Asm error when building cross-compiler

Hi all,

I figure people on this list have experience with compiling cross-compilers with IA64 as the target. If there is a more appropriate place to ask, let me know.

I downloaded the toolchain linked from the ia64linux.org page:
ftp://ftp.cygnus.com/private/intel/

When building it, I run in to the following:

cp ../../gcc/config/ia64/lib1funcs.asm libgcc1.S
for name in __divdf3 __divsf3 __divdi3 __moddi3 __udivdi3 __umoddi3 __divsi3 __modsi3 __udivsi3 __umodsi3 __save_stack_nonlocal __nonlocal_goto __restore_stack_nonlocal; \
do \
echo ${name}; \
/home/lofgren/work/ia64_toolchain/build/gcc/xgcc -B/home/lofgren/work/ia64_toolchain/build/gcc/ -B/usr/local/ia64/ia64-hp-linux-gnu/bin/ -I/usr/local/ia64/ia64-hp-linux-gnu/include -O2 -DCROSS_COMPILE -DIN_GCC -g -O2 -I./include -fPIC -g1 -DIN_LIBGCC2 -D__GCC_FLOAT_NOT_NEEDED -I. -I../../gcc -I../../gcc/config -I../../gcc/../include -c -DL${name} libgcc1.S; \
if [ $? -eq 0 ] ; then true; else exit 1; fi; \
mv libgcc1.o ${name}.o; \
/home/lofgren/work/ia64_toolchain/build/binutils/ar rc tmplibgcc1.a ${name}.o; \
rm -f ${name}.o; \
done
__divdf3
__divsf3
__divdi3
__moddi3
__udivdi3
__umoddi3
__divsi3
__modsi3
__udivsi3
__umodsi3
__save_stack_nonlocal
__nonlocal_goto
libgcc1.S: Assembler messages:
libgcc1.S:604: Error: Unknown opcode `mov.ret.sptk.few.dc.dc rp=r33,.L0'
make[1]: *** [libgcc1-asm.a] Error 1
make[1]: Leaving directory `/home/lofgren/work/ia64_toolchain/build/gcc'
make: *** [all-gcc] Error 2

As far as I see, the instruction is valid. I tried removing the .dc.dc completers, since they're deprecated, but it still fails. Any ideas?

All other tools (bfd, binutils, gdb, gas, ld, ...) appeared to have been built flawlessly.

Thanks,
Tom Lofgren

T. Lofgren <[email protected]>: Wherever I lay my .emacs, that's my ${HOME}
PGP Key ID: DC68D8F6                  Encryption is the envelope for email

You have a mismatched assembler and compiler. I'm not sure how you could have done that if everything you are using is from the toolchain downloaded from ftp.cygnus.com. If you have any assembler newer than the one in the February release then it would fail this way, because this problem was fixed shortly after the February release.

Do you perhaps already have a new assembler in /usr/local/ia64/ia64-hp-linux-gnu/bin? If so, then that could explain the problem. The -B options in the makefiles are in the wrong order, so if you try build on top of an existing toolchain then this problem can happen.

The instruction in question is not valid because the .dc.dc and .few completers were removed from the architecture. If you have a new assembler, and you remove both, then it should work. Though you may have other problems if you aren't using the assembler that came with this compiler. C++ EH for instance won't work, and there might be problems with shared libraries.

Jim