Marking packets for shaping
Greetings earthlings,
I am batteling to get NATted packets marked with iptables, to shape them later using the fw filter.
Has anyone tried to mark packets that are masqueraded, or to shape masqueraded connections?
It doesn't seem to work.
If any knows what to do, please help.
Regards
- Jaco van der Schyff
[email protected]
+27 12 803 7591
+27 12 803 7285 (f)
+27 83 680 4922 (mobile)
f6e2eb48937f22e159a408c84533cdcb
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
what is/are your setup/rules? It should work just fine.
Ramin
Quoted 21 lines · Jaco van der Schyff
Greetings earthlings,
I am batteling to get NATted packets marked with iptables, to shape them later using the fw filter.
Has anyone tried to mark packets that are masqueraded, or to shape masqueraded connections?
It doesn't seem to work.
If any knows what to do, please help.
Regards
- Jaco van der Schyff
[email protected]+27 12 803 7591
+27 12 803 7285 (f)
+27 83 680 4922 (mobile)
Quoted 5 lines
f6e2eb48937f22e159a408c84533cdcb_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
I removed the comments from the file below, also this isnt the complete file, but it should be enough to give you an idea what I want to acheive.
iptables -A PREROUTING -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK \
--set-mark 1
tc qdisc add dev eth1 root handle 10: cbq bandwidth 64Kbit avpkt 1000
tc class add dev eth1 parent 10:0 classid 10:1 cbq bandwidth 64Kbit rate \
64Kbit allot 1514 weight 6Kbit prio 8 maxburst 20 avpkt 1000
tc class add dev eth1 parent 10:1 classid 10:100 cbq bandwidth 64Kbit rate \
32Kbit allot 1514 weight 3Kbit prio 5 maxburst 20 avpkt 100 bounded
tc qdisc add dev eth1 parent 10:100 sfq quantum 1514b perturb 15
tc filter add dev eth1 protocol ip parent 10:1 prio 100 handle 1 fw classid 1:100
Regards
- Jaco van der Schyff
[email protected]
+27 12 803 7591
+27 12 803 7285 (f)
+27 83 680 4922 (mobile)
f6e2eb48937f22e159a408c84533cdcb
Quoted 33 lines · Ramin Alidousti
what is/are your setup/rules? It should work just fine.
Ramin
Quoted 26 lines · Jaco van der Schyff
Greetings earthlings,
I am batteling to get NATted packets marked with iptables, to shape them later using the fw filter.
Has anyone tried to mark packets that are masqueraded, or to shape masqueraded connections?
It doesn't seem to work.
If any knows what to do, please help.
Regards
- Jaco van der Schyff
[email protected]+27 12 803 7591
+27 12 803 7285 (f)
+27 83 680 4922 (mobile)
f6e2eb48937f22e159a408c84533cdcb_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
I assume that the packets come in on eth0, right? And I'm not sure if the mangle table sees the destination as 192.168.62.0/24 or as the original destination address. Try this:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d 192.168.62.0/24 \ -j MARK --set-mark 1
If it doesn't work, try:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d <orig dst IP's>
-j MARK --set-mark 1
Hope it works,
Ramin
Quoted 40 lines · Jaco van der Schyff
I removed the comments from the file below, also this isnt the complete file, but it should be enough to give you an idea what I want to acheive.
iptables -A PREROUTING -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK \
--set-mark 1tc qdisc add dev eth1 root handle 10: cbq bandwidth 64Kbit avpkt 1000
tc class add dev eth1 parent 10:0 classid 10:1 cbq bandwidth 64Kbit rate \
64Kbit allot 1514 weight 6Kbit prio 8 maxburst 20 avpkt 1000tc class add dev eth1 parent 10:1 classid 10:100 cbq bandwidth 64Kbit rate \
32Kbit allot 1514 weight 3Kbit prio 5 maxburst 20 avpkt 100 boundedtc qdisc add dev eth1 parent 10:100 sfq quantum 1514b perturb 15
tc filter add dev eth1 protocol ip parent 10:1 prio 100 handle 1 fw classid 1:100
Regards
- Jaco van der Schyff
[email protected]+27 12 803 7591 +27 12 803 7285 (f) +27 83 680 4922 (mobile) f6e2eb48937f22e159a408c84533cdcb
Quoted 19 lines
Quoted 18 lines · Ramin Alidousti
what is/are your setup/rules? It should work just fine.
Ramin
Quoted 11 lines · Jaco van der Schyff
Greetings earthlings,
I am batteling to get NATted packets marked with iptables, to shape them later using the fw filter.
Has anyone tried to mark packets that are masqueraded, or to shape masqueraded connections?
It doesn't seem to work.
If any knows what to do, please help.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
I just checked with the iptables guru's and it appears that the mangle table is checked before the nat table meaning that the second example below works and not the first one, which also explains why your setup didn't work.
Ramin
Quoted 9 lines · Ramin Alidousti
I assume that the packets come in on eth0, right? And I'm not sure if the mangle table sees the destination as 192.168.62.0/24 or as the original destination address. Try this:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d 192.168.62.0/24 \ -j MARK --set-mark 1If it doesn't work, try:
Quoted 67 lines
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d <orig dst IP's>
-j MARK --set-mark 1Hope it works,
RaminQuoted 59 lines · Jaco van der Schyff
I removed the comments from the file below, also this isnt the complete file, but it should be enough to give you an idea what I want to acheive.
iptables -A PREROUTING -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK \
--set-mark 1tc qdisc add dev eth1 root handle 10: cbq bandwidth 64Kbit avpkt 1000
tc class add dev eth1 parent 10:0 classid 10:1 cbq bandwidth 64Kbit rate \
64Kbit allot 1514 weight 6Kbit prio 8 maxburst 20 avpkt 1000tc class add dev eth1 parent 10:1 classid 10:100 cbq bandwidth 64Kbit rate \
32Kbit allot 1514 weight 3Kbit prio 5 maxburst 20 avpkt 100 boundedtc qdisc add dev eth1 parent 10:100 sfq quantum 1514b perturb 15
tc filter add dev eth1 protocol ip parent 10:1 prio 100 handle 1 fw classid 1:100
Regards
- Jaco van der Schyff
[email protected]+27 12 803 7591 +27 12 803 7285 (f) +27 83 680 4922 (mobile) f6e2eb48937f22e159a408c84533cdcbQuoted 18 lines · Ramin Alidousti
what is/are your setup/rules? It should work just fine.
Ramin
Quoted 11 lines · Jaco van der Schyff
Greetings earthlings,
I am batteling to get NATted packets marked with iptables, to shape them later using the fw filter.
Has anyone tried to mark packets that are masqueraded, or to shape masqueraded connections?
It doesn't seem to work.
If any knows what to do, please help.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
I had ever met this condition
I change chain rule at iptables,try like this
iptables -I OUTPUT -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK --set-mark 1
and it works.
Regards
Johan
Quoted 80 lines · Ramin Alidousti
I assume that the packets come in on eth0, right? And I'm not sure if the mangle table sees the destination as 192.168.62.0/24 or as the original destination address. Try this:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d 192.168.62.0/24 \ -j MARK --set-mark 1If it doesn't work, try:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d <orig dst IP's>
-j MARK --set-mark 1Hope it works,
RaminQuoted 40 lines · Jaco van der Schyff
I removed the comments from the file below, also this isnt the complete file, but it should be enough to give you an idea what I want to acheive.
iptables -A PREROUTING -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK \
--set-mark 1tc qdisc add dev eth1 root handle 10: cbq bandwidth 64Kbit avpkt 1000
tc class add dev eth1 parent 10:0 classid 10:1 cbq bandwidth 64Kbit rate \
64Kbit allot 1514 weight 6Kbit prio 8 maxburst 20 avpkt 1000tc class add dev eth1 parent 10:1 classid 10:100 cbq bandwidth 64Kbit rate \
32Kbit allot 1514 weight 3Kbit prio 5 maxburst 20 avpkt 100 boundedtc qdisc add dev eth1 parent 10:100 sfq quantum 1514b perturb 15
tc filter add dev eth1 protocol ip parent 10:1 prio 100 handle 1 fw classid 1:100
Regards
- Jaco van der Schyff
[email protected]+27 12 803 7591 +27 12 803 7285 (f) +27 83 680 4922 (mobile) f6e2eb48937f22e159a408c84533cdcbQuoted 19 lines
Quoted 18 lines · Ramin Alidousti
what is/are your setup/rules? It should work just fine.
Ramin
Quoted 11 lines · Jaco van der Schyff
Greetings earthlings,
I am batteling to get NATted packets marked with iptables, to shape them later using the fw filter.
Has anyone tried to mark packets that are masqueraded, or to shape masqueraded connections?
It doesn't seem to work.
If any knows what to do, please help.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Signature · 11 lines
-'-
(o o)
---------ooO--(_)--Ooo-------------------------------------------------
( )/ \( )( ) ( ) ( \( ) Visit us at http://www.pinguind.co.id
__)(( () ))__( /__\ ) ( Feel free to contact me at ICQ #47240718
(___/ \__/(_)(_)(_)(_)(_)\_) email:[email protected]
-----------------------------------------------------------------------
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/Aren't you making any mistake here, Johan? OUTPUT chain is meant for the outgoing packets from the firewall itself. What Jaco is doing is receiving packets from the network which will never pass the OUTPUT chain.
Ramin
Quoted 6 lines · On Thu, May 17, 2001 at 06:29:00AM -0400, [email protected] wrote:
I had ever met this condition
I change chain rule at iptables,try like thisiptables -I OUTPUT -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK --set-mark 1
Quoted 21 lines
and it works.
Regards
Johan
Quoted 14 lines · Ramin Alidousti
I assume that the packets come in on eth0, right? And I'm not sure if the mangle table sees the destination as 192.168.62.0/24 or as the original destination address. Try this:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d 192.168.62.0/24 \ -j MARK --set-mark 1If it doesn't work, try:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d <orig dst IP's>
-j MARK --set-mark 1Hope it works,
Ramin
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
No..
I had proved that
My configuration works well
I think CBQ stack below the iptables stack program, and
almost 'stay at' layer 2 networking.
had you proved with OUTPUT chain to limit bandwidth ?
cause, I had tried when limit with PREROUTING chain, the result is not satisfied.
Johan
Quoted 36 lines · Ramin Alidousti
Aren't you making any mistake here, Johan? OUTPUT chain is meant for the outgoing packets from the firewall itself. What Jaco is doing is receiving packets from the network which will never pass the OUTPUT chain.
Ramin
Quoted 27 lines · On Thu, May 17, 2001 at 06:29:00AM -0400, [email protected] wrote:
I had ever met this condition
I change chain rule at iptables,try like thisiptables -I OUTPUT -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK --set-mark 1
and it works.
Regards
Johan
Quoted 14 lines · Ramin Alidousti
I assume that the packets come in on eth0, right? And I'm not sure if the mangle table sees the destination as 192.168.62.0/24 or as the original destination address. Try this:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d 192.168.62.0/24 \ -j MARK --set-mark 1If it doesn't work, try:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d <orig dst IP's>
-j MARK --set-mark 1Hope it works,
Ramin
Signature · 11 lines
-'-
(o o)
---------ooO--(_)--Ooo-------------------------------------------------
( )/ \( )( ) ( ) ( \( ) Visit us at http://www.pinguind.co.id
__)(( () ))__( /__\ ) ( Feel free to contact me at ICQ #47240718
(___/ \__/(_)(_)(_)(_)(_)\_) email:[email protected]
-----------------------------------------------------------------------
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/This is the result when I use with OUTPUT chain
150 Opening BINARY mode data connection for iproute-2.2.4-2.i386.rpm (327439 bytes).
226 Transfer complete.
327439 bytes received in 21 secs (15 Kbytes/sec)
With configuration like this
bash# iptables -t mangle -L
Chain PREROUTING (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination MARK tcp -- fvbs.pinguind.co.id anywhere state RELATED,ESTABLISHED MARK set 0x1 MARK tcp -- fvbs.pinguind.co.id anywhere tcp spt:www MARK set 0x2
---[ eth0: configured classes ]---------------------------
class cbq 10: root rate 10Mbit (bounded,isolated) prio no-transmit class cbq 10:2 parent 10: rate 10Mbit prio 4
class cbq 10:4 parent 10:2 leaf 8001: rate 128Kbit prio 4 class cbq 10:5 parent 10:2 leaf 8002: rate 256Kbit prio 4
---[ eth0: queueing disciplines ]-------------------------
qdisc tbf 8002: rate 256Kbit burst 10Kb lat 190.7ms qdisc tbf 8001: rate 128Kbit burst 10Kb lat 381.5ms qdisc cbq 10: rate 10Mbit (bounded,isolated) prio no-transmit
Quoted 36 lines · Ramin Alidousti
Aren't you making any mistake here, Johan? OUTPUT chain is meant for the outgoing packets from the firewall itself. What Jaco is doing is receiving packets from the network which will never pass the OUTPUT chain.
Ramin
Quoted 27 lines · On Thu, May 17, 2001 at 06:29:00AM -0400, [email protected] wrote:
I had ever met this condition
I change chain rule at iptables,try like thisiptables -I OUTPUT -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK --set-mark 1
and it works.
Regards
Johan
Quoted 14 lines · Ramin Alidousti
I assume that the packets come in on eth0, right? And I'm not sure if the mangle table sees the destination as 192.168.62.0/24 or as the original destination address. Try this:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d 192.168.62.0/24 \ -j MARK --set-mark 1If it doesn't work, try:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d <orig dst IP's>
-j MARK --set-mark 1Hope it works,
Ramin
Signature · 11 lines
-'-
(o o)
---------ooO--(_)--Ooo-------------------------------------------------
( )/ \( )( ) ( ) ( \( ) Visit us at http://www.pinguind.co.id
__)(( () ))__( /__\ ) ( Feel free to contact me at ICQ #47240718
(___/ \__/(_)(_)(_)(_)(_)\_) email:[email protected]
-----------------------------------------------------------------------
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/OK. My question is: where are you doing the ftp from?
1) When you use OUTPUT the packets originating from your firewall will be marked.
2) When you use INPUT the packets destined for your firewall will be marked. (you don't use this because it's too late for tc).
3) When you use PREROUTING the packets received from the network will be marked.
4) When you use POSTROUTING the packets leaving your firewall will be marked. (you don't use this because it's too late for tc).
It all depends on your application, what you want to mark, in which direction and where in the forwarding process.
Ramin
Quoted 82 lines · On Thu, May 17, 2001 at 05:57:35PM -0400, [email protected] wrote:
This is the result when I use with OUTPUT chain
150 Opening BINARY mode data connection for iproute-2.2.4-2.i386.rpm (327439 bytes).
226 Transfer complete.
327439 bytes received in 21 secs (15 Kbytes/sec)With configuration like this
bash# iptables -t mangle -L
Chain PREROUTING (policy ACCEPT)
target prot opt source destinationChain OUTPUT (policy ACCEPT)
target prot opt source destination MARK tcp -- fvbs.pinguind.co.id anywhere state RELATED,ESTABLISHED MARK set 0x1 MARK tcp -- fvbs.pinguind.co.id anywhere tcp spt:www MARK set 0x2---[ eth0: configured classes ]---------------------------
class cbq 10: root rate 10Mbit (bounded,isolated) prio no-transmit class cbq 10:2 parent 10: rate 10Mbit prio 4
class cbq 10:4 parent 10:2 leaf 8001: rate 128Kbit prio 4 class cbq 10:5 parent 10:2 leaf 8002: rate 256Kbit prio 4---[ eth0: queueing disciplines ]-------------------------
qdisc tbf 8002: rate 256Kbit burst 10Kb lat 190.7ms qdisc tbf 8001: rate 128Kbit burst 10Kb lat 381.5ms qdisc cbq 10: rate 10Mbit (bounded,isolated) prio no-transmit
Quoted 36 lines · Ramin Alidousti
Aren't you making any mistake here, Johan? OUTPUT chain is meant for the outgoing packets from the firewall itself. What Jaco is doing is receiving packets from the network which will never pass the OUTPUT chain.
Ramin
Quoted 27 lines · On Thu, May 17, 2001 at 06:29:00AM -0400, [email protected] wrote:
I had ever met this condition
I change chain rule at iptables,try like thisiptables -I OUTPUT -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK --set-mark 1
and it works.
Regards
Johan
Quoted 14 lines · Ramin Alidousti
I assume that the packets come in on eth0, right? And I'm not sure if the mangle table sees the destination as 192.168.62.0/24 or as the original destination address. Try this:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d 192.168.62.0/24 \ -j MARK --set-mark 1If it doesn't work, try:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d <orig dst IP's>
-j MARK --set-mark 1Hope it works,
RaminSignature · 11 lines
-'- (o o) ---------ooO--(_)--Ooo------------------------------------------------- ( )/ \( )( ) ( ) ( \( ) Visit us at http://www.pinguind.co.id __)(( () ))__( /__\ ) ( Feel free to contact me at ICQ #47240718 (___/ \__/(_)(_)(_)(_)(_)\_) email:[email protected] ----------------------------------------------------------------------- _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Signature · 7 lines
Ramin Alidousti [email protected] Advanced Development tel +1 703 886 2640 UUNET, A WorldCom Company fax +1 703 886 0536 _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
I see,
I'm doing ftp from packets originating from my CBQ host (not firewall dual home, because I just have one interface card)
OK, thanks for your "enlightenment"
my configuration works well in case of packets originating from my host. But my question,
Can we limit packets that originating from my CBQ host with using PREROUTING chain ?
thanks
Quoted 113 lines · Ramin Alidousti
OK. My question is: where are you doing the ftp from?
1) When you use OUTPUT the packets originating from your firewall will be marked.
2) When you use INPUT the packets destined for your firewall will be marked. (you don't use this because it's too late for tc).
3) When you use PREROUTING the packets received from the network will be marked.
4) When you use POSTROUTING the packets leaving your firewall will be marked. (you don't use this because it's too late for tc).It all depends on your application, what you want to mark, in which direction and where in the forwarding process.
Ramin
Quoted 82 lines · On Thu, May 17, 2001 at 05:57:35PM -0400, [email protected] wrote:
This is the result when I use with OUTPUT chain
150 Opening BINARY mode data connection for iproute-2.2.4-2.i386.rpm (327439 bytes).
226 Transfer complete.
327439 bytes received in 21 secs (15 Kbytes/sec)With configuration like this
bash# iptables -t mangle -L
Chain PREROUTING (policy ACCEPT)
target prot opt source destinationChain OUTPUT (policy ACCEPT)
target prot opt source destination MARK tcp -- fvbs.pinguind.co.id anywhere state RELATED,ESTABLISHED MARK set 0x1 MARK tcp -- fvbs.pinguind.co.id anywhere tcp spt:www MARK set 0x2---[ eth0: configured classes ]---------------------------
class cbq 10: root rate 10Mbit (bounded,isolated) prio no-transmit class cbq 10:2 parent 10: rate 10Mbit prio 4
class cbq 10:4 parent 10:2 leaf 8001: rate 128Kbit prio 4 class cbq 10:5 parent 10:2 leaf 8002: rate 256Kbit prio 4---[ eth0: queueing disciplines ]-------------------------
qdisc tbf 8002: rate 256Kbit burst 10Kb lat 190.7ms qdisc tbf 8001: rate 128Kbit burst 10Kb lat 381.5ms qdisc cbq 10: rate 10Mbit (bounded,isolated) prio no-transmit
Quoted 36 lines · Ramin Alidousti
Aren't you making any mistake here, Johan? OUTPUT chain is meant for the outgoing packets from the firewall itself. What Jaco is doing is receiving packets from the network which will never pass the OUTPUT chain.
Ramin
Quoted 27 lines · On Thu, May 17, 2001 at 06:29:00AM -0400, [email protected] wrote:
I had ever met this condition
I change chain rule at iptables,try like thisiptables -I OUTPUT -t mangle -p tcp -s 0/0 -d 192.168.62.0/24 -j MARK --set-mark 1
and it works.
Regards
Johan
Quoted 14 lines · Ramin Alidousti
I assume that the packets come in on eth0, right? And I'm not sure if the mangle table sees the destination as 192.168.62.0/24 or as the original destination address. Try this:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d 192.168.62.0/24 \ -j MARK --set-mark 1If it doesn't work, try:
iptables -A PREROUTING -t mangle -p tcp -i eth0 -d <orig dst IP's>
-j MARK --set-mark 1Hope it works,
RaminSignature · 11 lines
-'- (o o) ---------ooO--(_)--Ooo------------------------------------------------- ( )/ \( )( ) ( ) ( \( ) Visit us at http://www.pinguind.co.id __)(( () ))__( /__\ ) ( Feel free to contact me at ICQ #47240718 (___/ \__/(_)(_)(_)(_)(_)\_) email:[email protected] ----------------------------------------------------------------------- _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/Signature · 7 lines
Ramin Alidousti [email protected] Advanced Development tel +1 703 886 2640 UUNET, A WorldCom Company fax +1 703 886 0536 _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Signature · 11 lines
-'-
(o o)
---------ooO--(_)--Ooo-------------------------------------------------
( )/ \( )( ) ( ) ( \( ) Visit us at http://www.pinguind.co.id
__)(( () ))__( /__\ ) ( Feel free to contact me at ICQ #47240718
(___/ \__/(_)(_)(_)(_)(_)\_) email:[email protected]
-----------------------------------------------------------------------
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/Quoted 9 lines · On Thu, May 17, 2001 at 07:49:59PM -0400, [email protected] wrote:
I see,
I'm doing ftp from packets originating from my CBQ host (not firewall dual home, because I just have one interface card)
OK, thanks for your "enlightenment"
my configuration works well in case of packets originating from my host. But my question,Can we limit packets that originating from my CBQ host with using PREROUTING chain ?
No. In your case with OUTPUT chain.
Ramin
Quoted 2 lines
thanks
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Hi,
I think with the following rules you can get it done:
iptables -t mangle -I PREROUTING -s 192.168.1.0/24 -j MARK --set-mark 1 iptables -t nat -I POSTROUTING -s 192.168.1.0/24 -j SNAT --to-source 192.168.2.1
So each packet going through your router will first be marked if it comes from 192.168.1.0/24 (PREROUTING) and after routing and tc queuing it will be NATed (POSTROUTING).
That works for marking packets going out of your network through your NATing box.
To mark packets coming into your network, since mangle only has PREROUTING and OUTPUT, it could be done with this:
iptables -t mangle -I PREROUTING -s 192.168.2.1/32 -j MARK --set-mark 2
It marks the packets before they are deNATed, but works asuming that no traffic is comming directly to your NAT box, or these will be marked as well.
These examples seemed to work on a test router here (only I used marking TOS so I could watch it with tcpdump, outgoing packets marked with TOS 0x2 and incoming with TOS 0x4):
On client 192.168.1.99 made a "ping altavista.com -n -c 1". Router is 192.168.2.1 (there is other NAT after it, but doesn't affect it).
13:40:12.446406 eth1 < 192.168.1.99 > 209.73.180.2: icmp: echo request (DF) [tos 0x2,ECT] (ttl 64, id 0) 13:40:12.446440 eth0 > 192.168.2.1 > 209.73.180.2: icmp: echo request (DF) [tos 0x2,ECT] (ttl 63, id 0)
13:40:12.554895 eth0 < 209.73.180.2 > 192.168.1.99: icmp: echo reply [tos 0x4] (ttl 241, id 56493) 13:40:12.554916 eth1 > 209.73.180.2 > 192.168.1.99: icmp: echo reply [tos 0x4] (ttl 240, id 56493)
Hope this helps.
Cheers,
Rodrigo
Quoted 21 lines · Jaco van der Schyff
Greetings earthlings,
I am batteling to get NATted packets marked with iptables, to shape them later using the fw filter.
Has anyone tried to mark packets that are masqueraded, or to shape masqueraded connections?
It doesn't seem to work.
If any knows what to do, please help.
Regards
- Jaco van der Schyff
[email protected]+27 12 803 7591
+27 12 803 7285 (f)
+27 83 680 4922 (mobile)
Quoted 5 lines
f6e2eb48937f22e159a408c84533cdcb_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/