Skip to contentSkip to conversation

mp3's not playing?

DISCUSSION Keith Duthie 3 participants 4 messages Feb 16, 1999 – Feb 17, 1999 Sound

lore
Share & tools
lore
#0 lore raw
Quoted 3 lines · Rodrigo Castro

I have exactly the same problem as this guy. In my case, I have a SB32 PnP.

Any idea?

Yes

Quoted 2 lines

P.S.: I put a SB16 non-PnP to test and it worked really fine. I guess the problem is in PnP, am I right?

Perhaps. OTOH, I doubt it.

Quoted 6 lines
Quoted 6 lines

I boot, isapnp loads and says it's configuring the card for dma's 1,5 and irq5... then, I load the following modules as such...

/sbin/insmod sb io=0x220 irq=5 dma=1 mpu_io=0x330

Sound: DMA (output) timed out - IRQ/DRQ config error?

Read the excerpts. It reads like the other guy is a moron. Try adding in dma16=5 (or dma2=5 whichever the sb driver uses). That sounds like (one of) the problem(s).

Besides which, the options should be in the /etc/modules.conf file. And another thing: I believe the mpu should have an irq option, eg mpu_irq=9 (or mpuirq=9, whichever name the soundblaster uses)

If you use RedHat, then try the sndconfig utility. It doesn't work for me, but it may work for you.

Signature · 1 line
.sig under deconstruction. Please watch out for falling stars.
#1 lore raw

I have exactly the same problem as this guy. In my case, I have a SB32 PnP.

Any idea?

P.S.: I put a SB16 non-PnP to test and it worked really fine. I guess the problem is in PnP, am I right?

Well, that's it
Rodrigo Castro <[email protected]>
Computer Science undergraduate student at University of São Paulo

Quoted 70 lines · Scott Olsson - scohop

I have a soundblaster 16 plug and play card that has been giving me the fits. I've tried everything (well, almost... everything except what will eventually work...) to no avail. Below, I outlined how I've been going at this... if you have a similar card, please correct whatever ignorant greenie mistake I'm surely making/looking over... thanks!!

I boot, isapnp loads and says it's configuring the card for dma's 1,5 and irq5... then, I load the following modules as such...
----
/sbin/insmod soundcore
/sbin/insmod sound
/sbin/insmod uart401
/sbin/insmod sb io=0x220 irq=5 dma=1 mpu_io=0x330 /sbin/insmod opl3 io=0x388
---
Below, I cat'd my /dev/sndstat for reference... I don't really understand how some of it applies, but I'm assuming something should be listed under "installed drivers"... (???)
----

OSS/Free:3.8s2++-971130
Load type: Driver loaded as a module
Kernel: Linux .csh.uiuc.edu 2.2.1 #13 Mon Feb 15 15:09:11 EST 1999 i686 Config options: 0

Installed drivers:

Card config:

Audio devices:
0: Sound Blaster 16 (4.13)

Synth devices:
0: Yamaha OPL3

Midi devices:
0: Sound Blaster 16

Timers:
0: System clock

Mixers:
0: Sound Blaster

----

After the modules are all (??) loaded, I cat an au file to /dev/dsp or /dev/audio and it will play fine, but mp3's will not play through any of the players I have tried... (x11amp, freeamp, amp, xaudio, mpg123, newplayer)

when I've tried with an mp3player like newplayer it complains about dma problems with the following error message...

Sound: DMA (output) timed out - IRQ/DRQ config error?

Is there a specific procedure or some other driver/module that needs to be configured and/or loaded before mp3's/wav's will play? Also, where (script, etc) can I add the modules to load them every boot?

Any help will be very VERY... umm, helpful?
THANKS!!!

scott olsson

-- please email your response as welll... thanks again.

--
Scott Olsson - scohop
[email protected]

#2 lore raw
In reply to Keith Duthie
Quoted 5 lines · Keith Duthie
Quoted 2 lines · Rodrigo Castro
Quoted 2 lines

I boot, isapnp loads and says it's configuring the card for dma's 1,5 and irq5... then, I load the following modules as such...

Quoted 8 lines
Quoted 3 lines
Quoted 3 lines

/sbin/insmod sb io=0x220 irq=5 dma=1 mpu_io=0x330

Sound: DMA (output) timed out - IRQ/DRQ config error?

Read the excerpts. It reads like the other guy is a moron. Try adding in dma16=5 (or dma2=5 whichever the sb driver uses). That sounds like (one of) the problem(s).

Oh, I forget mentioning that but I already have dma16=5. That's not the problem. Maybe the guy who wrote the message I fowarded have forgetten but I haven't.

Quoted 4 lines

Besides which, the options should be in the /etc/modules.conf file. And another thing: I believe the mpu should have an irq option, eg mpu_irq=9 (or mpuirq=9, whichever name the soundblaster uses)

No. MPU does not need IRQ when we are talking about Sound Blaster cards. The configuration, in compilation (of kernel or modules), must be filled with -1 when using SB cards.

Quoted 2 lines

If you use RedHat, then try the sndconfig utility. It doesn't work for me, but it may work for you.

I use Debian distro.

Thank you anyway! ;-)
Rodrigo Castro <[email protected]>
Computer Science undergraduate student - University of Sao Paulo Rudeness is a weak man's imitation of strength.

#3 lore raw
In reply to Keith Duthie
Quoted 3 lines · Rodrigo Castro

Oh, I forget mentioning that but I already have dma16=5. That's not the problem. Maybe the guy who wrote the message I fowarded have forgetten but I haven't.

Aaargh! Try this :
cat /etc/isapnp.conf | grep -v ^# >tmp.file
cat /etc/modules.conf >>tmp.file
cat tmp.file | mail -s aaargh -c [email protected] [email protected]

caviat: I'm not entirely sure the mail command will work as advertised, but OTOH it should.

Quoted 8 lines
Quoted 4 lines

Besides which, the options should be in the /etc/modules.conf file. And another thing: I believe the mpu should have an irq option, eg mpu_irq=9 (or mpuirq=9, whichever name the soundblaster uses)

No. MPU does not need IRQ when we are talking about Sound Blaster cards. The configuration, in compilation (of kernel or modules), must be filled with -1 when using SB cards.

*SHRUG* That's a sb peculiarity, then.

Quoted 4 lines
Quoted 2 lines

If you use RedHat, then try the sndconfig utility. It doesn't work for me, but it may work for you.

I use Debian distro.

And I use Slackware (which explains why sndconfig doesn't work for me).

Signature · 1 line
.sig under deconstruction. Please watch out for falling stars.