Skip to contentSkip to conversation

I need some advise from a routing Guru !!

LARTC Krepper Guillermo 2 participants 3 messages Apr 18, 2001 – Apr 19, 2001

lore
Share & tools
lore
#0 lore raw

Hi, let's get to bussisnes ...
This is what I have

                                                +--------------------------+
                        eth0 ----------------- |                           |
                                                 |        LINUX          | ---------------- eth1
                        eth2 ----------------- |                           | 
                                                 |        SUPER        | ---------------- eth4
                        eth3 ----------------- |                           |
                                                 |        ROUTER      |
                                                 +--------------------------+

Internet Connections:

    eth0: 200.1.1.0/24
    eth2: 200.2.1.0/24
    eth3: 200.3.1.0/24                    
    from 3 diferent carriers

Private LAN:

    eth1: NAT -->     192.168.1.0/24
                             192.168.2.0/24
                             192.168.3.0/24

Internet Services (DNS, WEB, MAIL, etc)

First of all I'll say that Traffic Controller works 10 points !!!!!

Routing is doing ok, but I'm not shure if it's here were I'm making all the trouble. So here is how I do it.

ip rule add from 192.168.1.0/24 table 1

    ip route add 192.168.1.0/24 via 192.168.1.254 dev eth1 table 1             ( so machines can ping eachother )
    ip route add default via 200.1.1.254 dev eth0

ip rule add from 192.168.2.0/24 table 2

    ip route add 192.168.2.0/24 via 192.168.2.254 dev eth1 table 1             ( so machines can ping eachother )
    ip route add default via 200.1.2.254 dev eth2

ip rule add from 192.168.3.0/24 table 3

    ip route add 192.168.3.0/24 via 192.168.1.254 dev eth1 table 1             ( so machines can ping eachother )
    ip route add default via 200.1.3.254 dev eth3

I think this is ok, it worked, but .......

Well here is my problem on eth4 I would like to put a dns, httpd, smtp, pop and a proxy. All of this have IP that are part of (eth0).
DNS1 = 200.1.1.1 DNS2 = 200.1.1.2

I made all connections work with this DNS but when someone querys the dns, the paket goes to the Internet an then comes back. Is there a way of redirecting or routing it to eth0 before it goes to take a trip? I tested with iptables DNAT, ip route add 200.1.1.1/36 dev eth4 ..... and did not work.
Can somebody give me an advise or a clue on how should I do something like this? an with the proxy? how can I specify on witch eth to go out depending from where it came from TOS Mark? I olso would like a recomendation on some good books, please.

That's all folks,

well thank you verry much for the advise.

Krepper Guillermo (Billy)

#1 lore raw

Hello,

I'm also new to this concept but from what I understand:

1) If you query from 192.168.1.0/24 it works fine. Doesn't it?

2) From 192.168.2.0/24 and 192.168.3.0/24, the packets go to the Internet and come back through your first carrier to hit your DNS servers. Is this right?

If these two assumptions are correct, then your problem is those default routes per private /24's. I think that you need to set static routes to your DNS servers in tables 2 and 3.

This might or might not be the solution to your problem. If so, glad to have been able to help; if not, sorry but I also said that I was new to all these.

Ramin

Quoted 62 lines · Krepper Guillermo

Hi, let's get to bussisnes ...
This is what I have

                                                +--------------------------+
                        eth0 ----------------- |                           |
                                                 |        LINUX          | ---------------- eth1
                        eth2 ----------------- |                           | 
                                                 |        SUPER        | ---------------- eth4
                        eth3 ----------------- |                           |
                                                 |        ROUTER      |
                                                 +--------------------------+

Internet Connections:

    eth0: 200.1.1.0/24
    eth2: 200.2.1.0/24
    eth3: 200.3.1.0/24                    
    from 3 diferent carriers

Private LAN:

    eth1: NAT -->     192.168.1.0/24
                             192.168.2.0/24
                             192.168.3.0/24

Internet Services (DNS, WEB, MAIL, etc)

First of all I'll say that Traffic Controller works 10 points !!!!!

Routing is doing ok, but I'm not shure if it's here were I'm making all the trouble. So here is how I do it.

ip rule add from 192.168.1.0/24 table 1

    ip route add 192.168.1.0/24 via 192.168.1.254 dev eth1 table 1             ( so machines can ping eachother )
    ip route add default via 200.1.1.254 dev eth0

ip rule add from 192.168.2.0/24 table 2

    ip route add 192.168.2.0/24 via 192.168.2.254 dev eth1 table 1             ( so machines can ping eachother )
    ip route add default via 200.1.2.254 dev eth2

ip rule add from 192.168.3.0/24 table 3

    ip route add 192.168.3.0/24 via 192.168.1.254 dev eth1 table 1             ( so machines can ping eachother )
    ip route add default via 200.1.3.254 dev eth3

I think this is ok, it worked, but .......

Well here is my problem on eth4 I would like to put a dns, httpd, smtp, pop and a proxy. All of this have IP that are part of (eth0).
DNS1 = 200.1.1.1 DNS2 = 200.1.1.2

I made all connections work with this DNS but when someone querys the dns, the paket goes to the Internet an then comes back. Is there a way of redirecting or routing it to eth0 before it goes to take a trip? I tested with iptables DNAT, ip route add 200.1.1.1/36 dev eth4 ..... and did not work.
Can somebody give me an advise or a clue on how should I do something like this? an with the proxy? how can I specify on witch eth to go out depending from where it came from TOS Mark? I olso would like a recomendation on some good books, please.

That's all folks,

well thank you verry much for the advise.

Krepper Guillermo (Billy)

Signature · 7 lines
Ramin Alidousti                                         [email protected]
Advanced Development                             tel +1 703 886 2640
UUNET, A WorldCom Company                        fax +1 703 886 0536

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
author
#2 lore raw
In reply to Krepper Guillermo

First of all thanks for you answer

-----Mensaje original-----
De: Ramin Alidousti <[email protected]>
Para: Krepper Guillermo <[email protected]>
CC: [email protected] <[email protected]>
Fecha: Jueves, 19 de Abril de 2001 10:48 a.m.
Asunto: Re: [LARTC] I need some advise from a routing Guru !!

Quoted 5 lines

Hello,

I'm also new to this concept but from what I understand:

1) If you query from 192.168.1.0/24 it works fine. Doesn't it?

No, actually none of the NATs classes (192.168.1.0; 192.168.2.0; 192.168.3.0) can query the dns. They can't ping it. But using iptables DNAT i could do some thing like check mail, telnet, etc. the problem is that the dns and the mail server must go out to the internet to do there work. I'll explain a little more

eth4: 192.168.10.254 (on the linux machine)

eth0: 200.1.1.1 -->DNAT --to 192.168.10.1

             200.1.1.2 -->DNAT --to 192.168.10.2

the dns server is configured with eth1: 192.168.10.1; 192.168.10.2

Here is the DNAT command I'm using, maybe my error is here.

iptables -A PREROUNTING -t nat -d 200.1.1.1 -j DNAT 192.168.1.1 (should I use "-i" option, here ?)

Quoted 9 lines

2) From 192.168.2.0/24 and 192.168.3.0/24, the packets go to the Internet and come back through your first carrier to hit your DNS servers. Is this right?

If these two assumptions are correct, then your problem is those default routes per private /24's. I think that you need to set static routes to your DNS servers in tables 2 and 3.

Quoted 12 lines

This might or might not be the solution to your problem. If so, glad to have been able to help; if not, sorry but I also said that I was new to all these.

Ramin

Quoted 4 lines · Krepper Guillermo

Hi, let's get to bussisnes ...
This is what I have

+--------------------------+
>>                         eth0 ----------------- |
|
>>                                                  |        LINUX
| ---------------- eth1
>>                         eth2 ----------------- |
|
>>                                                  |        SUPER
       | ---------------- eth4
>>                         eth3 ----------------- |
|
>>                                                  |        ROUTER      |
Quoted 1 line
Quoted 1 line

+--------------------------+

Quoted 13 lines
Quoted 13 lines

Internet Connections:

    eth0: 200.1.1.0/24
    eth2: 200.2.1.0/24
    eth3: 200.3.1.0/24
    from 3 diferent carriers

Private LAN:

    eth1: NAT -->     192.168.1.0/24
                             192.168.2.0/24
                             192.168.3.0/24
Quoted 5 lines
Quoted 5 lines

Internet Services (DNS, WEB, MAIL, etc)

First of all I'll say that Traffic Controller works 10 points !!!!!

Routing is doing ok, but I'm not shure if it's here were I'm making all

the trouble. So here is how I do it.

Quoted 3 lines
Quoted 3 lines

ip rule add from 192.168.1.0/24 table 1

    ip route add 192.168.1.0/24 via 192.168.1.254 dev eth1 table 1

( so machines can ping eachother )

Quoted 4 lines
Quoted 4 lines
    ip route add default via 200.1.1.254 dev eth0

ip rule add from 192.168.2.0/24 table 2

    ip route add 192.168.2.0/24 via 192.168.2.254 dev eth1 table 1

( so machines can ping eachother )

Quoted 4 lines
Quoted 4 lines
    ip route add default via 200.1.2.254 dev eth2

ip rule add from 192.168.3.0/24 table 3

    ip route add 192.168.3.0/24 via 192.168.1.254 dev eth1 table 1

( so machines can ping eachother )

Quoted 6 lines
Quoted 6 lines
    ip route add default via 200.1.3.254 dev eth3

I think this is ok, it worked, but .......

Well here is my problem on eth4 I would like to put a dns, httpd, smtp,

pop and a proxy. All of this have IP that are part of (eth0).

Quoted 3 lines
Quoted 3 lines

DNS1 = 200.1.1.1 DNS2 = 200.1.1.2

I made all connections work with this DNS but when someone querys the

dns, the paket goes to the Internet an then comes back. Is there a way of redirecting or routing it to eth0 before it goes to take a trip?

Quoted 1 line
Quoted 1 line

I tested with iptables DNAT, ip route add 200.1.1.1/36 dev eth4 ..... and

did not work.

Quoted 1 line
Quoted 1 line

Can somebody give me an advise or a clue on how should I do something

like this? an with the proxy? how can I specify on witch eth to go out depending from where it came from TOS Mark?

Quoted 12 lines
Quoted 11 lines

I olso would like a recomendation on some good books, please.

That's all folks,

well thank you verry much for the advise.

Krepper Guillermo (Billy)

Quoted 8 lines

--
Ramin Alidousti [email protected]
Advanced Development tel +1 703 886 2640
UUNET, A WorldCom Company fax +1 703 886 0536

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

http://ds9a.nl/2.4Routing/

Quoted 1 line

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/