various problems with usb2.0 pcmcia adaptor
Kernel Version: 2.6.0-test5-bk8
I've got some problems with the D-Link DUB-C2 2Port USB2.0 PCMCIA adaptor. If present at boot up time, the kernel hangs after initiating a second Yenta Socket (log below).
When inserted into a running system ohci-hcd generates multiple error messages.
Bootup - Log (hand copied):
| Yenta: CardBus Bridge fount at 0000:02:05.0 [103c:001a] | Yenta: Enabling burst memory read transactions | Yenta: Using INTVAL to route CSC interrupts to PCI | Yenta: Routing CardBus interrupts to PCI | Yenta: ISA IRQ list 0a98, PCI irq 10 | Socket status: 300000006 [..] | Yenta: CardBus Bridge fount at 0000:02:05.1 [103c:001a] | Yenta: Enabling burst memory read transactions | Yenta: Using INTVAL to route CSC interrupts to PCI | Yenta: Routing CardBus interrupts to PCI | Yenta: ISA IRQ list 0a98, PCI irq 10 | Socket status: 300000020
[computer hangs]
Tried to disable the onboard usb controller, but the system BIOS won't allow it (POS in question is a HP Omnibook 6100).
The error messages which could be gained by inserting the PCMCIA card after booting are:
| cs: IO port probe 0x0c00-0x0cff: clean. | cs: IO port probe 0x0800-0x08ff: clean. | cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x3c0-0x3df 0x4d0-0x4d7 | cs: IO port probe 0x0a00-0x0aff: clean. | ohci-hcd: 2003 Feb 24 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) | ohci-hcd: block sizes: ed 64 td 64 | PCI: Enabling device 0000:07:00.0 (0000 -> 0002) | ohci-hcd 0000:07:00.0: OHCI Host Controller | PCI: Setting latency timer of device 0000:07:00.0 to 64 | ohci-hcd 0000:07:00.0: irq 10, pci mem d2c7d000 | ohci-hcd 0000:07:00.0: new USB bus registered, assigned bus number 2 | ohci-hcd 0000:07:00.0: HC died; cleaning up | usb usb2: device not accepting address 1, error -22 | ohci-hcd 0000:07:00.0: can't register root hub for usb2, -22 | ohci-hcd 0000:07:00.0: can't start | ohci-hcd 0000:07:00.0: remove, state 0 | ohci-hcd 0000:07:00.0: USB bus 2 deregistered | ohci-hcd: probe of 0000:07:00.0 failed with error -16 | ohci-hcd 0000:07:00.1: OHCI Host Controller
and:
| ohci-hcd: 2003 Feb 24 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) | ohci-hcd: block sizes: ed 64 td 64 | PCI: Enabling device 0000:07:00.0 (0000 -> 0002) | ohci-hcd 0000:07:00.0: OHCI Host Controller | PCI: Setting latency timer of device 0000:07:00.0 to 64 | ohci-hcd 0000:07:00.0: irq 10, pci mem d18ae000 | ohci-hcd 0000:07:00.0: new USB bus registered, assigned bus number 2 | hub 2-0:0: USB hub found | hub 2-0:0: 3 ports detected | PCI: Enabling device 0000:07:00.1 (0000 -> 0002) | ohci-hcd 0000:07:00.1: OHCI Host Controller | PCI: Setting latency timer of device 0000:07:00.1 to 64 | ohci-hcd 0000:07:00.1: irq 10, pci mem d18b8000 | ohci-hcd 0000:07:00.1: new USB bus registered, assigned bus number 3 | hub 3-0:0: USB hub found | hub 3-0:0: config failed, hub has too many ports! (err -19)
[true, it has only 2 ports.]
| ehci_hcd 0000:07:00.2: EHCI Host Controller
--Andreas
Quoted 1 line · Andreas Happe
Kernel Version: 2.6.0-test5-bk8
I tried to send you a response, but your mail system seems broken:
[email protected]
SMTP error from remote mailer after RCPT TO:<[email protected]>:
host mx0.gmx.net [213.165.64.100]: 552 {mx008} The users mailbox is full
Please ensure that your mailbox isn't full before asking questions which will solicit more mail into your mailbox.
Signature · 4 lines
Russell King ([email protected]) http://www.arm.linux.org.uk/personal/ Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/ maintainer of: 2.6 PCMCIA - http://pcmcia.arm.linux.org.uk/ 2.6 Serial core
Quoted 2 lines · Russell King
Please ensure that your mailbox isn't full before asking questions which will solicit more mail into your mailbox.
I must apologize, i was hit by swen, the mailbox should be free by now.
--Andreas