PCMCIA Porting
Hi!
The last 2 weeks I worked full time on PCMCIA. We have a custom board with a MPC860T 10/100MBit Ethernet one PCMCIA slot 8MB flash and 32MB RAM.
First at all: It works now fine. And I want to thank everyone who posted information to this issue (Magnus Damm, Matthew Locke, Wolfgang Denk and all others). But this the point for my mail:
It was/is very difficult to get all needed information, to get it to work, so I want to list my steps there, that it is maybe easier to do this work again.
O.K. here is a history of my work:
I linked the pcmcia stuff directly to the kernel (driver/pcmcia), because I think I understand it right Wolfgang, your PCMCIA onyl works if PPCBoot setup the PCMCIA port. But we don't use PPCBoot (shame about that .... ) and it seems to be to complicated/more work to add the whole stuff into our boot up sequence. I know that we loose the possibilty to mount root from a flash card, but we could live with that. Maybe Wolfgang has another hint for me ... :-)
However, I start of course where everyone startet:
http://lists.linuxppc.org/linuxppc-embedded/200002/msg00093.html and http://lists.linuxppc.org/linuxppc-embedded/200005/msg00227.html.
We portet also the mvista kernel 2.4.2 to the denx kernel 2.4.4
Then I add the _IO_BASE etc to the board specific h file and ioremap it as desribed (arch/ppc/kernem/mm/init.c)
-Fine-
Next step was to add the m8xx_pcmcia.c file to drivers/pcmcia and adapt the Config.in and Makefile. Then I do the board specific stuff for power supply in m8xx_pcmcia.c. Till now everything works fine.
But from this point on it becomes difficult, because from now on the interrupts comes up.
The first issue was in cs.c in drivers/pcmcia in the function pcmcia_request_irq
/* Short cut: if there are no ISA interrupts, then it is PCI */
#if 0
if (!s->cap.irq_mask) {
irq = s->cap.pci_irq;
ret = (irq) ? 0 : CS_IN_USE;
printk("Uhu: %08x %08x\n",s->cap.irq_mask,s->cap.pci_irq);
#endif
if (s->cap.irq_mask == (1 << s->cap.pci_irq)) {
irq = s->cap.pci_irq;
printk("Uhu: %08x %08x\n",s->cap.irq_mask,s->cap.pci_irq);
#ifdef CONFIG_ISA
} else if (s->irq.AssignedIRQ != 0) {
/* If the interrupt is already assigned, it must match */
irq = s->irq.AssignedIRQ;
if (req->IRQInfo1 & IRQ_INFO2_VALID) {
u_int mask = req->IRQInfo2 & s->cap.irq_mask;
ret = ((mask >> irq) & 1) ? 0 : CS_BAD_ARGS;
} else
ret = ((req->IRQInfo1&IRQ_MASK) == irq) ? 0 : CS_BAD_ARGS;
} else {
ret = CS_IN_USE;
if (req->IRQInfo1 & IRQ_INFO2_VALID) {
u_int try, mask = req->IRQInfo2 & s->cap.irq_mask;
for (try = 0; try < 2; try++) {
for (irq = 0; irq < 32; irq++)
if ((mask >> irq) & 1) {
ret = try_irq(req->Attributes, irq, try);
if (ret == 0) break;
}
if (ret == 0) break;
}
} else {
irq = req->IRQInfo1 & IRQ_MASK;
ret = try_irq(req->Attributes, irq, 1);
}
#else /* Right now m8xx specific */
} else if (s->irq.AssignedIRQ != 0) {
/* If the interrupt is already assigned, it must match */
irq = s->irq.AssignedIRQ;
if (req->IRQInfo1 & IRQ_INFO2_VALID) {
mask = req->IRQInfo2 & s->cap.irq_mask;
ret = ((mask >> irq) & 1) ? 0 : CS_BAD_ARGS;
} else
ret = ((req->IRQInfo1&IRQ_MASK) == irq) ? 0 : CS_BAD_ARGS;
} else {
ret = 0;
irq = 7; //SIU_LEVEL4
#endif
}The #if 0 and #if CONFIG_ISA tree is the original one, and the #else /*Right now m8xx specific */ part was taken from sourceforge pcmcia-cs 3.2.4.
The last point was the request_irq function. I don't change the defines in the h files, I change the function itself: arch/ppc/kernel/ppc8xx_pic.c. There (in request_irq) I call always the request_8xxirq function.
Quoted 1 line
From now on it works. I used for the first steps the file system from the eldk and copy then the necessary files (cardctl, cardmgr, scripts) to our filesystem.
I hope I didn't forget anything, please tell me if I've done a lot of nonsense, and I hope this will help in future if anyone has to do these steps anyway
best regards
Gerhard
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Hi,
Quoted 2 lines · in message <[email protected]> you wrote:
The last 2 weeks I worked full time on PCMCIA. We have a custom board with a MPC860T 10/100MBit Ethernet one PCMCIA slot 8MB flash and 32MB RAM.
Ummm... may I ask why you re-invented the wheel?
Quoted 1 line
I linked the pcmcia stuff directly to the kernel (driver/pcmcia), because I think I understand it right Wolfgang, your PCMCIA onyl works if PPCBoot setup the PCMCIA port. But we don't use PPCBoot (shame about that .... ) and it seems to be to complicate
If you use the direct IDE support as implemented in our kernel tree, Linux reads the memory map of the PCMCIA port from the pcmc_pbrX / pcmc_porX registers. That's all. Initializing these registers in Linux is trivial. The reason we avoid it is because this may be board-dependend.
Quoted 1 line
d/more work to add the whole stuff into our boot up sequence. I know that we loose the possibilty to mount root from a flash card, but we could live with that. Maybe Wolfgang has another hint for me ... :-)
We include both the direct IDE interface and the full PCMCIA card services package with our ELDK. It has been tested and is working fine on a couple of differenrt boards. We even support both PCMCIA slots on MPC860 systems.
Quoted 1 line
However, I start of course where everyone startet:
I'm sorry, but this is ancient stuff. Why didn't you use more recent code for your work?
Quoted 1 line
We portet also the mvista kernel 2.4.2 to the denx kernel 2.4.4
What exactly do you mean with this statement?
Quoted 1 line
Quoted 1 line
From now on it works. I used for the first steps the file system from the eldk and copy then the necessary files (cardctl, cardmgr, scripts) to our filesystem.
All of this (and more) is included and ready for use in the ELDK. It's a pity you wasted so much work without asking earlier :-(
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-4596-87 Fax: (+49)-8142-4596-88 Email: [email protected] Perfection is reached, not when there is no longer anything to add, but when there is no longer anything to take away.
- Antoine de Saint-Exupery
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/