Skip to contentSkip to conversation

ia64_get_dcr problem

Linux-ia64 Jack Steiner 3 participants 3 messages Feb 12, 2001

lore
Share & tools
lore
#0 lore raw

Is this a GCC problem or a problem with the asm/ia64/processor.h inline functions??

I used the ia64_set_dcr & ia64_get_dcr functions in
a loop & got bad code. I had references to both ia64_get_dcr in ia64_set_dcr in the loop. The "get" was optimized out of the loop & did not see the result of the "set".

If I add "volatile" to the ia64_get_dcr asm statement, I can avoid the problem. But I am not sure whether this is the correct solution. (I hit a similar problem with ia64_get_irr0() earlier too).

I am using the "2.96-ia64-000717 snap 001117" compiler.

Source (stupid test but illustrates the problem):

        void
        dcrtest() {

                long    i, dcr;
                for (i=0; i<10; i++) {
                        printk("0x%lx\n", ia64_get_dcr());
                        ia64_set_dcr(0x5555);
                }
        }

Generated code:

         <dcrtest.0>        alloc r36=ar.pfs,0,5,2,0  
         <dcrtest.1>        mov r34=cr.dcr                      <<< get
         <dcrtest.2>        mov r35=rp  
         <dcrtest+0x10.0>        mov r33!845  
         <dcrtest+0x10.1>        mov r32=9  
         <dcrtest+0x10.2>        nop.i 0  
         <dcrtest+0x20.0>        addl r37=-1091248,gp;;
         <dcrtest+0x20.1>        mov r38=r34  
         <dcrtest+0x20.2>        nop.i 0  
         <dcrtest+0x30.0>        ld8 r37=[r37]  
         <dcrtest+0x30.1>        nop.i 0  
         <dcrtest+0x30.2>        br.call.sptk.many rp=printk;;
         <dcrtest+0x40.0>        mov cr.dcr=r33;;               <<< set
         <dcrtest+0x40.1>        srlz.d  
         <dcrtest+0x40.2>        adds r32=-1,r32;;
         <dcrtest+0x50.0>        cmp.lt p7,p6=r32,r0  
         <dcrtest+0x50.1>        nop.i 0  
         <dcrtest+0x50.2>   (p6) br.cond.dptk.few dcrtest+0x20  

         <dcrtest+0x60.0>        nop.m 0  
         <dcrtest+0x60.1>        mov.i ar.pfs=r36  
         <dcrtest+0x60.2>        mov rp=r35  
         <dcrtest+0x70.0>        nop.m 0  
         <dcrtest+0x70.1>        nop.i 0  
         <dcrtest+0x70.2>        br.ret.sptk.many rp;;
Signature · 3 lines
Thanks

Jack Steiner    (651-683-5302)   (vnet 233-5302)      [email protected]
#1 lore raw

It is a kernel problem. Your testcase can not work as intended without the volatile in the definition of ia64_get_dcr. It looks like the kernel doesn't actually use ia64_get_dcr, which is why the problem wasn't noticed before.

Jim

#2 lore raw
In reply to Jack Steiner
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line · Jack Steiner

Jack> Is this a GCC problem or a problem with the Jack> asm/ia64/processor.h inline functions??

Jack> I used the ia64_set_dcr & ia64_get_dcr functions in a loop & Jack> got bad code. I had references to both ia64_get_dcr in Jack> ia64_set_dcr in the loop. The "get" was optimized out of the Jack> loop & did not see the result of the "set".

Jack> If I add "volatile" to the ia64_get_dcr asm statement, I can Jack> avoid the problem. But I am not sure whether this is the Jack> correct solution. (I hit a similar problem with Jack> ia64_get_irr0() earlier too).

Thanks for the report.

I fixed this now, along with a couple of other *get* macros in processor.h.

	--david