Three ethernet cards?
Hi,
I have a slight problem, is it possible to shape bandwidth over more than one interface.
I have a linux box with eth0 going to a cisco router, I want to shape bandwith to eth1 and eth2 eth1 goes to the lan, and eth2 to a DMZ.
How can I accomplish this, so that I can shape the same bandwith to the DMZ and the lan? (their bandwith should be shared) ?
/eth1 (to local LAN)
/
/
/
|-------------|
eth0 | |
----------- |
to | |
internet |-------------|
\
\
\
\ eth2 (to DMZ)btw. Thanks for all the help on my previous posts
- Jaco van der Schyff
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 2 lines · Jaco van der Schyff
I have a slight problem, is it possible to shape bandwidth over more than one interface.
Yes.
Quoted 9 lines
I have a linux box with eth0 going to a cisco router, I want to shape bandwith to eth1 and eth2 eth1 goes to the lan, and eth2 to a DMZ.
How can I accomplish this, so that I can shape the same bandwith to the DMZ and the lan? (their bandwith should be shared) ?
Quoted 14 lines
/eth1 (to local LAN)
/
/
/
|-------------|
eth0 | |
----------- |
to | |
internet |-------------|
\
\
\
\ eth2 (to DMZ)Just create seperate classes and queueing disciplines for each interface. And please read the example in the HOWTO, and try to ask more specific questions.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Ya !! sure it is possible to shape bandwidth on more than one interface. For e.g. in CBQ whenever u shape bandwidth i.e. when we apply the rules we also specify to what interface these rules are applied . So for each interface u have , u specify the bandwidth policy to be applied.
Deepak
----- Original Message -----
From: "Jaco van der Schyff" <[email protected]>
To: <[email protected]>
Sent: Monday, May 21, 2001 6:52 PM
Subject: [LARTC] Three ethernet cards?
Quoted 33 lines
Hi,
I have a slight problem, is it possible to shape bandwidth over more than one interface.
I have a linux box with eth0 going to a cisco router, I want to shape bandwith to eth1 and eth2 eth1 goes to the lan, and eth2 to a DMZ.
How can I accomplish this, so that I can shape the same bandwith to the DMZ and the lan? (their bandwith should be shared) ?
/eth1 (to local LAN) / / / |-------------| eth0 | | ----------- | to | | internet |-------------| \ \ \ \ eth2 (to DMZ)
Quoted 8 lines
btw. Thanks for all the help on my previous posts
- Jaco van der Schyff
[email protected]_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
Quoted 1 line
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
----- Original Message -----
From: "Vladimir Smelhaus" <[email protected]>
To: "Deepak singhal" <[email protected]>
Sent: Tuesday, May 22, 2001 10:58 AM
Subject: Re: [LARTC] Three ethernet cards?
Quoted 9 lines
Dne 22 May 2001, v 10:18, Deepak singhal napsal(a):
Quoted 5 lines
Ya !! sure it is possible to shape bandwidth on more than one interface. For e.g. in CBQ whenever u shape bandwidth i.e. when we apply the rules we also specify to what interface these rules are applied . So for each interface u have , u specify the bandwidth policy to be applied.
And what about to borrow bandwidth between three cards ?
As per my knowledge borrowing bandwidth between cards is not possible as a seperate Hierarchy would exist for each interface. Within a hierarchy borrowing/sharing bandwidth between classes is possible.
Deepak
Quoted 5 lines
Zdravim/Regards
Vladimir Smelhaus
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 4 lines
As per my knowledge borrowing bandwidth between cards is not possible as a seperate Hierarchy would exist for each interface. Within a hierarchy borrowing/sharing bandwidth between classes is possible.
iow, It is not possible, to shape the incoming bandwith out to two networks on sperate NICs?
- Jaco
Quoted 15 lines · Deepak singhal
----- Original Message -----
From: "Vladimir Smelhaus" <[email protected]>
To: "Deepak singhal" <[email protected]>
Sent: Tuesday, May 22, 2001 10:58 AM
Subject: Re: [LARTC] Three ethernet cards?Quoted 8 lines
Dne 22 May 2001, v 10:18, Deepak singhal napsal(a):
Quoted 5 lines
Ya !! sure it is possible to shape bandwidth on more than one interface. For e.g. in CBQ whenever u shape bandwidth i.e. when we apply the rules we also specify to what interface these rules are applied . So for each interface u have , u specify the bandwidth policy to be applied.
Quoted 13 lines
Quoted 1 line
And what about to borrow bandwidth between three cards ?
As per my knowledge borrowing bandwidth between cards is not possible as a seperate Hierarchy would exist for each interface. Within a hierarchy borrowing/sharing bandwidth between classes is possible.
Deepak
Quoted 5 lines
Zdravim/Regards
Vladimir Smelhaus
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/