AWE32 initialization wiht isapnp
Hello,
In order to use the wavetable device of my AWE32 I was starting under MSDOS, executing ctpnp to configure the card and then I was running loadlin and the Wavetable was properly detected.
However I only want to use lilo, so I'm using isapnp to configure the awe32 (audio and wavetable) and then I "modprobe" sound module. Then the audio device (dsp, opl2/3) is correclty detected, but the AWE32 Wavetable on port 0x620 is not detected (according to /proc/ioports).
Can someone help me please ?
---
Alexis Domjan <[email protected]>
Quoted 8 lines · Alexis DOMJAN
In order to use the wavetable device of my AWE32 I was starting under MSDOS, executing ctpnp to configure the card and then I was running loadlin and the Wavetable was properly detected.
However I only want to use lilo, so I'm using isapnp to configure the awe32 (audio and wavetable) and then I "modprobe" sound module. Then the audio device (dsp, opl2/3) is correclty detected, but the AWE32 Wavetable on port
0x620is not detected (according to/proc/ioports).
Find the line in your isapnp.conf file that says:
(IO 0 (BASE 0x0620))
Add right after it:
(IO 1 (BASE 0x0A20)) (IO 2 (BASE 0x0E20))
pnpdump, for whatever reason, doesn't see all the IO ports for the EMU chip on the AWE.
Bill
Hi!
By the way, how do I enable the midi device?
I have a SB 32 Plug & Play, and it is working fine, except for the midi. My /dev/sndstat file is as follows:
-----Begin------
Sound Driver:3.5.4-960630
Kernel: Linux replicant.dei.uc.pt 2.0.35 #1 Thu Sep 24 21:11:57 WEST 1998 i586
Config options: 0
Installed drivers:
Card config:
Audio devices:
0: Sound Blaster 16 (4.13)
Synth devices:
0: Yamaha OPL-3
1: AWE32-0.4.2d (RAM0k)
Midi devices:
Timers:
0: System clock
Mixers:
0: Sound Blaster
1: AWE32 Equalizer
-------End-------
I have kernel 2.0.35 compiled with midi support (as you can see).
Thanks!
-----------------------------------------------------------------------------
Ricardo Peres
E-mail: [email protected]
ICQ UIN: 708926
TM: 0931 9459192
Departamento de Engenharia Informática
Universidade de Coimbra
PORTUGAL
-----------------------------------------------------------------------------
Quoted 23 lines · Bill Nottingham
Quoted 8 lines · Alexis DOMJAN
In order to use the wavetable device of my AWE32 I was starting under MSDOS, executing ctpnp to configure the card and then I was running loadlin and the Wavetable was properly detected.
However I only want to use lilo, so I'm using isapnp to configure the awe32 (audio and wavetable) and then I "modprobe" sound module. Then the audio device (dsp, opl2/3) is correclty detected, but the AWE32 Wavetable on port
0x620is not detected (according to/proc/ioports).Find the line in your isapnp.conf file that says:
(IO 0 (BASE 0x0620))Add right after it:
(IO 1 (BASE 0x0A20)) (IO 2 (BASE 0x0E20))pnpdump, for whatever reason, doesn't see all the IO ports for the EMU chip on the AWE.
Bill
Quoted 12 lines · Bill Nottingham
Quoted 8 lines · Alexis DOMJAN
In order to use the wavetable device of my AWE32 I was starting under MSDOS, executing ctpnp to configure the card and then I was running loadlin and the Wavetable was properly detected.
However I only want to use lilo, so I'm using isapnp to configure the awe32 (audio and wavetable) and then I "modprobe" sound module. Then the audio device (dsp, opl2/3) is correclty detected, but the AWE32 Wavetable on port
0x620is not detected (according to/proc/ioports).Find the line in your isapnp.conf file that says:
Quoted 8 lines
(IO 0 (BASE 0x0620))Add right after it:
(IO 1 (BASE 0x0A20)) (IO 2 (BASE 0x0E20))pnpdump, for whatever reason, doesn't see all the IO ports for the EMU chip on the AWE.
Her is an excerpt of my /etc/isapnp.conf
(CONFIGURE CTL0042/83463
(LD 3 # ANSI string -->WaveTable<-- (IO 0 (BASE 0x0620)) (IO 1 (BASE 0x0A20)) (IO 2 (BASE 0x0E20)) (ACT Y) )
)
But I still have the problem.
Quoted 2 lines
Bill
Quoted 34 lines · Ricardo Peres
Hi!
By the way, how do I enable the midi device?
I have a SB 32 Plug & Play, and it is working fine, except for the midi. My/dev/sndstatfile is as follows:-----Begin------
Sound Driver:3.5.4-960630
Kernel: Linux replicant.dei.uc.pt 2.0.35 #1 Thu Sep 24 21:11:57 WEST 1998 i586
Config options: 0Installed drivers:
Card config:
Audio devices:
0: Sound Blaster 16 (4.13)Synth devices:
0: Yamaha OPL-3
1: AWE32-0.4.2d (RAM0k)Midi devices:
Timers:
0: System clockMixers:
0: Sound Blaster
1: AWE32 Equalizer
Quoted 6 lines
-------End-------
I have kernel 2.0.35 compiled with midi support (as you can see).
Thanks!
...
Hello,
On my 2.0.33 system the midi devices get recognized,
but no bytes are leaving the sound card via the midi bus. I have an AWE 64 Gold here.
Does anybody know of such problems with AWE cards or has anybody midi output
to externals synths running under Linux ?
The output of /dev/sndstat here is the following:
-------------------------
---OSS/Free3.8s9-980302 (Thu Aug 27 21:36:00 CEST 1998 root, Linux esqhen 2.0.33 #6 Tue May 5 21:52:30 CEST 1998 i586 unknown) Load type: Driver loaded as a module.
Kernel: Linux esqhen 2.0.33 #6 Tue May 5 21:52:30 CEST 1998 i586 Config options: 0
Installed drivers:
Type 26: MPU-401 (UART)
Type 2: Sound Blaster
Type 29: Sound Blaster PnP
Type 7: SB MPU-401
Card config:
Sound Blaster at 0x220 irq 5 drq 1,5
SB MPU-401 at 0x330 irq 5 drq 0
Audio devices:
0: Sound Blaster 16 (4.16)
Synth devices:
0: AWE32-0.4.2d (RAM4096k)
Midi devices:
0: Sound Blaster 16
Timers:
0: System clock
Mixers:
0: Sound Blaster
1: AWE32 Equalizer
------------------------------
Bye, Emil.
Signature · 5 lines
-------------------------------------------------- Emil Stephan, Marktplatz 39, 53773 Hennef, Germany voice: +49-2242-84438 Accelerate Windows: 9.81 m/sec^2 would be adequate