/</A>
</I>You could use this to throttle a whole subnet to 128kbit.....I suppose you
could use a different netmask to tighten the range ....

tc qdisc add dev eth1 root handle 1: cbq bandwidth 10Mbit cell 8 avpkt 1000 mpu 64
tc class add dev eth1 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000 tc class add dev eth1 parent 1:0 classid 1:2 cbq bandwidth 10Mbit rate 128Kbit allot 1514 cell 8 weight 12Kbit prio 3 maxburst 20 avpkt 1000 bounded
ip ro chg 192.168.1.0/24 via 192.168.1.254 realm 16
tc filter add dev eth1 parent 1:0 protocol ip prio 100 route to 16 flowid 1:2
echo &quot;THROTTLE dev eth1 128Kbit&quot;

djr

</PRE>

#1 lore raw

<PRE>On Wed, Feb 07, 2001 at 12:10:53PM -0300, billy wrote:
&gt;<i> What do you meen for &quot;same flowid&quot;? </I>&gt;<i> and is there a cbq-howto? if it is, where can I find it? </I>
That's my setup:

tc qdisc add dev eth0 root handle 10: cbq bandwidth 100Mbit avpkt 1000

tc class add dev eth0 parent 10:0 classid 10:10 cbq bandwidth 100Mbit \
rate 512kbit allot 1514 weight 100kbit prio 5 maxburst 1 avpkt 1000 bounded
tc qdisc add dev eth0 parent 10:10 sfq quantum 1514b perturb 15 tc filter add dev eth0 parent 10:0 protocol ip prio 100 u32 match \
ip src xxx.xxx.2.0/28 flowid 10:10
tc filter add dev eth0 parent 10:0 protocol ip prio 100 u32 match \
ip src xxx.xxx.1.3 flowid 10:10

here xxx.xxx.1.3 is customers linux router/squid proxy, which also generates traffic, as do their other addresses (.2.0/28).

flowid = classid, AFAIK.

This works for me. I don't know the correct wording for all this stuff, so please bare with me ;-]

bye,

Signature · 7 lines
Borut
<A HREF="mailto:[email protected]">[email protected]</A>
-----------------
Booze is the answer.  I don't remember the question.


</PRE>
#2 lore raw
In reply to Daniel Reilly [email protected]

<PRE>OK, finally I have made cbq run !
now I would like to know if it is posible to limit a range of IP to a speed. something like this :

from 192.168.1.1 to 192.168.1.21 limit to 128K

I don't whant to limit each IP to 128K, what I would like to do is limit all 20 IP to have a max of 128K.

Is it posible?

</PRE>

#3 lore raw
In reply to Daniel Reilly [email protected]

<PRE>On Tuesday 06 February 2001 12:07, you wrote:
&gt;<i> On Wed, Feb 07, 2001 at 11:47:21AM -0300, billy wrote:
</I>&gt;<i> &gt; I don't whant to limit each IP to 128K, what I would like to do is limit </I>&gt;<i> &gt; all 20 IP to have a max of 128K.
</I>&gt;<i>
</I>&gt;<i> Sure, just add them to the same flowid. This should be added as an </I>&gt;<i> example to the howto, i guess...i tried and it works (or so it seems :-) </I>&gt;<i>
</I>&gt;<i> You can also add xxx.xxx.xxx.xxx/netmask, which is very nice. </I>
What do you meen for &quot;same flowid&quot;?
and is there a cbq-howto? if it is, where can I find it?

thanks, billy

</PRE>