Skip to contentSkip to conversation

cbq question

LARTC Forstner Michael [email protected] 4 participants 11 messages Feb 6, 2001 – May 14, 2001

lore
Share & tools
lore

Forstner Michael [email protected]

author
#0 lore raw

<PRE>Hi all,

I've got following network running:

linux router with 2 NICs and one ISDN card
- the ISDN card is connected to the internet (dialup dynamic ip)
- first NIC subnet 192.168.0.x
- second NIC subnet 192.168.1.x

All computers on both subnets get access to the internet through the linux router with NAT
I would like to split the bandwidth for the 2 subnets (4 KB/s for each subnet)
Question: is it possible with tc, because of the limitation for outgoing traffic only ?
If possible, can someone please help me ?
Example config ? Tool for creating scripts ? Other ?
THX for any help!

---
Best regards,

Forstner Michael

</PRE>

#1 lore raw

[LARTC] CBQ question

Please.
I create simple config.

    CBQ
       |
   class
 |	|
class1   class2

when rate of class1 is high for the rate of class2, finaly rate of class2 exceed the given.
My experiments gives for example if
class1 rate = 90Mbit and class2 rate = 10Mbit so actual rate of class2 can be from 11.4 to 12.5 ( and far more ).

Thank you.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#2 lore raw

Re: [LARTC] CBQ question

In reply to Forstner Michael [email protected]
Quoted 11 lines

Please.
I create simple config.

    CBQ
       |
   class
 | |
class1   class2
Quoted 8 lines

when rate of class1 is high for the rate of class2, finaly rate of class2 exceed the given.
My experiments gives for example if
class1 rate = 90Mbit and class2 rate = 10Mbit so actual rate of class2 can be from 11.4 to 12.5 ( and far more ).

Thank you.

I test for CBQ and get the same result.
This question I asked before, it's maybe weight, avpkt, cbq problem... I change the avpkt to 500Kbit(I don't know why???) and get better accuracy, maybe you can try this.
Another way is change your queueing disciplines(cbq) to tbf, it's really more stable than cbq, it won't get jitter when your avpkt is change.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#3 lore raw

Re: [LARTC] CBQ question

In reply to Forstner Michael [email protected]
Quoted 10 lines · Gery Kahn

Please.
I create simple config.

    CBQ
       |
   class
 |      |
class1   class2
Quoted 5 lines

when rate of class1 is high for the rate of class2, finaly rate of class2 exceed the given.
My experiments gives for example if
class1 rate = 90Mbit and class2 rate = 10Mbit so actual rate of class2 can be from 11.4 to 12.5 ( and far more ).

I tested it also and when you give 1 class more than 75% of bandwidth, it gets less than that. I have tests-results on my website to prove it.

A better setup is this :

      CBQ
       |
     class
       |
     qdisc
   |        |
 class1   class2
Signature · 7 lines
Stef

More QOS info : http://users.belgacom.net/staf/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
#4 lore raw

Re: [LARTC] CBQ question

In reply to Forstner Michael [email protected]
Quoted 10 lines · Gery Kahn

Please.
I create simple config.

    CBQ
       |
   class
 |      |
class1   class2
Quoted 5 lines

when rate of class1 is high for the rate of class2, finaly rate of class2 exceed the given.
My experiments gives for example if
class1 rate = 90Mbit and class2 rate = 10Mbit so actual rate of class2 can be from 11.4 to 12.5 ( and far more ).

I tested it also and when you give 1 class more than 75% of bandwidth, it gets less than that. I have tests-results on my website to prove it.

A better setup is this :

      CBQ
       |
     class
       |
     qdisc
   |        |
 class1   class2
Signature · 8 lines
Stef

More QOS info : http://users.belgacom.net/staf/


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
#5 lore raw

RE: [LARTC] CBQ question

In reply to Forstner Michael [email protected]

It seems that configuration like

      qdisc(CBQ)
       |
     class
   |		|
 class1   class2
 bounded  bounded

doesn't work perfect.The more stable ( accurate ) configuration would be

    qdisc(cbq) 1:0
	|
    class 1:1
	|
    qdisc(cbq) 2:0
    |          |
  class 2:1  class 2:2
    |

qdisc(tbf) 3:0
Now when class 2:1 have rate 10Mbit and class 2:2 = 70Mbit i can have 9.05 and 72.774

Quoted 9 lines

Please.
I create simple config.

    CBQ
       |
   class
 | |
class1   class2
Quoted 8 lines

when rate of class1 is high for the rate of class2, finaly rate of class2 exceed the given.
My experiments gives for example if
class1 rate = 90Mbit and class2 rate = 10Mbit so actual rate of class2 can be from 11.4 to 12.5 ( and far more ).

Thank you.

I test for CBQ and get the same result.
This question I asked before, it's maybe weight, avpkt, cbq problem... I change the avpkt to 500Kbit(I don't know why???) and get better accuracy, maybe you can try this.
Another way is change your queueing disciplines(cbq) to tbf, it's really more stable than cbq, it won't get jitter when your avpkt is change.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#6 lore raw

Re: [LARTC] CBQ question

In reply to Forstner Michael [email protected]
Quoted 19 lines

It seems that configuration like

      qdisc(CBQ)
       |
     class
   | |
 class1   class2
 bounded  bounded

doesn't work perfect.The more stable ( accurate ) configuration would be

    qdisc(cbq) 1:0
|
    class 1:1
|
    qdisc(cbq) 2:0
    |          |
  class 2:1  class 2:2
    |
Quoted 4 lines

qdisc(tbf) 3:0
Now when class 2:1 have rate 10Mbit and class 2:2 = 70Mbit i can have 9.05 and 72.774

I want to do it and make a config

----------------------------------------------------------------------------
--------------------
BANDWIDTH="bandwidth 10Mbit"
RATE="rate 2Mbit"
DEV="dev eth1"
AVP="avpkt 1000"

tc qdisc add $DEV root handle 10: cbq $BANDWIDTH $AVP

tc class add $DEV parent 10:0 classid 10:1 cbq $BANDWIDTH $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

tc qdisc add $DEV parent 10:1 handle 20: cbq bandwidth 2Mbit $AVP

tc class add $DEV parent 20:0 classid 20:1 cbq bandwidth 2Mbit $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

tc filter add $DEV parent 20:0 protocol ip prio 100 u32 match ip src \
$IP flowid 20:1
----------------------------------------------------------------------------
--------------------
but it's not active....the bandwidth is still 10Mbit....
Is my config's error?????

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#7 lore raw

RE: [LARTC] CBQ question

In reply to Forstner Michael [email protected]

Just add one more qdisc

tc qdisc add dev eth1 parent 20:1 tbf rate 2Mbit buffer 30Kb/8 limit 15Kb

-----Original Message-----
From: Juergen [mailto:[email protected]]
Sent: Monday, May 14, 2001 5:02 AM
To: Gery Kahn
Cc: [email protected]
Subject: Re: [LARTC] CBQ question

Quoted 17 lines

It seems that configuration like

      qdisc(CBQ)
       |
     class
   | |
 class1   class2
 bounded  bounded

doesn't work perfect.The more stable ( accurate ) configuration would be

    qdisc(cbq) 1:0
|
    class 1:1
|
    qdisc(cbq) 2:0
    |          |
  class 2:1  class 2:2
    |
Quoted 4 lines

qdisc(tbf) 3:0
Now when class 2:1 have rate 10Mbit and class 2:2 = 70Mbit i can have 9.05 and 72.774

I want to do it and make a config

----------------------------------------------------------------------------
--------------------
BANDWIDTH="bandwidth 10Mbit"
RATE="rate 2Mbit"
DEV="dev eth1"
AVP="avpkt 1000"

tc qdisc add $DEV root handle 10: cbq $BANDWIDTH $AVP

tc class add $DEV parent 10:0 classid 10:1 cbq $BANDWIDTH $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

tc qdisc add $DEV parent 10:1 handle 20: cbq bandwidth 2Mbit $AVP

tc class add $DEV parent 20:0 classid 20:1 cbq bandwidth 2Mbit $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

tc filter add $DEV parent 20:0 protocol ip prio 100 u32 match ip src \
$IP flowid 20:1
----------------------------------------------------------------------------
--------------------
but it's not active....the bandwidth is still 10Mbit....
Is my config's error?????

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#8 lore raw

Re: [LARTC] CBQ question

In reply to Forstner Michael [email protected]
Quoted 4 lines

Just add one more qdisc

tc qdisc add dev eth1 parent 20:1 tbf rate 2Mbit buffer 30Kb/8 limit 15Kb

But I just want to use cbq to bound my bandwidth.
In classid 20:1 should have been limit to 2Mbit (I guess...), but not active.
Or I have to add a tbf in this config???????
If I have to use tbf, I can just use tbf to limit my bandwidth without cbq and it's also work....right??????

Quoted 13 lines
Quoted 8 lines
    qdisc(cbq) 1:0
|
    class 1:1
|
    qdisc(cbq) 2:0
    |          |
  class 2:1  class 2:2
    |
Quoted 4 lines

qdisc(tbf) 3:0
Now when class 2:1 have rate 10Mbit and class 2:2 = 70Mbit i can have 9.05 and 72.774

Quoted 3 lines

I want to do it and make a config

--------------------------------------------------------------------------

--

Quoted 14 lines

--------------------
BANDWIDTH="bandwidth 10Mbit"
RATE="rate 2Mbit"
DEV="dev eth1"
AVP="avpkt 1000"

tc qdisc add $DEV root handle 10: cbq $BANDWIDTH $AVP

tc class add $DEV parent 10:0 classid 10:1 cbq $BANDWIDTH $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

tc qdisc add $DEV parent 10:1 handle 20: cbq bandwidth 2Mbit $AVP

Quoted 8 lines

tc class add $DEV parent 20:0 classid 20:1 cbq bandwidth 2Mbit $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

tc filter add $DEV parent 20:0 protocol ip prio 100 u32 match ip src \
$IP flowid 20:1
--------------------------------------------------------------------------

--

Quoted 7 lines

--------------------
but it's not active....the bandwidth is still 10Mbit.... Is my config's error?????

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

http://ds9a.nl/2.4Routing/

Quoted 1 line

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#9 lore raw

Re: [LARTC] CBQ question

In reply to Forstner Michael [email protected]
Quoted 20 lines

----------------------------------------------------------------------------
--------------------
BANDWIDTH="bandwidth 10Mbit"
RATE="rate 2Mbit"
DEV="dev eth1"
AVP="avpkt 1000"

tc qdisc add $DEV root handle 10: cbq $BANDWIDTH $AVP

tc class add $DEV parent 10:0 classid 10:1 cbq $BANDWIDTH $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

tc qdisc add $DEV parent 10:1 handle 20: cbq bandwidth 2Mbit $AVP

tc class add $DEV parent 20:0 classid 20:1 cbq bandwidth 2Mbit $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

Quoted 6 lines

tc filter add $DEV parent 20:0 protocol ip prio 100 u32 match ip src \
$IP flowid 20:1
----------------------------------------------------------------------------
--------------------
but it's not active....the bandwidth is still 10Mbit....
Is my config's error?????

You miss a filter

tc filter add $DEV parent 10:0 protocol ip prio 100 u32 match ip src $IP flowid 10:1

Stef

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#10 lore raw

Re: [LARTC] CBQ question

In reply to Forstner Michael [email protected]
Quoted 20 lines

----------------------------------------------------------------------------
--------------------
BANDWIDTH="bandwidth 10Mbit"
RATE="rate 2Mbit"
DEV="dev eth1"
AVP="avpkt 1000"

tc qdisc add $DEV root handle 10: cbq $BANDWIDTH $AVP

tc class add $DEV parent 10:0 classid 10:1 cbq $BANDWIDTH $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

tc qdisc add $DEV parent 10:1 handle 20: cbq bandwidth 2Mbit $AVP

tc class add $DEV parent 20:0 classid 20:1 cbq bandwidth 2Mbit $RATE \
allot 1514 weight 200Kbit prio 5 maxburst 20 $AVP \
bounded

Quoted 6 lines

tc filter add $DEV parent 20:0 protocol ip prio 100 u32 match ip src \
$IP flowid 20:1
----------------------------------------------------------------------------
--------------------
but it's not active....the bandwidth is still 10Mbit....
Is my config's error?????

You miss a filter

tc filter add $DEV parent 10:0 protocol ip prio 100 u32 match ip src $IP flowid 10:1

Stef

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/