Skip to contentSkip to conversation

ingress with u32 filter

LARTC [email protected] 1 participant 2 messages Mar 22, 2001 – Mar 23, 2001

lore
Share & tools
lore
#0 lore raw

I could not get u32 filter work with ingress qdisc.

I tried the following commands to limit the incoming rate from 10.1.1.1 to 10kbit/s.
tc qdisc add dev eth1 handle ffff:0 ingress
tc filter add dev eth1 parent ffff:0 protocol ip prio 50 u32 match ip
src 10.1.1.1 police rate 10kbit burst 10kbit mtu 1500 drop
But looks like the filter is not matching any incoming packets from 10.1.1.1
tc -d -s filter is not showing any matched packets.

I was able to get this work using iptables and fw filter with the following commands.

     iptables -A PREROUTING -t mangle -p tcp -s 10.1.1.1 -j MARK --set-mark

1
tc qdisc add dev eth1 handle ffff:0 ingress
tc filter add dev eth1 parent ffff:0 protocol ip prio 50 handle 1 fw
police rate 10kbit burst 10kbit mtu 1500 drop

Is there any restriction that u32 filter cannot be attached to ingress qdisc? Or am i missing something in my configuration.

Thanks
Sridhar

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#1 lore raw

After looking at the example scripts, the only difference i noticed was that i was not specifying the
flowid in my tc filter add command. When i specified the flowid as :1, i was able to get ingress policing
work with u32 filter.

If flowid is a required field for a u32 filter, maybe tc command should return an error.

On a unrelated note, i found that nexthdr option was not working. To match a syn packet, i was able to specify

            match u8 0x02 0xff at 33
I expected that using nexthdr, this can be specifed as
     match u8 0x02 0xff at nexthdr+13

I am using 2.4.2 kernel, with the latest iproute2 (001007)

Thanks
Sridhar

Sent by: [email protected]

To: [email protected], [email protected]
cc:
Subject: [LARTC] ingress with u32 filter

I could not get u32 filter work with ingress qdisc.

I tried the following commands to limit the incoming rate from 10.1.1.1 to 10kbit/s.
tc qdisc add dev eth1 handle ffff:0 ingress
tc filter add dev eth1 parent ffff:0 protocol ip prio 50 u32 match ip
src 10.1.1.1 police rate 10kbit burst 10kbit mtu 1500 drop
But looks like the filter is not matching any incoming packets from 10.1.1.1
tc -d -s filter is not showing any matched packets.

I was able to get this work using iptables and fw filter with the following commands.

     iptables -A PREROUTING -t mangle -p tcp -s 10.1.1.1 -j MARK --set-mark

1
tc qdisc add dev eth1 handle ffff:0 ingress
tc filter add dev eth1 parent ffff:0 protocol ip prio 50 handle 1 fw
police rate 10kbit burst 10kbit mtu 1500 drop

Is there any restriction that u32 filter cannot be attached to ingress qdisc? Or am i missing something in my configuration.

Thanks
Sridhar

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
http://ds9a.nl/2.4Routing/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/