Can't get AZT1008 sound card to work under RH6.0
Hello,
I just installed RH6.0 on my HP Vectra computer (which runs NT 4.0SP4).
I'm having problems getting my sound card working. I ran "sndconfig", and it found the ISA-PnP card, and (I assume) it ran "pnpdump" to dump the sound card's PnP info to a file. Then (I assume) it ran "isapnp" on the configuration file it created, which produced an error message. At that point, "sndconfig" wants me to select my sound card manually. This is the point where I think that things start going from bad to worse. I stared at the isapnp.conf file (as it now was), and editted it such that "isapnp" was happy with it (no error messages). Now, when I try and load the sound module (whichever one was left configured from "sndconfig" program), it seems to work for the OPL-3 part of the sound driver, but the other parts claim that the ports are already in use????
Can someone help me out here? I can provide details with a little rebooting and moving of data files without too much trouble.
AFAIK, HP has OEMed an Aztech sound card which uses the AZT 2320 chipset. NT claims it is an Aztech Pro 16V-A PnP card, but Aztech lists no such card on its WWW site. It does list a couple of cards which use the AZT2320 chipset, and only one of those is an ISA card. (Should I assume they are the same card????)
The big question is what addresses to use for which ioports. The answers seems to be 0x220, 0x534, IRQ 5, and DMA 0 and 1 for NT.
The isapnp.conf file looks like (simplified):
AZT1008 PnP Sound Device
LD 0 IDE CDROM DISABLED
IO 0 BASE 0x530 IO 1 BASE 0x330 LD 1 AUDIO IO 0 BASE 0x220
(do I want more than 1 IO device here???? IO 1 0x388?? IO 2 0x534 ???)
INT 0 IRQ 5 MODE +E
DMA 0 CHANNEL 0
DMA 1 CHANNEL 1
(I commented out an "extra" INT 0 IRQ 5 line under this LD [but different dependent function] which was causing an error when the file was being loaded at boot time!)
LD 2 MPU401 MIDI
(nothing defined here! I assume I want IO 0 0x330, IRQ 9???)
LD 3 GAME PORT
(again, nothing defined here! I assume I want IO 0 0x200???)
The sound module (/etc/conf.modules) thinks it is loading an Aztech Sound Galaxy driver. Is this right???? The Aztech source code seems to think so!
Is my configuration correct? If so, why won't the sound driver work?? Have I chosen the right sound driver? If not, what should it be???
I can forward my exact configuration and my exact messages if someone wants to help me. Thanks!
I'm hoping that there is a SIMPLE solution for this mess!
(I'm stuck on a crappy NT box using Outhouse until I get my Linux config straightened out!)
Kevin J. Cummings
[email protected]
Quoted 12 lines · Kevin
I'm having problems getting my sound card working. I ran "sndconfig", and it found the ISA-PnP card, and (I assume) it ran "pnpdump" to dump the sound card's PnP info to a file. Then (I assume) it ran "isapnp" on the configuration file it created, which produced an error message. At that point, "sndconfig" wants me to select my sound card manually. This is the point where I think that things start going from bad to worse. I stared at the isapnp.conf file (as it now was), and editted it such that "isapnp" was happy with it (no error messages). Now, when I try and load the sound module (whichever one was left configured from "sndconfig" program), it seems to work for the OPL-3 part of the sound driver, but the other parts claim that the ports are already in use????
Quoted 2 lines
Can someone help me out here? I can provide details with a little rebooting and moving
of data files without too much trouble.
I can't help you with the pnp stuff, but you will need it working before even trying to use a sound driver.
Quoted 4 lines
AFAIK, HP has OEMed an Aztech sound card which uses the AZT 2320 chipset. NT claims it
is an Aztech Pro 16V-A PnP card, but Aztech lists no such card on its WWW site. It does list a couple of cards which use the AZT2320 chipset, and only one of those is an ISA card. (Should I assume they are the same card????)
the US aztech site used to have a nice listing of all FCC IDs of their cards complete with descriptions and drivers - i would start by looking it up there.
note that the sgalaxy driver was only tested on AZT2316 cards, I don't have any card with the 2320 to play with - it might still work if the chip is backward compatible.
[I received a few success reports with pnp cards, but i can't find any complete pnp configuration files in my archive right now]
Quoted 3 lines
The big question is what addresses to use for which ioports.
The answers seems to be0x220,0x534, IRQ 5, and DMA 0 and 1 for NT.
the ISA aztech cards i've seen could emulate:
(1) a SBPro using IO"0, IRQ=5
(2) a MSS/WSS - IOS0, IRQ (3) a OPL3 - IO88 (4) a MPU401 - IO30, IRQ=9
[the io io and irqs are some common defaults. see the dos tools (if any) for possible values]
Quoted 4 lines
The isapnp.conf file looks like (simplified):
AZT1008 PnP Sound Device
LD 0 IDE CDROM DISABLEDIO 0 BASE 0x530
WSS
Quoted 1 line
IO 1 BASE 0x330
MPU401
Quoted 2 lines
LD 1 AUDIO
IO 0 BASE 0x220
SBPro
Quoted 2 lines
(do I want more than 1 IO device here???? IO 1
0x388?? IO 20x534???)
INT 0 IRQ 5 MODE +E
SBPro irq
Quoted 2 lines
DMA 0 CHANNEL 0
DMA 1 CHANNEL 1
WSS (and sbpro) dma
Quoted 5 lines
(I commented out an "extra" INT 0 IRQ 5 line under this LD [but different dependent function]
which was causing an error when the file was being loaded at boot time!)
LD 2 MPU401 MIDI
(nothing defined here! I assume I want IO 00x330, IRQ 9???)
unless the card has a wavetable module, or you want to connect external synths you won't need this.
Quoted 2 lines
LD 3 GAME PORT
(again, nothing defined here! I assume I want IO 00x200???)
ditto, unless you want use a joystick :)
note that the card probably needs two irqs - one for sbpro and one for wss. IIRC you /could/ use the same irq line for the sbpro and wss (7).
Quoted 6 lines
The sound module (
/etc/conf.modules) thinks it is loading an Aztech Sound Galaxy driver. Is this right????
The Aztech source code seems to think so!Is my configuration correct? If so, why won't the sound driver work?? Have I chosen the right sound driver? If not, what should it be???
Even if you don't get the sgalacy driver working, you should be able to use the sbpro driver to get at least 8bit sound going.
Quoted 8 lines · Kevin
The isapnp.conf file looks like (simplified):
AZT1008 PnP Sound Device
LD 0 IDE CDROM DISABLEDIO 0 BASE 0x530 IO 1 BASE 0x330 LD 1 AUDIO IO 0 BASE 0x220(do I want more than 1 IO device here???? IO 1
0x388?? IO 20x534???)
That's odd - it has settings for 0x530/0x534 in both LD 0 and LD 1 - that doesn't seem right.
Quoted 2 lines
The sound module (
/etc/conf.modules) thinks it is loading an Aztech Sound Galaxy driver. Is this right???? The Aztech source code seems to think so!
That is the Sound Galaxy driver. Unfortunately, I've heard reports of it not working well with some SG cards - in those cases, no matter what you do, it seems unable to initialize the WSS compat. on the card; however, you should be able to at least get it to work in SBPro compatibility mode.
What does your isapnp.conf & conf.modules look like?
Bill