VHUB didn't work on AST2500
Hi Ben, Andrew,
I found the reason is that the key values are different between usb-vhub keyboard and physical keyboard. The vhub key value has one more byte than physical. and it seemed that vhub mouse uses keyboard channel, the BIOS can receive values from vhub mouse even if BIOS closed the mouse driver.
1, When the vhub mouse moves from ikvm, the vhub mouse sends out 6 bytes data to keyboard channel:
02 00 50 14 CE 22
02 00 B0 0E E8 20
02 00 48 08 96 1E
..........
2, The first byte of data sent by the vhub keyboard value is incorrect. The first byte is 01, which means that the control key is pressed from the physical keyboard view.
1) using vhub keyboard
Presses the key 'a' , BIOS receives data:
01 00 00 04 00 00 00 00
Release key 'a' ,BIOS receives data:
01 00 00 00 00 00 00 00
Press 'Control' +'a' ,BIOS receives data:
01 01 00 04 00 00 00 00
Press the key'1' ,BIOS receives data:
01 00 1E 00 00 00 00
Release key'1'usb, BIOS receives data:
01 00 00 00 00 00 00
2) using physical keyboard
Press the key 'a' ,BIOS receives data:
00 00 04 00 00 00 00 00
Release key 'a' usb ,BIOS receives data::
00 00 00 00 00 00 00 00
Press 'Control' + 'a' ,BIOS receives data:
01 00 04 00 00 00 00 00
Press the key '1' ,BIOS receives data:
00 00 1E 00 00 00 00 00
Release key '1' ,BIOS receives data:
00 00 00 00 00 00 00 00
Why does the vhub keyboard has the extra first byte '01'? Why vhub mouse use keyboard channel to transfer data?
Best,
xiuzhi
------------------ Original ------------------
From: "Benjamin Herrenschmidte";<[email protected]>;
Send time: Monday, Nov 5, 2018 7:09 AM
To: "xiuzhi"<[email protected]>; "Andrew.Jeffery"<[email protected]>; "EddieJames"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500
Quoted 10 lines · xiuzhi
Hi Ben,
Did you reproduce this issue?
I found this issue is related to the host UEFI BIOS usb driver last week.
My host BIOS is cloned from udk2017 (www.uefi.org) .
The ikvm mouse and keyboard work when the BIOS runs on legacy mode
and will fail on UEFI mode.
I also compared the AMI BMC and OpenBMC.
The AMI BMC ikvm (version is r11) works on this problematic BIOS ,while OpenBMC will fail on the same one . The OpenBMC ikvm works on legacy mode ,and fails on UEFI mode.
Do you have any suggestions ?
That's good to know any explains why I cannot reproduce as I don't have an UEFI system to test with.
I suspect something the UEFI BIOS does that upsets the Linux USB gadget stack.
I could debug this if I had access to a system, either physically here or remotely, where I can remotely install/netboot BMC kernels (so I would probably need a serial connection to the BMC and a PDU), any suggestion on how to do that ?
Otherwise, would there be a way to reproduce that with the x86 running in qemu ? (plugging the AST2500 eval board USB into the host and passing it through for example) ?
Cheers,
Ben.
Quoted 746 lines
Best,
Xiuzhi
Hi Eddie,
The new obmc-ikvm has an new issue which got from https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/13888/
The number key 0-9 can input at the first BMC boot start-ipkvm.service.
It can't input any key when I restart the host ,and restart the start-ipkvm.service because of host screen resolution changed :
systemctl restart start-ipkvm.service
dmesg log:[ 144.990545] aspeed-video 1e700000.video: resolution changed; resetting [ 145.135654] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 145.135672] configfs-gadget gadget: suspend [ 146.020671] aspeed-video 1e700000.video: timed out on 1st mode detect [ 146.027154] aspeed-video 1e700000.video: resolution changed; couldn't get new resolution [ 267.098598] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 267.098623] configfs-gadget gadget: resume [ 267.098642] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 267.098650] configfs-gadget gadget: suspend [ 267.241258] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 267.241292] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 267.241308] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 267.262265] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 267.262293] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.266784] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 267.266805] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.271552] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 267.271585] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.275390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 267.275422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.284132] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 267.284475] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 267.284850] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 267.318337] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 267.318370] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.318723] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 267.318749] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318765] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.322862] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 267.322892] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 267.323093] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 267.323121] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 267.323343] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 267.323368] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 267.323595] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 267.323622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 267.323843] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 267.323870] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 267.344036] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.344069] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 267.481060] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.481091] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.481108] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 267.481446] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 267.481468] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 267.596168] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 267.596202] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 267.596217] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 267.596237] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -> 0011 (C=0) [ 267.596251] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at known speed of bound device, resetting... [ 267.596259] configfs-gadget gadget: reset config [ 267.596275] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Disabling ! [ 267.596288] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Nuking [ 267.596307] configfs-gadget gadget: End Point Request ERROR: -108 [ 267.602439] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Disabling ! [ 267.602458] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Nuking [ 267.602496] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -> 0403 (C=1) [ 267.622677] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.622710] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.622729] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 267.623097] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 267.623127] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 267.623344] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 267.623373] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 267.636359] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=2 [ 267.636389] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 wrong state [ 267.636402] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636412] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636423] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 267.653534] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.653566] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.653582] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.673140] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.673159] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673596] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.673622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi
Hi Andrew,
Sorry , the pinctrl error was not caused by uart-render-controller .
The reason is I definded a wrong gpio pin GPIOI3 (It is pin67) in filerecipes-phosphor/sekleton/obmc-libobmc-intfgpio_defs.json.The error message dispeared after I removed the pin definition. Now, the error of character key inputting still exists as well .
Best,
xiuzhi
Hi Andrew,Quoted 10 lines
Quoted 8 lines
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?
it was caused by uart-render-controller.service:
"
ExecStart=/usr/sbin/obmc-uart-render-controller \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \
fbterm.service
"
fbterm is related to keyinput.
AST2500 only support up to 228 gpio pins,but the error message read gpio:347 ,I don't know why ?Best,
Xiuzhi
------------------ Original ------------------
From: "Andrew.Jeffery";<[email protected]>;
Send time: Sunday, Oct 28, 2018 3:02 PM
To: "xiuzhi"<[email protected]>; "Benjamin Herrenschmidt"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 51 lines · xiuzhi
Hi Ben, Eddie,
I update the kernel,libvncserver,obmc-ikvm source to the latest git
commit numbers.
Now I can input number key 0-9, but still can't input any character key a-z .
1)kernel:
KSRC ?= "git://github.com/eddiejames/linux;protocol=git;branch=${KBRANCH}"
KBRANCH ?= "video-dev"LINUX_VERSION?= "4.18.12"
SRCREV = "b953727d56c4de63eb0fad1f079f41004e61d713"
and updated the defconfig,create_usbhid.sh as Eddie mentioned . 2)libvncserverSRC_URI= "git://github.com/LibVNC/libvncserver"SRCREV = "
ca2a5ac02fbbadd0a21fabba779c1ea69173d10b" 3)obmc-ikvmSRC_URI= "git://github.com/eddiejames/obmc-ikvm" SRCREV = "d548ee6c8f59c23552d61fb28b2ca2f20e6f3fe6"
4) I input key on host BIOS CLI:
"1234567890" 'Enter' : good ,can see them on host screen 'a' 'Enter':error ,see nothing
'b' 'Enter':error,see nothing
'c' 'Enter':error,see nothing "123456789"'Enter':good
The dmesg is :[ 57.002351] udc 1e6a0000.usb-vhub:p1: registering UDC driver [obmc_hid] [ 57.002452] configfs-gadget gadget: adding 'hid'/e5acc706 to config 'c'/7ef6bc13 [ 57.002488] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.002509] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 0 for addr 1 [ 57.013399] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0 for port EP1 [ 57.013435] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.013453] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 1 for addr 2 [ 57.018946] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1 for port EP2 [ 57.019463] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 57.019492] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 57.019512] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0000 -Quoted 1 line
0001 (C=1)
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67Quoted 3 lines
(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?
/sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \ fbterm.serviceQuoted 561 lines
[ 100.115387] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.115411] configfs-gadget gadget: resume [ 100.115427] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.258057] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 100.258092] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 100.258107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 100.279075] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.279103] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.283632] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.283664] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.288371] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.288405] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.292205] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 100.292235] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.300948] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.301268] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.301640] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.335144] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 100.335178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335196] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.335527] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 100.335554] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335569] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.339672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 100.339703] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 100.339890] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 100.339912] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 100.340139] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 100.340160] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 100.340386] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 100.340404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 100.340637] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 100.340656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 100.360852] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.360884] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.500028] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.500062] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.500082] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 100.500404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 100.500435] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 100.615543] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 100.615579] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 100.615594] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.615612] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -Quoted 1 line
0011 (C=0)
[ 100.615626] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknown speed of disabled device, enabling... [ 100.615643] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -Quoted 1 line
0403 (C=1)
[ 100.635854] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.635885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.635903] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 100.636271] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 100.636299] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 100.636515] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 100.636540] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 100.649529] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=0 [ 100.649564] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet, captured speed 3 [ 100.649580] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Got address 3 [ 100.665314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.665345] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.665363] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.680170] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.680200] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.680234] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.684627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.684657] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.684690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.689471] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.689500] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.689538] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.693198] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0029 [in] st=0 [ 100.693231] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.693267] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.701949] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.701983] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702020] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.702432] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702466] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702774] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.702799] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702818] configfs-gadget gadget: high-speed config #1: c [ 100.708470] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling [in] intr num 1 maxpacket=11 [ 100.708512] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling [out] intr num 2 maxpacket=11 [ 100.708565] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.777585] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/08/0000/0000/0001 [in] st=0 [ 100.777619] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.777649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778029] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet a1/03/0000/0000/0001 [in] st=0 [ 100.778055] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778085] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/0b/0000/0000/0000 [out] st=0 [ 100.778428] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778457] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.778672] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778692] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.778704] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.778746] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.859563] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.859592] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.859618] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.859633] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.892835] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.892866] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.892882] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.893278] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.893305] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Saturday, Oct 27, 2018 7:55 AM
To: "xiuzhi"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 4 lines · xiuzhi
Hi Eddie,
Thanks for your reply.
It seemd that the error was caused by the version dismatch of kernel ,libvncserver ,obmc-ikvm and vnc client. Would you like to give me your git commits numbers of them?It's still a very strange error.
Once everything is up to date, let me know if it occurs again, there's something not right going on in the vhub driver causing that state mismatch error, it shouldn't happen. But I haven't managed to reproduce it here.
Cheers,
Ben.Quoted 332 lines
Best,
xiuzhiQuoted 16 lines · xiuzhi
Hi Ben,
I use vncviewer , xtightvncviewer 1.3.9-6.4ubuntu1.
And I also tested the ikvm by webui vnc(_https://gerrit.openbmc-project.xyz/#/c/openbmc/phosphor-webui/+/10268/_) ,the same errors occured.
The same source code obmc-ikvm and this kernel branch video-dev5 works on my other AST2400 hardware machine.
I remembered only one kernel version seemed to work on ast2500 ,I tested it six weeks ago .
the kernel version is:KBRANCH ?= "video-dev"
LINUX_VERSION?= "4.17.11" SRCREV="09a65900b2fc7aab9caf9d0dfabc7ba80525b1dd" the git repo is fromgit://github.com/eddiejames/linux/,Quoted 5 lines
https://gerrit.openbmc-project.xyz/#/c/openbmc/openbmc/+/11500/5/meta-openbmc-bsp/meta-aspeed/recipes-kernel/linux/linux-aspeed_git.bb
I want to test this kernel version ,but now this git repo is not available ,
I asked Eddiejames week ago, and get no response until now . It is so bad that I did not backup this kernel on my local machice.I never made any kernel changes related to USB in my github trees, as far as I know, so shouldn't be any difference. That original gerrit commit was purely for our testing purposes for our system... not really something I can support actively.
I have a number of commits pending review that you could try and pull in if you really need this now:
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-phosphor/+/13536/
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-aspeed/+/13541/
https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/12126/Use these in combination with the two commits at the top of my video-dev linux tree for your kernel.
Thanks,
EddieQuoted 289 lines
Best.
XiuzhiQuoted 4 lines · xiuzhi
Hi Ben,
I open theCONFIG_USB_GADGET_DEBUG.
and input the following keys by order:
';''Enter' :work good,can see ';' on host screenQuoted 8 lines
'a''Enter' :error,see anything on screen
'b''Enter' :error,see anything on screen
'1''Enter' :good
'2''Enter' :good
'3''Enter' :good
'4''Enter' :good
'5''Enter' :error deadlock
The log is:Can you tell me more about the userspace components you use to send those keys ? I'd like to try to reproduce here.
Quoted 1 line
[ 78.820671] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 78.828274] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Quoted 1 line
[ 80.698564] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 80.706166] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -
Quoted 1 line
[ 94.447816] udc 1e6a0000.usb-vhub:p1: registering UDC driver[
obmc_hid]Quoted 1 line
[ 94.447909] configfs-gadget gadget: adding 'hid'/15e5a204 toconfig 'c'/70dd0747
Quoted 2 lines
[ 94.447940] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.447958] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 0 for addr 1
Quoted 1 line
[ 94.448474] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0for port EP1
Quoted 2 lines
[ 94.448505] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.448522] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 1 for addr 2
Quoted 1 line
[ 94.448780] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1for port EP2
Quoted 3 lines
[ 94.449270] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 94.449297] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 94.449317] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0000 -> 0001 (C=1)
Quoted 4 lines
[ 100.158377] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.158400] configfs-gadget gadget: resume [ 100.158415] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.301048] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/05/0002/0000/0000 [out] st=0
Quoted 1 line
[ 100.301081] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000speed=high
Quoted 1 line
[ 100.301096] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS:Got address 2
Quoted 1 line
[ 100.322061] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.322090] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.326625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.326656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.331359] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.331392] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.335194] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0019 [in] st=0
Quoted 1 line
[ 100.335221] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.343939] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.344272] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.344647] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.378145] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0002 [in] st=0
Quoted 1 line
[ 100.378178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378195] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.378522] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0009 [in] st=0
Quoted 1 line
[ 100.378546] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378560] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.382665] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0001/0000 [out] st=0
Quoted 1 line
[ 100.382697] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,8)Quoted 1 line
[ 100.382896] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0002/0000 [out] st=0
Quoted 1 line
[ 100.382922] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(2,8)Quoted 1 line
[ 100.383148] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0003/0000 [out] st=0
Quoted 1 line
[ 100.383173] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(3,8)Quoted 1 line
[ 100.383396] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0004/0000 [out] st=0
Quoted 1 line
[ 100.383422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(4,8)Quoted 1 line
[ 100.383643] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0005/0000 [out] st=0
Quoted 1 line
[ 100.383668] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(5,8)Quoted 1 line
[ 100.403844] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 2 lines
[ 100.403871] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.549225] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.549257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.549275] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0101 change=0001
Quoted 1 line
[ 100.549651] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0010/0001/0000 [out] st=0
Quoted 1 line
[ 100.549681] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,16)Quoted 1 line
[ 100.664592] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0004/0001/0000 [out] st=0
Quoted 1 line
[ 100.664625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,4)Quoted 2 lines
[ 100.664639] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.664658] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0001 -> 0011 (C=0)
Quoted 1 line
[ 100.664672] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknownspeed of disabled device, enabling.
Quoted 1 line
[ 100.664689] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0011 -> 0403 (C=1)
Quoted 1 line
[ 100.684840] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.684867] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.684885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0012
Quoted 1 line
[ 100.685276] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0011/0001/0000 [out] st=0
Quoted 1 line
[ 100.685306] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,17)Quoted 1 line
[ 100.685518] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0014/0001/0000 [out] st=0
Quoted 1 line
[ 100.685544] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,20)Quoted 1 line
[ 100.698539] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/05/0003/0000/0000 [out] st=0
Quoted 1 line
[ 100.698568] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet,captured speed 3
Quoted 1 line
[ 100.698585] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Gotaddress 3
Quoted 1 line
[ 100.714314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.714339] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.714354] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.729165] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.729195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.729227] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.733627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.733658] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.733690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.738363] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.738391] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.738427] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.742195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0029 [in] st=0
Quoted 1 line
[ 100.742225] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.742262] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.750944] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.750972] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751400] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.751425] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751455] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751777] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.751803] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 2 lines
[ 100.751821] configfs-gadget gadget: high-speed config #1: c [ 100.757460] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling[in] intr num 1 maxpacket=11
Quoted 1 line
[ 100.757502] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling[out] intr num 2 maxpacket=11
Quoted 1 line
[ 100.757549] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.820566] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/08/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.820594] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.820621] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821026] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packeta1/03/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.821050] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821076] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821397] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/0b/0000/0000/0000 [out] st=0
Quoted 1 line
[ 100.821422] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821451] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821643] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.821666] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821685] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 3 lines
[ 100.821697] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.821735] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.913006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.913034] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.913056] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 2 lines
[ 100.913067] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.946228] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.946257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.946274] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.946645] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 11 lines
[ 100.946672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 399.741059] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 399.741081] configfs-gadget gadget: suspendBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Thursday, Oct 25, 2018 6:42 AM
To: "Joel Stanley"<[email protected]>; "xiuzhi"<[email protected]>;
Cc: "a.filippov"<[email protected]>; "OpenBMCMaillist"<[email protected]>;
Quoted 5 lines
Subject: Re: VHUB didn't work on AST2500
Quoted 2 lines · Joel Stanley
Quoted 1 line · xiuzhi
I am porting obmc-ikvm to my hardware platform. The host screen
can be seen by vncviewer , but the mouse and keyboard didn't work on AST2500
Quoted 1 line
Quoted 1 line
Quoted 1 line
. Only the keys ';' , 'Enter', '1','2','3','4' work. others
keyinput will deadlock the host screen .
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
The kernel error log:
[ 99.326586] configfs-gadget gadget: high-speed config #1: c [ 99.403704] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 1 line
Quoted 1 line
Quoted 1 line
[ 99.492831] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 19 lines
Quoted 6 lines
Quoted 4 lines
The kernel version is : video-dev5,
commit2acbc35adcfe15971b701770e1105276a18da9f7Who can give me some suggestions to debug it?
Ben, do you have any advice?
I need to know a bit more. What is used as a gadget driver on the BMC ?
I would probably need to reproduce with some added traces to the driver to figure out what's going on.
One first thing to try would be a run with
CONFIG_USB_GADGET_DEBUGalong with some indication of what actions happen corresponding to what part of the log (ie, press key 'a' etc...).Cheers,
Ben.
Quoted 3 lines · xiuzhi
Hi Ben, Andrew,
I found the reason is that the key values are different between usb-vhub keyboard and physical keyboard. The vhub key value has one more byte than physical. and it seemed that vhub mouse uses keyboard channel, the BIOS can receive values from vhub mouse even if BIOS closed the mouse driver.
1, When the vhub mouse moves from ikvm, the vhub mouse sends out 6 bytes data to keyboard channel:
vhub itself just passes the data that's coming from the HID gadget driver, I don't know much about how it construct packets or is configured, you may want to look into it.
Ben.
Quoted 830 lines
02 00 50 14 CE 22
02 00 B0 0E E8 20
02 00 48 08 96 1E
..........
2, The first byte of data sent by the vhub keyboard value is incorrect. The first byte is 01, which means that the control key is pressed from the physical keyboard view.
1) using vhub keyboard
Presses the key 'a' , BIOS receives data:01 00 00 04 00 00 00 00
Release key 'a' ,BIOS receives data:
01 00 00 00 00 00 00 00
Press 'Control' +'a' ,BIOS receives data:
01 01 00 04 00 00 00 00
Press the key'1' ,BIOS receives data:01 00 1E 00 00 00 00
Release key'1'usb, BIOS receives data:
01 00 00 00 00 00 00
2) using physical keyboard
Press the key 'a' ,BIOS receives data:
00 00 04 00 00 00 00 00Release key 'a' usb ,BIOS receives data::
00 00 00 00 00 00 00 00
Press 'Control' + 'a' ,BIOS receives data:
01 00 04 00 00 00 00 00
Press the key '1' ,BIOS receives data:00 00 1E 00 00 00 00 00
Release key '1' ,BIOS receives data:
00 00 00 00 00 00 00 00
Why does the vhub keyboard has the extra first byte '01'? Why vhub mouse use keyboard channel to transfer data?Best,
xiuzhi
------------------ Original ------------------
From: "Benjamin Herrenschmidte";<[email protected]>;
Send time: Monday, Nov 5, 2018 7:09 AM
To: "xiuzhi"<[email protected]>; "Andrew.Jeffery"<[email protected]>; "EddieJames"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 10 lines · xiuzhi
Hi Ben,
Did you reproduce this issue?
I found this issue is related to the host UEFI BIOS usb driver last week.
My host BIOS is cloned from udk2017 (www.uefi.org) .
The ikvm mouse and keyboard work when the BIOS runs on legacy mode
and will fail on UEFI mode.
I also compared the AMI BMC and OpenBMC.
The AMI BMC ikvm (version is r11) works on this problematic BIOS ,while OpenBMC will fail on the same one . The OpenBMC ikvm works on legacy mode ,and fails on UEFI mode.
Do you have any suggestions ?That's good to know any explains why I cannot reproduce as I don't have an UEFI system to test with.
I suspect something the UEFI BIOS does that upsets the Linux USB gadget stack.
I could debug this if I had access to a system, either physically here or remotely, where I can remotely install/netboot BMC kernels (so I would probably need a serial connection to the BMC and a PDU), any suggestion on how to do that ?
Otherwise, would there be a way to reproduce that with the x86 running in qemu ? (plugging the AST2500 eval board USB into the host and passing it through for example) ?
Cheers,
Ben.Quoted 746 lines
Best,
Xiuzhi
Hi Eddie,
The new obmc-ikvm has an new issue which got from https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/13888/
The number key 0-9 can input at the first BMC boot start-ipkvm.service.
It can't input any key when I restart the host ,and restart the start-ipkvm.service because of host screen resolution changed :
systemctl restart start-ipkvm.service
dmesg log:[ 144.990545] aspeed-video 1e700000.video: resolution changed; resetting [ 145.135654] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 145.135672] configfs-gadget gadget: suspend [ 146.020671] aspeed-video 1e700000.video: timed out on 1st mode detect [ 146.027154] aspeed-video 1e700000.video: resolution changed; couldn't get new resolution [ 267.098598] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 267.098623] configfs-gadget gadget: resume [ 267.098642] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 267.098650] configfs-gadget gadget: suspend [ 267.241258] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 267.241292] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 267.241308] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 267.262265] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 267.262293] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.266784] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 267.266805] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.271552] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 267.271585] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.275390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 267.275422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.284132] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 267.284475] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 267.284850] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 267.318337] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 267.318370] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.318723] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 267.318749] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318765] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.322862] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 267.322892] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 267.323093] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 267.323121] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 267.323343] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 267.323368] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 267.323595] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 267.323622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 267.323843] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 267.323870] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 267.344036] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.344069] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 267.481060] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.481091] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.481108] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 267.481446] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 267.481468] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 267.596168] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 267.596202] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 267.596217] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 267.596237] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -> 0011 (C=0) [ 267.596251] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at known speed of bound device, resetting... [ 267.596259] configfs-gadget gadget: reset config [ 267.596275] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Disabling ! [ 267.596288] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Nuking [ 267.596307] configfs-gadget gadget: End Point Request ERROR: -108 [ 267.602439] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Disabling ! [ 267.602458] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Nuking [ 267.602496] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -> 0403 (C=1) [ 267.622677] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.622710] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.622729] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 267.623097] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 267.623127] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 267.623344] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 267.623373] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 267.636359] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=2 [ 267.636389] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 wrong state [ 267.636402] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636412] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636423] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 267.653534] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.653566] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.653582] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.673140] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.673159] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673596] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.673622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi
Hi Andrew,
Sorry , the pinctrl error was not caused by uart-render-controller .
The reason is I definded a wrong gpio pin GPIOI3 (It is pin67) in filerecipes-phosphor/sekleton/obmc-libobmc-intfgpio_defs.json.The error message dispeared after I removed the pin definition. Now, the error of character key inputting still exists as well .
Best,
xiuzhi
Hi Andrew,Quoted 10 lines
Quoted 8 lines
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?
it was caused by uart-render-controller.service:
"
ExecStart=/usr/sbin/obmc-uart-render-controller \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \
fbterm.service
"
fbterm is related to keyinput.
AST2500 only support up to 228 gpio pins,but the error message read gpio:347 ,I don't know why ?Best,
Xiuzhi
------------------ Original ------------------
From: "Andrew.Jeffery";<[email protected]>;
Send time: Sunday, Oct 28, 2018 3:02 PM
To: "xiuzhi"<[email protected]>; "Benjamin Herrenschmidt"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 51 lines · xiuzhi
Hi Ben, Eddie,
I update the kernel,libvncserver,obmc-ikvm source to the latest git
commit numbers.
Now I can input number key 0-9, but still can't input any character key a-z .
1)kernel:
KSRC ?= "git://github.com/eddiejames/linux;protocol=git;branch=${KBRANCH}"
KBRANCH ?= "video-dev"LINUX_VERSION?= "4.18.12"
SRCREV = "b953727d56c4de63eb0fad1f079f41004e61d713"
and updated the defconfig,create_usbhid.sh as Eddie mentioned . 2)libvncserverSRC_URI= "git://github.com/LibVNC/libvncserver"SRCREV = "
ca2a5ac02fbbadd0a21fabba779c1ea69173d10b" 3)obmc-ikvmSRC_URI= "git://github.com/eddiejames/obmc-ikvm" SRCREV = "d548ee6c8f59c23552d61fb28b2ca2f20e6f3fe6"
4) I input key on host BIOS CLI:
"1234567890" 'Enter' : good ,can see them on host screen 'a' 'Enter':error ,see nothing
'b' 'Enter':error,see nothing
'c' 'Enter':error,see nothing "123456789"'Enter':good
The dmesg is :[ 57.002351] udc 1e6a0000.usb-vhub:p1: registering UDC driver [obmc_hid] [ 57.002452] configfs-gadget gadget: adding 'hid'/e5acc706 to config 'c'/7ef6bc13 [ 57.002488] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.002509] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 0 for addr 1 [ 57.013399] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0 for port EP1 [ 57.013435] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.013453] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 1 for addr 2 [ 57.018946] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1 for port EP2 [ 57.019463] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 57.019492] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 57.019512] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0000 -Quoted 1 line
0001 (C=1)
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67Quoted 3 lines
(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?
/sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \ fbterm.serviceQuoted 561 lines
[ 100.115387] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.115411] configfs-gadget gadget: resume [ 100.115427] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.258057] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 100.258092] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 100.258107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 100.279075] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.279103] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.283632] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.283664] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.288371] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.288405] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.292205] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 100.292235] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.300948] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.301268] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.301640] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.335144] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 100.335178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335196] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.335527] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 100.335554] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335569] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.339672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 100.339703] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 100.339890] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 100.339912] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 100.340139] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 100.340160] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 100.340386] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 100.340404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 100.340637] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 100.340656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 100.360852] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.360884] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.500028] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.500062] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.500082] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 100.500404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 100.500435] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 100.615543] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 100.615579] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 100.615594] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.615612] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -Quoted 1 line
0011 (C=0)
[ 100.615626] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknown speed of disabled device, enabling... [ 100.615643] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -Quoted 1 line
0403 (C=1)
[ 100.635854] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.635885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.635903] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 100.636271] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 100.636299] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 100.636515] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 100.636540] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 100.649529] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=0 [ 100.649564] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet, captured speed 3 [ 100.649580] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Got address 3 [ 100.665314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.665345] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.665363] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.680170] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.680200] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.680234] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.684627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.684657] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.684690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.689471] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.689500] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.689538] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.693198] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0029 [in] st=0 [ 100.693231] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.693267] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.701949] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.701983] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702020] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.702432] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702466] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702774] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.702799] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702818] configfs-gadget gadget: high-speed config #1: c [ 100.708470] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling [in] intr num 1 maxpacket=11 [ 100.708512] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling [out] intr num 2 maxpacket=11 [ 100.708565] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.777585] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/08/0000/0000/0001 [in] st=0 [ 100.777619] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.777649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778029] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet a1/03/0000/0000/0001 [in] st=0 [ 100.778055] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778085] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/0b/0000/0000/0000 [out] st=0 [ 100.778428] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778457] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.778672] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778692] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.778704] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.778746] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.859563] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.859592] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.859618] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.859633] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.892835] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.892866] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.892882] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.893278] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.893305] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Saturday, Oct 27, 2018 7:55 AM
To: "xiuzhi"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 4 lines · xiuzhi
Hi Eddie,
Thanks for your reply.
It seemd that the error was caused by the version dismatch of kernel ,libvncserver ,obmc-ikvm and vnc client. Would you like to give me your git commits numbers of them?It's still a very strange error.
Once everything is up to date, let me know if it occurs again, there's something not right going on in the vhub driver causing that state mismatch error, it shouldn't happen. But I haven't managed to reproduce it here.
Cheers,
Ben.Quoted 332 lines
Best,
xiuzhiQuoted 16 lines · xiuzhi
Hi Ben,
I use vncviewer , xtightvncviewer 1.3.9-6.4ubuntu1.
And I also tested the ikvm by webui vnc(_https://gerrit.openbmc-project.xyz/#/c/openbmc/phosphor-webui/+/10268/_) ,the same errors occured.
The same source code obmc-ikvm and this kernel branch video-dev5 works on my other AST2400 hardware machine.
I remembered only one kernel version seemed to work on ast2500 ,I tested it six weeks ago .
the kernel version is:KBRANCH ?= "video-dev"
LINUX_VERSION?= "4.17.11" SRCREV="09a65900b2fc7aab9caf9d0dfabc7ba80525b1dd" the git repo is fromgit://github.com/eddiejames/linux/,Quoted 5 lines
https://gerrit.openbmc-project.xyz/#/c/openbmc/openbmc/+/11500/5/meta-openbmc-bsp/meta-aspeed/recipes-kernel/linux/linux-aspeed_git.bb
I want to test this kernel version ,but now this git repo is not available ,
I asked Eddiejames week ago, and get no response until now . It is so bad that I did not backup this kernel on my local machice.I never made any kernel changes related to USB in my github trees, as far as I know, so shouldn't be any difference. That original gerrit commit was purely for our testing purposes for our system... not really something I can support actively.
I have a number of commits pending review that you could try and pull in if you really need this now:
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-phosphor/+/13536/
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-aspeed/+/13541/
https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/12126/Use these in combination with the two commits at the top of my video-dev linux tree for your kernel.
Thanks,
EddieQuoted 289 lines
Best.
XiuzhiQuoted 4 lines · xiuzhi
Hi Ben,
I open theCONFIG_USB_GADGET_DEBUG.
and input the following keys by order:
';''Enter' :work good,can see ';' on host screenQuoted 8 lines
'a''Enter' :error,see anything on screen
'b''Enter' :error,see anything on screen
'1''Enter' :good
'2''Enter' :good
'3''Enter' :good
'4''Enter' :good
'5''Enter' :error deadlock
The log is:Can you tell me more about the userspace components you use to send those keys ? I'd like to try to reproduce here.
Quoted 1 line
[ 78.820671] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 78.828274] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Quoted 1 line
[ 80.698564] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 80.706166] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -
Quoted 1 line
[ 94.447816] udc 1e6a0000.usb-vhub:p1: registering UDC driver[
obmc_hid]Quoted 1 line
[ 94.447909] configfs-gadget gadget: adding 'hid'/15e5a204 toconfig 'c'/70dd0747
Quoted 2 lines
[ 94.447940] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.447958] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 0 for addr 1
Quoted 1 line
[ 94.448474] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0for port EP1
Quoted 2 lines
[ 94.448505] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.448522] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 1 for addr 2
Quoted 1 line
[ 94.448780] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1for port EP2
Quoted 3 lines
[ 94.449270] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 94.449297] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 94.449317] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0000 -> 0001 (C=1)
Quoted 4 lines
[ 100.158377] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.158400] configfs-gadget gadget: resume [ 100.158415] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.301048] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/05/0002/0000/0000 [out] st=0
Quoted 1 line
[ 100.301081] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000speed=high
Quoted 1 line
[ 100.301096] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS:Got address 2
Quoted 1 line
[ 100.322061] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.322090] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.326625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.326656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.331359] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.331392] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.335194] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0019 [in] st=0
Quoted 1 line
[ 100.335221] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.343939] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.344272] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.344647] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.378145] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0002 [in] st=0
Quoted 1 line
[ 100.378178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378195] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.378522] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0009 [in] st=0
Quoted 1 line
[ 100.378546] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378560] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.382665] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0001/0000 [out] st=0
Quoted 1 line
[ 100.382697] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,8)Quoted 1 line
[ 100.382896] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0002/0000 [out] st=0
Quoted 1 line
[ 100.382922] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(2,8)Quoted 1 line
[ 100.383148] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0003/0000 [out] st=0
Quoted 1 line
[ 100.383173] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(3,8)Quoted 1 line
[ 100.383396] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0004/0000 [out] st=0
Quoted 1 line
[ 100.383422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(4,8)Quoted 1 line
[ 100.383643] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0005/0000 [out] st=0
Quoted 1 line
[ 100.383668] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(5,8)Quoted 1 line
[ 100.403844] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 2 lines
[ 100.403871] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.549225] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.549257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.549275] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0101 change=0001
Quoted 1 line
[ 100.549651] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0010/0001/0000 [out] st=0
Quoted 1 line
[ 100.549681] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,16)Quoted 1 line
[ 100.664592] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0004/0001/0000 [out] st=0
Quoted 1 line
[ 100.664625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,4)Quoted 2 lines
[ 100.664639] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.664658] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0001 -> 0011 (C=0)
Quoted 1 line
[ 100.664672] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknownspeed of disabled device, enabling.
Quoted 1 line
[ 100.664689] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0011 -> 0403 (C=1)
Quoted 1 line
[ 100.684840] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.684867] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.684885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0012
Quoted 1 line
[ 100.685276] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0011/0001/0000 [out] st=0
Quoted 1 line
[ 100.685306] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,17)Quoted 1 line
[ 100.685518] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0014/0001/0000 [out] st=0
Quoted 1 line
[ 100.685544] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,20)Quoted 1 line
[ 100.698539] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/05/0003/0000/0000 [out] st=0
Quoted 1 line
[ 100.698568] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet,captured speed 3
Quoted 1 line
[ 100.698585] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Gotaddress 3
Quoted 1 line
[ 100.714314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.714339] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.714354] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.729165] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.729195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.729227] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.733627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.733658] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.733690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.738363] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.738391] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.738427] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.742195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0029 [in] st=0
Quoted 1 line
[ 100.742225] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.742262] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.750944] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.750972] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751400] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.751425] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751455] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751777] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.751803] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 2 lines
[ 100.751821] configfs-gadget gadget: high-speed config #1: c [ 100.757460] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling[in] intr num 1 maxpacket=11
Quoted 1 line
[ 100.757502] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling[out] intr num 2 maxpacket=11
Quoted 1 line
[ 100.757549] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.820566] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/08/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.820594] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.820621] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821026] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packeta1/03/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.821050] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821076] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821397] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/0b/0000/0000/0000 [out] st=0
Quoted 1 line
[ 100.821422] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821451] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821643] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.821666] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821685] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 3 lines
[ 100.821697] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.821735] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.913006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.913034] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.913056] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 2 lines
[ 100.913067] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.946228] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.946257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.946274] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.946645] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 11 lines
[ 100.946672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 399.741059] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 399.741081] configfs-gadget gadget: suspendBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Thursday, Oct 25, 2018 6:42 AM
To: "Joel Stanley"<[email protected]>; "xiuzhi"<[email protected]>;
Cc: "a.filippov"<[email protected]>; "OpenBMCMaillist"<[email protected]>;
Quoted 5 lines
Subject: Re: VHUB didn't work on AST2500
Quoted 2 lines · Joel Stanley
Quoted 1 line · xiuzhi
I am porting obmc-ikvm to my hardware platform. The host screen
can be seen by vncviewer , but the mouse and keyboard didn't work on AST2500
Quoted 1 line
Quoted 1 line
Quoted 1 line
. Only the keys ';' , 'Enter', '1','2','3','4' work. others
keyinput will deadlock the host screen .
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
The kernel error log:
[ 99.326586] configfs-gadget gadget: high-speed config #1: c [ 99.403704] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 1 line
Quoted 1 line
Quoted 1 line
[ 99.492831] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 19 lines
Quoted 6 lines
Quoted 4 lines
The kernel version is : video-dev5,
commit2acbc35adcfe15971b701770e1105276a18da9f7Who can give me some suggestions to debug it?
Ben, do you have any advice?
I need to know a bit more. What is used as a gadget driver on the BMC ?
I would probably need to reproduce with some added traces to the driver to figure out what's going on.
One first thing to try would be a run with
CONFIG_USB_GADGET_DEBUGalong with some indication of what actions happen corresponding to what part of the log (ie, press key 'a' etc...).Cheers,
Ben.
Quoted 54 lines · Benjamin Herrenschmidt
Quoted 3 lines · xiuzhi
Hi Ben, Andrew,
I found the reason is that the key values are different between usb-vhub keyboard and physical keyboard. The vhub key value has one more byte than physical. and it seemed that vhub mouse uses keyboard channel, the BIOS can receive values from vhub mouse even if BIOS closed the mouse driver.
1, When the vhub mouse moves from ikvm, the vhub mouse sends out 6 bytes data to keyboard channel:vhub itself just passes the data that's coming from the HID gadget driver, I don't know much about how it construct packets or is configured, you may want to look into it.
Ben.
Quoted 44 lines
02 00 50 14 CE 22
02 00 B0 0E E8 20
02 00 48 08 96 1E
..........
2, The first byte of data sent by the vhub keyboard value is incorrect. The first byte is 01, which means that the control key is pressed from the physical keyboard view.
1) using vhub keyboard
Presses the key 'a' , BIOS receives data:01 00 00 04 00 00 00 00
Release key 'a' ,BIOS receives data:
01 00 00 00 00 00 00 00
Press 'Control' +'a' ,BIOS receives data:
01 01 00 04 00 00 00 00
Press the key'1' ,BIOS receives data:01 00 1E 00 00 00 00
Release key'1'usb, BIOS receives data:
01 00 00 00 00 00 00
2) using physical keyboard
Press the key 'a' ,BIOS receives data:
00 00 04 00 00 00 00 00Release key 'a' usb ,BIOS receives data::
00 00 00 00 00 00 00 00
Press 'Control' + 'a' ,BIOS receives data:
01 00 04 00 00 00 00 00
Press the key '1' ,BIOS receives data:00 00 1E 00 00 00 00 00
Release key '1' ,BIOS receives data:
00 00 00 00 00 00 00 00
Why does the vhub keyboard has the extra first byte '01'? Why vhub mouse use keyboard channel to transfer data?
It's a combined pointer and keyboard HID device. This isn't ideal, but I had more problems trying to use 2 separate HID devices actually.
01 is the device code for the keyboard, 02 is the device code for the pointer. HID standard allows that byte as the identifier for the report I think. See the create_usbhid.sh script packaged with the ikvm application. If you just want a keyboard, you could modify the descriptor sent to the gadget to just send keyboard.
Thanks,
Eddie
Quoted 778 lines
Quoted 777 lines
Best,
xiuzhi
------------------ Original ------------------
From: "Benjamin Herrenschmidte";<[email protected]>;
Send time: Monday, Nov 5, 2018 7:09 AM
To: "xiuzhi"<[email protected]>; "Andrew.Jeffery"<[email protected]>; "EddieJames"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 10 lines · xiuzhi
Hi Ben,
Did you reproduce this issue?
I found this issue is related to the host UEFI BIOS usb driver last week.
My host BIOS is cloned from udk2017 (www.uefi.org) .
The ikvm mouse and keyboard work when the BIOS runs on legacy mode
and will fail on UEFI mode.
I also compared the AMI BMC and OpenBMC.
The AMI BMC ikvm (version is r11) works on this problematic BIOS ,while OpenBMC will fail on the same one . The OpenBMC ikvm works on legacy mode ,and fails on UEFI mode.
Do you have any suggestions ?That's good to know any explains why I cannot reproduce as I don't have an UEFI system to test with.
I suspect something the UEFI BIOS does that upsets the Linux USB gadget stack.
I could debug this if I had access to a system, either physically here or remotely, where I can remotely install/netboot BMC kernels (so I would probably need a serial connection to the BMC and a PDU), any suggestion on how to do that ?
Otherwise, would there be a way to reproduce that with the x86 running in qemu ? (plugging the AST2500 eval board USB into the host and passing it through for example) ?
Cheers,
Ben.Quoted 738 lines
Best,
Xiuzhi
Hi Eddie,
The new obmc-ikvm has an new issue which got from https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/13888/
The number key 0-9 can input at the first BMC boot start-ipkvm.service.
It can't input any key when I restart the host ,and restart the start-ipkvm.service because of host screen resolution changed :
systemctl restart start-ipkvm.service
dmesg log:[ 144.990545] aspeed-video 1e700000.video: resolution changed; resetting [ 145.135654] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 145.135672] configfs-gadget gadget: suspend [ 146.020671] aspeed-video 1e700000.video: timed out on 1st mode detect [ 146.027154] aspeed-video 1e700000.video: resolution changed; couldn't get new resolution [ 267.098598] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 267.098623] configfs-gadget gadget: resume [ 267.098642] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 267.098650] configfs-gadget gadget: suspend [ 267.241258] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 267.241292] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 267.241308] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 267.262265] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 267.262293] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.266784] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 267.266805] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.271552] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 267.271585] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.275390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 267.275422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.284132] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 267.284475] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 267.284850] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 267.318337] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 267.318370] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.318723] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 267.318749] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318765] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.322862] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 267.322892] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 267.323093] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 267.323121] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 267.323343] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 267.323368] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 267.323595] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 267.323622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 267.323843] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 267.323870] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 267.344036] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.344069] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 267.481060] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.481091] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.481108] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 267.481446] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 267.481468] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 267.596168] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 267.596202] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 267.596217] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 267.596237] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -> 0011 (C=0) [ 267.596251] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at known speed of bound device, resetting... [ 267.596259] configfs-gadget gadget: reset config [ 267.596275] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Disabling ! [ 267.596288] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Nuking [ 267.596307] configfs-gadget gadget: End Point Request ERROR: -108 [ 267.602439] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Disabling ! [ 267.602458] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Nuking [ 267.602496] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -> 0403 (C=1) [ 267.622677] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.622710] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.622729] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 267.623097] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 267.623127] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 267.623344] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 267.623373] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 267.636359] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=2 [ 267.636389] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 wrong state [ 267.636402] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636412] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636423] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 267.653534] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.653566] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.653582] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.673140] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.673159] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673596] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.673622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi
Hi Andrew,
Sorry , the pinctrl error was not caused by uart-render-controller .
The reason is I definded a wrong gpio pin GPIOI3 (It is pin67) in filerecipes-phosphor/sekleton/obmc-libobmc-intfgpio_defs.json.The error message dispeared after I removed the pin definition. Now, the error of character key inputting still exists as well .
Best,
xiuzhi
Hi Andrew,Quoted 9 lines
Quoted 8 lines
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?
it was caused by uart-render-controller.service:
"
ExecStart=/usr/sbin/obmc-uart-render-controller \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \
fbterm.service
"
fbterm is related to keyinput.
AST2500 only support up to 228 gpio pins,but the error message read gpio:347 ,I don't know why ?Best,
Xiuzhi
------------------ Original ------------------
From: "Andrew.Jeffery";<[email protected]>;
Send time: Sunday, Oct 28, 2018 3:02 PM
To: "xiuzhi"<[email protected]>; "Benjamin Herrenschmidt"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 51 lines · xiuzhi
Hi Ben, Eddie,
I update the kernel,libvncserver,obmc-ikvm source to the latest git
commit numbers.
Now I can input number key 0-9, but still can't input any character key a-z .
1)kernel:
KSRC ?= "git://github.com/eddiejames/linux;protocol=git;branch=${KBRANCH}"
KBRANCH ?= "video-dev"LINUX_VERSION?= "4.18.12"
SRCREV = "b953727d56c4de63eb0fad1f079f41004e61d713"
and updated the defconfig,create_usbhid.sh as Eddie mentioned . 2)libvncserverSRC_URI= "git://github.com/LibVNC/libvncserver"SRCREV = "
ca2a5ac02fbbadd0a21fabba779c1ea69173d10b" 3)obmc-ikvmSRC_URI= "git://github.com/eddiejames/obmc-ikvm" SRCREV = "d548ee6c8f59c23552d61fb28b2ca2f20e6f3fe6"
4) I input key on host BIOS CLI:
"1234567890" 'Enter' : good ,can see them on host screen 'a' 'Enter':error ,see nothing
'b' 'Enter':error,see nothing
'c' 'Enter':error,see nothing "123456789"'Enter':good
The dmesg is :[ 57.002351] udc 1e6a0000.usb-vhub:p1: registering UDC driver [obmc_hid] [ 57.002452] configfs-gadget gadget: adding 'hid'/e5acc706 to config 'c'/7ef6bc13 [ 57.002488] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.002509] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 0 for addr 1 [ 57.013399] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0 for port EP1 [ 57.013435] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.013453] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 1 for addr 2 [ 57.018946] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1 for port EP2 [ 57.019463] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 57.019492] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 57.019512] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0000 -Quoted 1 line
0001 (C=1)
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67Quoted 2 lines
(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?/sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \ fbterm.serviceQuoted 555 lines
[ 100.115387] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.115411] configfs-gadget gadget: resume [ 100.115427] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.258057] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 100.258092] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 100.258107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 100.279075] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.279103] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.283632] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.283664] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.288371] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.288405] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.292205] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 100.292235] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.300948] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.301268] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.301640] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.335144] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 100.335178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335196] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.335527] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 100.335554] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335569] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.339672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 100.339703] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 100.339890] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 100.339912] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 100.340139] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 100.340160] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 100.340386] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 100.340404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 100.340637] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 100.340656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 100.360852] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.360884] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.500028] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.500062] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.500082] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 100.500404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 100.500435] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 100.615543] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 100.615579] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 100.615594] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.615612] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -Quoted 1 line
0011 (C=0)
[ 100.615626] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknown speed of disabled device, enabling... [ 100.615643] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -Quoted 1 line
0403 (C=1)
[ 100.635854] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.635885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.635903] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 100.636271] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 100.636299] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 100.636515] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 100.636540] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 100.649529] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=0 [ 100.649564] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet, captured speed 3 [ 100.649580] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Got address 3 [ 100.665314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.665345] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.665363] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.680170] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.680200] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.680234] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.684627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.684657] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.684690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.689471] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.689500] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.689538] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.693198] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0029 [in] st=0 [ 100.693231] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.693267] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.701949] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.701983] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702020] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.702432] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702466] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702774] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.702799] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702818] configfs-gadget gadget: high-speed config #1: c [ 100.708470] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling [in] intr num 1 maxpacket=11 [ 100.708512] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling [out] intr num 2 maxpacket=11 [ 100.708565] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.777585] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/08/0000/0000/0001 [in] st=0 [ 100.777619] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.777649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778029] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet a1/03/0000/0000/0001 [in] st=0 [ 100.778055] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778085] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/0b/0000/0000/0000 [out] st=0 [ 100.778428] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778457] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.778672] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778692] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.778704] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.778746] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.859563] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.859592] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.859618] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.859633] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.892835] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.892866] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.892882] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.893278] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.893305] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Saturday, Oct 27, 2018 7:55 AM
To: "xiuzhi"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 4 lines · xiuzhi
Hi Eddie,
Thanks for your reply.
It seemd that the error was caused by the version dismatch of kernel ,libvncserver ,obmc-ikvm and vnc client. Would you like to give me your git commits numbers of them?It's still a very strange error.
Once everything is up to date, let me know if it occurs again, there's something not right going on in the vhub driver causing that state mismatch error, it shouldn't happen. But I haven't managed to reproduce it here.
Cheers,
Ben.Quoted 327 lines
Best,
xiuzhiQuoted 16 lines · xiuzhi
Hi Ben,
I use vncviewer , xtightvncviewer 1.3.9-6.4ubuntu1.
And I also tested the ikvm by webui vnc(_https://gerrit.openbmc-project.xyz/#/c/openbmc/phosphor-webui/+/10268/_) ,the same errors occured.
The same source code obmc-ikvm and this kernel branch video-dev5 works on my other AST2400 hardware machine.
I remembered only one kernel version seemed to work on ast2500 ,I tested it six weeks ago .
the kernel version is:KBRANCH ?= "video-dev"
LINUX_VERSION?= "4.17.11" SRCREV="09a65900b2fc7aab9caf9d0dfabc7ba80525b1dd" the git repo is fromgit://github.com/eddiejames/linux/,Quoted 5 lines
https://gerrit.openbmc-project.xyz/#/c/openbmc/openbmc/+/11500/5/meta-openbmc-bsp/meta-aspeed/recipes-kernel/linux/linux-aspeed_git.bb
I want to test this kernel version ,but now this git repo is not available ,
I asked Eddiejames week ago, and get no response until now . It is so bad that I did not backup this kernel on my local machice.I never made any kernel changes related to USB in my github trees, as far as I know, so shouldn't be any difference. That original gerrit commit was purely for our testing purposes for our system... not really something I can support actively.
I have a number of commits pending review that you could try and pull in if you really need this now:
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-phosphor/+/13536/
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-aspeed/+/13541/
https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/12126/Use these in combination with the two commits at the top of my video-dev linux tree for your kernel.
Thanks,
EddieQuoted 285 lines
Best.
XiuzhiQuoted 4 lines · xiuzhi
Hi Ben,
I open theCONFIG_USB_GADGET_DEBUG.
and input the following keys by order:
';''Enter' :work good,can see ';' on host screenQuoted 8 lines
'a''Enter' :error,see anything on screen
'b''Enter' :error,see anything on screen
'1''Enter' :good
'2''Enter' :good
'3''Enter' :good
'4''Enter' :good
'5''Enter' :error deadlock
The log is:Can you tell me more about the userspace components you use to send those keys ? I'd like to try to reproduce here.
Quoted 1 line
[ 78.820671] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 78.828274] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Quoted 1 line
[ 80.698564] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 80.706166] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -
Quoted 1 line
[ 94.447816] udc 1e6a0000.usb-vhub:p1: registering UDC driver[
obmc_hid]Quoted 1 line
[ 94.447909] configfs-gadget gadget: adding 'hid'/15e5a204 toconfig 'c'/70dd0747
Quoted 2 lines
[ 94.447940] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.447958] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 0 for addr 1
Quoted 1 line
[ 94.448474] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0for port EP1
Quoted 2 lines
[ 94.448505] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.448522] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 1 for addr 2
Quoted 1 line
[ 94.448780] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1for port EP2
Quoted 3 lines
[ 94.449270] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 94.449297] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 94.449317] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0000 -> 0001 (C=1)
Quoted 4 lines
[ 100.158377] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.158400] configfs-gadget gadget: resume [ 100.158415] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.301048] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/05/0002/0000/0000 [out] st=0
Quoted 1 line
[ 100.301081] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000speed=high
Quoted 1 line
[ 100.301096] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS:Got address 2
Quoted 1 line
[ 100.322061] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.322090] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.326625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.326656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.331359] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.331392] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.335194] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0019 [in] st=0
Quoted 1 line
[ 100.335221] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.343939] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.344272] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.344647] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.378145] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0002 [in] st=0
Quoted 1 line
[ 100.378178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378195] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.378522] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0009 [in] st=0
Quoted 1 line
[ 100.378546] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378560] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.382665] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0001/0000 [out] st=0
Quoted 1 line
[ 100.382697] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,8)Quoted 1 line
[ 100.382896] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0002/0000 [out] st=0
Quoted 1 line
[ 100.382922] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(2,8)Quoted 1 line
[ 100.383148] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0003/0000 [out] st=0
Quoted 1 line
[ 100.383173] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(3,8)Quoted 1 line
[ 100.383396] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0004/0000 [out] st=0
Quoted 1 line
[ 100.383422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(4,8)Quoted 1 line
[ 100.383643] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0005/0000 [out] st=0
Quoted 1 line
[ 100.383668] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(5,8)Quoted 1 line
[ 100.403844] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 2 lines
[ 100.403871] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.549225] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.549257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.549275] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0101 change=0001
Quoted 1 line
[ 100.549651] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0010/0001/0000 [out] st=0
Quoted 1 line
[ 100.549681] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,16)Quoted 1 line
[ 100.664592] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0004/0001/0000 [out] st=0
Quoted 1 line
[ 100.664625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,4)Quoted 2 lines
[ 100.664639] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.664658] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0001 -> 0011 (C=0)
Quoted 1 line
[ 100.664672] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknownspeed of disabled device, enabling.
Quoted 1 line
[ 100.664689] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0011 -> 0403 (C=1)
Quoted 1 line
[ 100.684840] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.684867] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.684885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0012
Quoted 1 line
[ 100.685276] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0011/0001/0000 [out] st=0
Quoted 1 line
[ 100.685306] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,17)Quoted 1 line
[ 100.685518] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0014/0001/0000 [out] st=0
Quoted 1 line
[ 100.685544] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,20)Quoted 1 line
[ 100.698539] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/05/0003/0000/0000 [out] st=0
Quoted 1 line
[ 100.698568] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet,captured speed 3
Quoted 1 line
[ 100.698585] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Gotaddress 3
Quoted 1 line
[ 100.714314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.714339] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.714354] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.729165] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.729195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.729227] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.733627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.733658] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.733690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.738363] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.738391] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.738427] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.742195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0029 [in] st=0
Quoted 1 line
[ 100.742225] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.742262] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.750944] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.750972] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751400] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.751425] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751455] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751777] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.751803] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 2 lines
[ 100.751821] configfs-gadget gadget: high-speed config #1: c [ 100.757460] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling[in] intr num 1 maxpacket=11
Quoted 1 line
[ 100.757502] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling[out] intr num 2 maxpacket=11
Quoted 1 line
[ 100.757549] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.820566] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/08/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.820594] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.820621] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821026] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packeta1/03/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.821050] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821076] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821397] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/0b/0000/0000/0000 [out] st=0
Quoted 1 line
[ 100.821422] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821451] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821643] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.821666] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821685] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 3 lines
[ 100.821697] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.821735] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.913006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.913034] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.913056] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 2 lines
[ 100.913067] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.946228] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.946257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.946274] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.946645] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 11 lines
[ 100.946672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 399.741059] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 399.741081] configfs-gadget gadget: suspendBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Thursday, Oct 25, 2018 6:42 AM
To: "Joel Stanley"<[email protected]>; "xiuzhi"<[email protected]>;
Cc: "a.filippov"<[email protected]>; "OpenBMCMaillist"<[email protected]>;
Quoted 5 lines
Subject: Re: VHUB didn't work on AST2500
Quoted 2 lines · Joel Stanley
Quoted 1 line · xiuzhi
I am porting obmc-ikvm to my hardware platform. The host screen
can be seen by vncviewer , but the mouse and keyboard didn't work on AST2500
Quoted 1 line
Quoted 1 line
Quoted 1 line
. Only the keys ';' , 'Enter', '1','2','3','4' work. others
keyinput will deadlock the host screen .
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
The kernel error log:
[ 99.326586] configfs-gadget gadget: high-speed config #1: c [ 99.403704] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 1 line
Quoted 1 line
Quoted 1 line
[ 99.492831] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 17 lines
Quoted 5 lines
Quoted 4 lines
The kernel version is : video-dev5,
commit2acbc35adcfe15971b701770e1105276a18da9f7Who can give me some suggestions to debug it?
Ben, do you have any advice?
I need to know a bit more. What is used as a gadget driver on the BMC ?
I would probably need to reproduce with some added traces to the driver to figure out what's going on.
One first thing to try would be a run with
CONFIG_USB_GADGET_DEBUGalong with some indication of what actions happen corresponding to what part of the log (ie, press key 'a' etc...).Cheers,
Ben.
Hi Eddie,
Yes, the reason is that the vhub keyboard only support HID report protocol ,while UEFI BIOS (and most common BIOS) only support HID boot mode. It would be better if vhub were modified to support both HID report protocol and boot protocol
The UEFI BIOS try to request vhub switch to boot mode , but failed. The following is the UEFI code :
Request.RequestType = USB_HID_CLASS_SET_REQ_TYPE;
Request.Request = EFI_USB_SET_PROTOCOL_REQUEST;
Request.Value = Protocol; Request.Index = Interface; Request.Length = 0;
Result = UsbIo->UsbControlTransfer (
UsbIo,
&Request,
EfiUsbNoData,
PcdGet32 (PcdUsbTransferTimeoutValue),
NULL,
0,
&Status
);Best,
Xiuzhi
------------------ Original ------------------
From: "eajames";<[email protected]>;
Send time: Thursday, Dec 6, 2018 4:15 AM
To: "Benjamin Herrenschmidt"<[email protected]>; "xiuzhi"<[email protected]>; "Andrew.Jeffery"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: VHUB didn't work on AST2500
Quoted 54 lines · Benjamin Herrenschmidt
Quoted 3 lines · xiuzhi
Hi Ben, Andrew,
I found the reason is that the key values are different between usb-vhub keyboard and physical keyboard. The vhub key value has one more byte than physical. and it seemed that vhub mouse uses keyboard channel, the BIOS can receive values from vhub mouse even if BIOS closed the mouse driver.
1, When the vhub mouse moves from ikvm, the vhub mouse sends out 6 bytes data to keyboard channel:vhub itself just passes the data that's coming from the HID gadget driver, I don't know much about how it construct packets or is configured, you may want to look into it.
Ben.
Quoted 44 lines
02 00 50 14 CE 22
02 00 B0 0E E8 20
02 00 48 08 96 1E
..........
2, The first byte of data sent by the vhub keyboard value is incorrect. The first byte is 01, which means that the control key is pressed from the physical keyboard view.
1) using vhub keyboard
Presses the key 'a' , BIOS receives data:01 00 00 04 00 00 00 00
Release key 'a' ,BIOS receives data:
01 00 00 00 00 00 00 00
Press 'Control' +'a' ,BIOS receives data:
01 01 00 04 00 00 00 00
Press the key'1' ,BIOS receives data:01 00 1E 00 00 00 00
Release key'1'usb, BIOS receives data:
01 00 00 00 00 00 00
2) using physical keyboard
Press the key 'a' ,BIOS receives data:
00 00 04 00 00 00 00 00Release key 'a' usb ,BIOS receives data::
00 00 00 00 00 00 00 00
Press 'Control' + 'a' ,BIOS receives data:
01 00 04 00 00 00 00 00
Press the key '1' ,BIOS receives data:00 00 1E 00 00 00 00 00
Release key '1' ,BIOS receives data:
00 00 00 00 00 00 00 00
Why does the vhub keyboard has the extra first byte '01'? Why vhub mouse use keyboard channel to transfer data?
It's a combined pointer and keyboard HID device. This isn't ideal, but I had more problems trying to use 2 separate HID devices actually.
01 is the device code for the keyboard, 02 is the device code for the pointer. HID standard allows that byte as the identifier for the report I think. See the create_usbhid.sh script packaged with the ikvm application. If you just want a keyboard, you could modify the descriptor sent to the gadget to just send keyboard.
Thanks,
Eddie
Quoted 778 lines
Quoted 777 lines
Best,
xiuzhi
------------------ Original ------------------
From: "Benjamin Herrenschmidte";<[email protected]>;
Send time: Monday, Nov 5, 2018 7:09 AM
To: "xiuzhi"<[email protected]>; "Andrew.Jeffery"<[email protected]>; "EddieJames"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 10 lines · xiuzhi
Hi Ben,
Did you reproduce this issue?
I found this issue is related to the host UEFI BIOS usb driver last week.
My host BIOS is cloned from udk2017 (www.uefi.org) .
The ikvm mouse and keyboard work when the BIOS runs on legacy mode
and will fail on UEFI mode.
I also compared the AMI BMC and OpenBMC.
The AMI BMC ikvm (version is r11) works on this problematic BIOS ,while OpenBMC will fail on the same one . The OpenBMC ikvm works on legacy mode ,and fails on UEFI mode.
Do you have any suggestions ?That's good to know any explains why I cannot reproduce as I don't have an UEFI system to test with.
I suspect something the UEFI BIOS does that upsets the Linux USB gadget stack.
I could debug this if I had access to a system, either physically here or remotely, where I can remotely install/netboot BMC kernels (so I would probably need a serial connection to the BMC and a PDU), any suggestion on how to do that ?
Otherwise, would there be a way to reproduce that with the x86 running in qemu ? (plugging the AST2500 eval board USB into the host and passing it through for example) ?
Cheers,
Ben.Quoted 738 lines
Best,
Xiuzhi
Hi Eddie,
The new obmc-ikvm has an new issue which got from https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/13888/
The number key 0-9 can input at the first BMC boot start-ipkvm.service.
It can't input any key when I restart the host ,and restart the start-ipkvm.service because of host screen resolution changed :
systemctl restart start-ipkvm.service
dmesg log:[ 144.990545] aspeed-video 1e700000.video: resolution changed; resetting [ 145.135654] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 145.135672] configfs-gadget gadget: suspend [ 146.020671] aspeed-video 1e700000.video: timed out on 1st mode detect [ 146.027154] aspeed-video 1e700000.video: resolution changed; couldn't get new resolution [ 267.098598] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 267.098623] configfs-gadget gadget: resume [ 267.098642] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 267.098650] configfs-gadget gadget: suspend [ 267.241258] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 267.241292] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 267.241308] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 267.262265] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 267.262293] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.266784] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 267.266805] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.271552] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 267.271585] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.275390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 267.275422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.284132] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 267.284475] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 267.284850] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 267.318337] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 267.318370] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.318723] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 267.318749] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318765] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.322862] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 267.322892] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 267.323093] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 267.323121] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 267.323343] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 267.323368] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 267.323595] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 267.323622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 267.323843] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 267.323870] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 267.344036] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.344069] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 267.481060] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.481091] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.481108] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 267.481446] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 267.481468] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 267.596168] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 267.596202] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 267.596217] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 267.596237] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -> 0011 (C=0) [ 267.596251] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at known speed of bound device, resetting... [ 267.596259] configfs-gadget gadget: reset config [ 267.596275] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Disabling ! [ 267.596288] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Nuking [ 267.596307] configfs-gadget gadget: End Point Request ERROR: -108 [ 267.602439] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Disabling ! [ 267.602458] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Nuking [ 267.602496] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -> 0403 (C=1) [ 267.622677] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.622710] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.622729] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 267.623097] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 267.623127] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 267.623344] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 267.623373] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 267.636359] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=2 [ 267.636389] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 wrong state [ 267.636402] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636412] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636423] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 267.653534] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.653566] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.653582] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.673140] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.673159] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673596] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.673622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi
Hi Andrew,
Sorry , the pinctrl error was not caused by uart-render-controller .
The reason is I definded a wrong gpio pin GPIOI3 (It is pin67) in filerecipes-phosphor/sekleton/obmc-libobmc-intfgpio_defs.json.The error message dispeared after I removed the pin definition. Now, the error of character key inputting still exists as well .
Best,
xiuzhi
Hi Andrew,Quoted 9 lines
Quoted 8 lines
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?
it was caused by uart-render-controller.service:
"
ExecStart=/usr/sbin/obmc-uart-render-controller \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \
fbterm.service
"
fbterm is related to keyinput.
AST2500 only support up to 228 gpio pins,but the error message read gpio:347 ,I don't know why ?Best,
Xiuzhi
------------------ Original ------------------
From: "Andrew.Jeffery";<[email protected]>;
Send time: Sunday, Oct 28, 2018 3:02 PM
To: "xiuzhi"<[email protected]>; "Benjamin Herrenschmidt"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 51 lines · xiuzhi
Hi Ben, Eddie,
I update the kernel,libvncserver,obmc-ikvm source to the latest git
commit numbers.
Now I can input number key 0-9, but still can't input any character key a-z .
1)kernel:
KSRC ?= "git://github.com/eddiejames/linux;protocol=git;branch=${KBRANCH}"
KBRANCH ?= "video-dev"LINUX_VERSION?= "4.18.12"
SRCREV = "b953727d56c4de63eb0fad1f079f41004e61d713"
and updated the defconfig,create_usbhid.sh as Eddie mentioned . 2)libvncserverSRC_URI= "git://github.com/LibVNC/libvncserver"SRCREV = "
ca2a5ac02fbbadd0a21fabba779c1ea69173d10b" 3)obmc-ikvmSRC_URI= "git://github.com/eddiejames/obmc-ikvm" SRCREV = "d548ee6c8f59c23552d61fb28b2ca2f20e6f3fe6"
4) I input key on host BIOS CLI:
"1234567890" 'Enter' : good ,can see them on host screen 'a' 'Enter':error ,see nothing
'b' 'Enter':error,see nothing
'c' 'Enter':error,see nothing "123456789"'Enter':good
The dmesg is :[ 57.002351] udc 1e6a0000.usb-vhub:p1: registering UDC driver [obmc_hid] [ 57.002452] configfs-gadget gadget: adding 'hid'/e5acc706 to config 'c'/7ef6bc13 [ 57.002488] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.002509] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 0 for addr 1 [ 57.013399] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0 for port EP1 [ 57.013435] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.013453] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 1 for addr 2 [ 57.018946] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1 for port EP2 [ 57.019463] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 57.019492] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 57.019512] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0000 -Quoted 1 line
0001 (C=1)
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67Quoted 2 lines
(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?/sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \ fbterm.serviceQuoted 555 lines
[ 100.115387] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.115411] configfs-gadget gadget: resume [ 100.115427] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.258057] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 100.258092] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 100.258107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 100.279075] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.279103] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.283632] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.283664] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.288371] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.288405] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.292205] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 100.292235] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.300948] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.301268] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.301640] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.335144] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 100.335178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335196] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.335527] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 100.335554] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335569] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.339672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 100.339703] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 100.339890] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 100.339912] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 100.340139] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 100.340160] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 100.340386] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 100.340404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 100.340637] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 100.340656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 100.360852] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.360884] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.500028] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.500062] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.500082] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 100.500404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 100.500435] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 100.615543] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 100.615579] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 100.615594] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.615612] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -Quoted 1 line
0011 (C=0)
[ 100.615626] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknown speed of disabled device, enabling... [ 100.615643] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -Quoted 1 line
0403 (C=1)
[ 100.635854] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.635885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.635903] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 100.636271] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 100.636299] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 100.636515] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 100.636540] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 100.649529] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=0 [ 100.649564] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet, captured speed 3 [ 100.649580] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Got address 3 [ 100.665314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.665345] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.665363] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.680170] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.680200] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.680234] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.684627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.684657] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.684690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.689471] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.689500] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.689538] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.693198] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0029 [in] st=0 [ 100.693231] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.693267] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.701949] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.701983] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702020] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.702432] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702466] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702774] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.702799] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702818] configfs-gadget gadget: high-speed config #1: c [ 100.708470] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling [in] intr num 1 maxpacket=11 [ 100.708512] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling [out] intr num 2 maxpacket=11 [ 100.708565] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.777585] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/08/0000/0000/0001 [in] st=0 [ 100.777619] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.777649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778029] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet a1/03/0000/0000/0001 [in] st=0 [ 100.778055] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778085] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/0b/0000/0000/0000 [out] st=0 [ 100.778428] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778457] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.778672] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778692] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.778704] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.778746] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.859563] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.859592] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.859618] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.859633] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.892835] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.892866] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.892882] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.893278] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.893305] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Saturday, Oct 27, 2018 7:55 AM
To: "xiuzhi"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 4 lines · xiuzhi
Hi Eddie,
Thanks for your reply.
It seemd that the error was caused by the version dismatch of kernel ,libvncserver ,obmc-ikvm and vnc client. Would you like to give me your git commits numbers of them?It's still a very strange error.
Once everything is up to date, let me know if it occurs again, there's something not right going on in the vhub driver causing that state mismatch error, it shouldn't happen. But I haven't managed to reproduce it here.
Cheers,
Ben.Quoted 327 lines
Best,
xiuzhiQuoted 16 lines · xiuzhi
Hi Ben,
I use vncviewer , xtightvncviewer 1.3.9-6.4ubuntu1.
And I also tested the ikvm by webui vnc(_https://gerrit.openbmc-project.xyz/#/c/openbmc/phosphor-webui/+/10268/_) ,the same errors occured.
The same source code obmc-ikvm and this kernel branch video-dev5 works on my other AST2400 hardware machine.
I remembered only one kernel version seemed to work on ast2500 ,I tested it six weeks ago .
the kernel version is:KBRANCH ?= "video-dev"
LINUX_VERSION?= "4.17.11" SRCREV="09a65900b2fc7aab9caf9d0dfabc7ba80525b1dd" the git repo is fromgit://github.com/eddiejames/linux/,Quoted 5 lines
https://gerrit.openbmc-project.xyz/#/c/openbmc/openbmc/+/11500/5/meta-openbmc-bsp/meta-aspeed/recipes-kernel/linux/linux-aspeed_git.bb
I want to test this kernel version ,but now this git repo is not available ,
I asked Eddiejames week ago, and get no response until now . It is so bad that I did not backup this kernel on my local machice.I never made any kernel changes related to USB in my github trees, as far as I know, so shouldn't be any difference. That original gerrit commit was purely for our testing purposes for our system... not really something I can support actively.
I have a number of commits pending review that you could try and pull in if you really need this now:
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-phosphor/+/13536/
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-aspeed/+/13541/
https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/12126/Use these in combination with the two commits at the top of my video-dev linux tree for your kernel.
Thanks,
EddieQuoted 285 lines
Best.
XiuzhiQuoted 4 lines · xiuzhi
Hi Ben,
I open theCONFIG_USB_GADGET_DEBUG.
and input the following keys by order:
';''Enter' :work good,can see ';' on host screenQuoted 8 lines
'a''Enter' :error,see anything on screen
'b''Enter' :error,see anything on screen
'1''Enter' :good
'2''Enter' :good
'3''Enter' :good
'4''Enter' :good
'5''Enter' :error deadlock
The log is:Can you tell me more about the userspace components you use to send those keys ? I'd like to try to reproduce here.
Quoted 1 line
[ 78.820671] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 78.828274] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Quoted 1 line
[ 80.698564] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 80.706166] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -
Quoted 1 line
[ 94.447816] udc 1e6a0000.usb-vhub:p1: registering UDC driver[
obmc_hid]Quoted 1 line
[ 94.447909] configfs-gadget gadget: adding 'hid'/15e5a204 toconfig 'c'/70dd0747
Quoted 2 lines
[ 94.447940] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.447958] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 0 for addr 1
Quoted 1 line
[ 94.448474] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0for port EP1
Quoted 2 lines
[ 94.448505] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.448522] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 1 for addr 2
Quoted 1 line
[ 94.448780] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1for port EP2
Quoted 3 lines
[ 94.449270] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 94.449297] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 94.449317] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0000 -> 0001 (C=1)
Quoted 4 lines
[ 100.158377] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.158400] configfs-gadget gadget: resume [ 100.158415] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.301048] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/05/0002/0000/0000 [out] st=0
Quoted 1 line
[ 100.301081] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000speed=high
Quoted 1 line
[ 100.301096] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS:Got address 2
Quoted 1 line
[ 100.322061] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.322090] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.326625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.326656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.331359] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.331392] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.335194] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0019 [in] st=0
Quoted 1 line
[ 100.335221] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.343939] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.344272] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.344647] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.378145] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0002 [in] st=0
Quoted 1 line
[ 100.378178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378195] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.378522] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0009 [in] st=0
Quoted 1 line
[ 100.378546] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378560] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.382665] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0001/0000 [out] st=0
Quoted 1 line
[ 100.382697] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,8)Quoted 1 line
[ 100.382896] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0002/0000 [out] st=0
Quoted 1 line
[ 100.382922] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(2,8)Quoted 1 line
[ 100.383148] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0003/0000 [out] st=0
Quoted 1 line
[ 100.383173] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(3,8)Quoted 1 line
[ 100.383396] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0004/0000 [out] st=0
Quoted 1 line
[ 100.383422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(4,8)Quoted 1 line
[ 100.383643] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0005/0000 [out] st=0
Quoted 1 line
[ 100.383668] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(5,8)Quoted 1 line
[ 100.403844] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 2 lines
[ 100.403871] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.549225] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.549257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.549275] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0101 change=0001
Quoted 1 line
[ 100.549651] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0010/0001/0000 [out] st=0
Quoted 1 line
[ 100.549681] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,16)Quoted 1 line
[ 100.664592] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0004/0001/0000 [out] st=0
Quoted 1 line
[ 100.664625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,4)Quoted 2 lines
[ 100.664639] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.664658] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0001 -> 0011 (C=0)
Quoted 1 line
[ 100.664672] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknownspeed of disabled device, enabling.
Quoted 1 line
[ 100.664689] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0011 -> 0403 (C=1)
Quoted 1 line
[ 100.684840] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.684867] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.684885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0012
Quoted 1 line
[ 100.685276] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0011/0001/0000 [out] st=0
Quoted 1 line
[ 100.685306] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,17)Quoted 1 line
[ 100.685518] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0014/0001/0000 [out] st=0
Quoted 1 line
[ 100.685544] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,20)Quoted 1 line
[ 100.698539] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/05/0003/0000/0000 [out] st=0
Quoted 1 line
[ 100.698568] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet,captured speed 3
Quoted 1 line
[ 100.698585] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Gotaddress 3
Quoted 1 line
[ 100.714314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.714339] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.714354] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.729165] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.729195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.729227] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.733627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.733658] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.733690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.738363] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.738391] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.738427] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.742195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0029 [in] st=0
Quoted 1 line
[ 100.742225] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.742262] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.750944] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.750972] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751400] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.751425] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751455] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751777] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.751803] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 2 lines
[ 100.751821] configfs-gadget gadget: high-speed config #1: c [ 100.757460] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling[in] intr num 1 maxpacket=11
Quoted 1 line
[ 100.757502] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling[out] intr num 2 maxpacket=11
Quoted 1 line
[ 100.757549] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.820566] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/08/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.820594] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.820621] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821026] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packeta1/03/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.821050] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821076] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821397] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/0b/0000/0000/0000 [out] st=0
Quoted 1 line
[ 100.821422] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821451] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821643] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.821666] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821685] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 3 lines
[ 100.821697] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.821735] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.913006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.913034] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.913056] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 2 lines
[ 100.913067] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.946228] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.946257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.946274] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.946645] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 11 lines
[ 100.946672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 399.741059] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 399.741081] configfs-gadget gadget: suspendBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Thursday, Oct 25, 2018 6:42 AM
To: "Joel Stanley"<[email protected]>; "xiuzhi"<[email protected]>;
Cc: "a.filippov"<[email protected]>; "OpenBMCMaillist"<[email protected]>;
Quoted 5 lines
Subject: Re: VHUB didn't work on AST2500
Quoted 2 lines · Joel Stanley
Quoted 1 line · xiuzhi
I am porting obmc-ikvm to my hardware platform. The host screen
can be seen by vncviewer , but the mouse and keyboard didn't work on AST2500
Quoted 1 line
Quoted 1 line
Quoted 1 line
. Only the keys ';' , 'Enter', '1','2','3','4' work. others
keyinput will deadlock the host screen .
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
The kernel error log:
[ 99.326586] configfs-gadget gadget: high-speed config #1: c [ 99.403704] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 1 line
Quoted 1 line
Quoted 1 line
[ 99.492831] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 17 lines
Quoted 5 lines
Quoted 4 lines
The kernel version is : video-dev5,
commit2acbc35adcfe15971b701770e1105276a18da9f7Who can give me some suggestions to debug it?
Ben, do you have any advice?
I need to know a bit more. What is used as a gadget driver on the BMC ?
I would probably need to reproduce with some added traces to the driver to figure out what's going on.
One first thing to try would be a run with
CONFIG_USB_GADGET_DEBUGalong with some indication of what actions happen corresponding to what part of the log (ie, press key 'a' etc...).Cheers,
Ben.
Quoted 5 lines · xiuzhi
Hi Eddie,
Yes, the reason is that the vhub keyboard only support HID report
protocol ,while UEFI BIOS (and most common BIOS) only support HID
boot mode. It would be better if vhub were modified to support both HID report protocol and boot protocol
This has nothing to do with vhub. It's either in the kernel generic USB gadget f_hid.c code or in the userspace code that feeds it.
Quoted 877 lines
The UEFI BIOS try to request vhub switch to boot mode , but
failed. The following is the UEFI code :
Request.RequestType =USB_HID_CLASS_SET_REQ_TYPE;
Request.Request =EFI_USB_SET_PROTOCOL_REQUEST;Request.Value = Protocol; Request.Index = Interface; Request.Length = 0;Result =
UsbIo->UsbControlTransfer(UsbIo, &Request, EfiUsbNoData, PcdGet32 (PcdUsbTransferTimeoutValue), NULL, 0, &Status );Best,
Xiuzhi------------------ Original ------------------
From: "eajames";<[email protected]>;
Send time: Thursday, Dec 6, 2018 4:15 AM
To: "Benjamin Herrenschmidt"<[email protected]>; "xiuzhi"<[email protected]>; "Andrew.Jeffery"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: VHUB didn't work on AST2500Quoted 54 lines · Benjamin Herrenschmidt
Quoted 3 lines · xiuzhi
Hi Ben, Andrew,
I found the reason is that the key values are different between usb-vhub keyboard and physical keyboard. The vhub key value has one more byte than physical. and it seemed that vhub mouse uses keyboard channel, the BIOS can receive values from vhub mouse even if BIOS closed the mouse driver.
1, When the vhub mouse moves from ikvm, the vhub mouse sends out 6 bytes data to keyboard channel:vhub itself just passes the data that's coming from the HID gadget driver, I don't know much about how it construct packets or is configured, you may want to look into it.
Ben.
Quoted 44 lines
02 00 50 14 CE 22
02 00 B0 0E E8 20
02 00 48 08 96 1E
..........
2, The first byte of data sent by the vhub keyboard value is incorrect. The first byte is 01, which means that the control key is pressed from the physical keyboard view.
1) using vhub keyboard
Presses the key 'a' , BIOS receives data:01 00 00 04 00 00 00 00
Release key 'a' ,BIOS receives data:
01 00 00 00 00 00 00 00
Press 'Control' +'a' ,BIOS receives data:
01 01 00 04 00 00 00 00
Press the key'1' ,BIOS receives data:01 00 1E 00 00 00 00
Release key'1'usb, BIOS receives data:
01 00 00 00 00 00 00
2) using physical keyboard
Press the key 'a' ,BIOS receives data:
00 00 04 00 00 00 00 00Release key 'a' usb ,BIOS receives data::
00 00 00 00 00 00 00 00
Press 'Control' + 'a' ,BIOS receives data:
01 00 04 00 00 00 00 00
Press the key '1' ,BIOS receives data:00 00 1E 00 00 00 00 00
Release key '1' ,BIOS receives data:
00 00 00 00 00 00 00 00
Why does the vhub keyboard has the extra first byte '01'? Why vhub mouse use keyboard channel to transfer data?It's a combined pointer and keyboard HID device. This isn't ideal, but I had more problems trying to use 2 separate HID devices actually.
01 is the device code for the keyboard, 02 is the device code for the pointer. HID standard allows that byte as the identifier for the report I think. See the
create_usbhid.shscript packaged with the ikvm application. If you just want a keyboard, you could modify the descriptor sent to the gadget to just send keyboard.Thanks,
EddieQuoted 778 lines
Quoted 777 lines
Best,
xiuzhi
------------------ Original ------------------
From: "Benjamin Herrenschmidte";<[email protected]>;
Send time: Monday, Nov 5, 2018 7:09 AM
To: "xiuzhi"<[email protected]>; "Andrew.Jeffery"<[email protected]>; "EddieJames"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 10 lines · xiuzhi
Hi Ben,
Did you reproduce this issue?
I found this issue is related to the host UEFI BIOS usb driver last week.
My host BIOS is cloned from udk2017 (www.uefi.org) .
The ikvm mouse and keyboard work when the BIOS runs on legacy mode
and will fail on UEFI mode.
I also compared the AMI BMC and OpenBMC.
The AMI BMC ikvm (version is r11) works on this problematic BIOS ,while OpenBMC will fail on the same one . The OpenBMC ikvm works on legacy mode ,and fails on UEFI mode.
Do you have any suggestions ?That's good to know any explains why I cannot reproduce as I don't have an UEFI system to test with.
I suspect something the UEFI BIOS does that upsets the Linux USB gadget stack.
I could debug this if I had access to a system, either physically here or remotely, where I can remotely install/netboot BMC kernels (so I would probably need a serial connection to the BMC and a PDU), any suggestion on how to do that ?
Otherwise, would there be a way to reproduce that with the x86 running in qemu ? (plugging the AST2500 eval board USB into the host and passing it through for example) ?
Cheers,
Ben.Quoted 738 lines
Best,
Xiuzhi
Hi Eddie,
The new obmc-ikvm has an new issue which got from https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/13888/
The number key 0-9 can input at the first BMC boot start-ipkvm.service.
It can't input any key when I restart the host ,and restart the start-ipkvm.service because of host screen resolution changed :
systemctl restart start-ipkvm.service
dmesg log:[ 144.990545] aspeed-video 1e700000.video: resolution changed; resetting [ 145.135654] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 145.135672] configfs-gadget gadget: suspend [ 146.020671] aspeed-video 1e700000.video: timed out on 1st mode detect [ 146.027154] aspeed-video 1e700000.video: resolution changed; couldn't get new resolution [ 267.098598] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 267.098623] configfs-gadget gadget: resume [ 267.098642] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 267.098650] configfs-gadget gadget: suspend [ 267.241258] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 267.241292] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 267.241308] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 267.262265] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 267.262293] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.266784] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 267.266805] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 267.271552] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 267.271585] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.275390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 267.275422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 267.284132] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 267.284475] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 267.284850] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 267.318337] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 267.318370] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318390] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.318723] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 267.318749] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 267.318765] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 267.322862] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 267.322892] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 267.323093] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 267.323121] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 267.323343] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 267.323368] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 267.323595] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 267.323622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 267.323843] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 267.323870] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 267.344036] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.344069] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 267.481060] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.481091] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.481108] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 267.481446] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 267.481468] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 267.596168] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 267.596202] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 267.596217] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 267.596237] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -> 0011 (C=0) [ 267.596251] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at known speed of bound device, resetting... [ 267.596259] configfs-gadget gadget: reset config [ 267.596275] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Disabling ! [ 267.596288] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Nuking [ 267.596307] configfs-gadget gadget: End Point Request ERROR: -108 [ 267.602439] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Disabling ! [ 267.602458] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Nuking [ 267.602496] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -> 0403 (C=1) [ 267.622677] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.622710] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.622729] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 267.623097] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 267.623127] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 267.623344] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 267.623373] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 267.636359] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=2 [ 267.636389] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 wrong state [ 267.636402] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636412] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 Nuking [ 267.636423] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 267.653534] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.653566] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.653582] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 267.673140] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 267.673159] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 267.673596] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 267.673622] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi
Hi Andrew,
Sorry , the pinctrl error was not caused by uart-render-controller .
The reason is I definded a wrong gpio pin GPIOI3 (It is pin67) in filerecipes-phosphor/sekleton/obmc-libobmc-intfgpio_defs.json.The error message dispeared after I removed the pin definition. Now, the error of character key inputting still exists as well .
Best,
xiuzhi
Hi Andrew,Quoted 9 lines
Quoted 8 lines
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?
it was caused by uart-render-controller.service:
"
ExecStart=/usr/sbin/obmc-uart-render-controller \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \
fbterm.service
"
fbterm is related to keyinput.
AST2500 only support up to 228 gpio pins,but the error message read gpio:347 ,I don't know why ?Best,
Xiuzhi
------------------ Original ------------------
From: "Andrew.Jeffery";<[email protected]>;
Send time: Sunday, Oct 28, 2018 3:02 PM
To: "xiuzhi"<[email protected]>; "Benjamin Herrenschmidt"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 51 lines · xiuzhi
Hi Ben, Eddie,
I update the kernel,libvncserver,obmc-ikvm source to the latest git
commit numbers.
Now I can input number key 0-9, but still can't input any character key a-z .
1)kernel:
KSRC ?= "git://github.com/eddiejames/linux;protocol=git;branch=${KBRANCH}"
KBRANCH ?= "video-dev"LINUX_VERSION?= "4.18.12"
SRCREV = "b953727d56c4de63eb0fad1f079f41004e61d713"
and updated the defconfig,create_usbhid.sh as Eddie mentioned . 2)libvncserverSRC_URI= "git://github.com/LibVNC/libvncserver"SRCREV = "
ca2a5ac02fbbadd0a21fabba779c1ea69173d10b" 3)obmc-ikvmSRC_URI= "git://github.com/eddiejames/obmc-ikvm" SRCREV = "d548ee6c8f59c23552d61fb28b2ca2f20e6f3fe6"
4) I input key on host BIOS CLI:
"1234567890" 'Enter' : good ,can see them on host screen 'a' 'Enter':error ,see nothing
'b' 'Enter':error,see nothing
'c' 'Enter':error,see nothing "123456789"'Enter':good
The dmesg is :[ 57.002351] udc 1e6a0000.usb-vhub:p1: registering UDC driver [obmc_hid] [ 57.002452] configfs-gadget gadget: adding 'hid'/e5acc706 to config 'c'/7ef6bc13 [ 57.002488] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.002509] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 0 for addr 1 [ 57.013399] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0 for port EP1 [ 57.013435] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 57.013453] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating gen EP 1 for addr 2 [ 57.018946] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1 for port EP2 [ 57.019463] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 57.019492] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 57.019512] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0000 -Quoted 1 line
0001 (C=1)
[ 66.751716] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 66.759322] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67 (1e780000.gpio:347) status -1 [ 68.577538] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request() failed for pin 67 [ 68.585288] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67Quoted 2 lines
(1e780000.gpio:347) status -1
Out of curiousity, what is causing the pinctrl failure? Do you have a mux clash?/sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/vga0 \ /sys/devices/platform/ahb/ahb:apb/1e6e2000.syscon/1e6e2000.syscon:scratch/dac_mux \ fbterm.serviceQuoted 555 lines
[ 100.115387] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.115411] configfs-gadget gadget: resume [ 100.115427] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.258057] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/05/0002/0000/0000 [out] st=0 [ 100.258092] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000 speed=high [ 100.258107] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS: Got address 2 [ 100.279075] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.279103] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.283632] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.283664] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:1) [ 100.288371] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.288405] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.292205] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0200/0000/0019 [in] st=0 [ 100.292235] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:2) [ 100.300948] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.301268] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.301640] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.335144] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0002 [in] st=0 [ 100.335178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335196] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.335527] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/06/2900/0000/0009 [in] st=0 [ 100.335554] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubDescriptor(0) [ 100.335569] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GET_DESCRIPTOR(type:41) [ 100.339672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0001/0000 [out] st=0 [ 100.339703] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,8) [ 100.339890] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0002/0000 [out] st=0 [ 100.339912] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(2,8) [ 100.340139] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0003/0000 [out] st=0 [ 100.340160] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(3,8) [ 100.340386] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0004/0000 [out] st=0 [ 100.340404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(4,8) [ 100.340637] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0008/0005/0000 [out] st=0 [ 100.340656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(5,8) [ 100.360852] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.360884] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.500028] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.500062] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.500082] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0101 change=0001 [ 100.500404] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0010/0001/0000 [out] st=0 [ 100.500435] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,16) [ 100.615543] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/03/0004/0001/0000 [out] st=0 [ 100.615579] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SetPortFeature(1,4) [ 100.615594] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.615612] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0001 -Quoted 1 line
0011 (C=0)
[ 100.615626] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknown speed of disabled device, enabling... [ 100.615643] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status 0011 -Quoted 1 line
0403 (C=1)
[ 100.635854] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.635885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.635903] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0012 [ 100.636271] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0011/0001/0000 [out] st=0 [ 100.636299] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,17) [ 100.636515] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet 23/01/0014/0001/0000 [out] st=0 [ 100.636540] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 ClearPortFeature(1,20) [ 100.649529] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/05/0003/0000/0000 [out] st=0 [ 100.649564] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet, captured speed 3 [ 100.649580] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Got address 3 [ 100.665314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.665345] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.665363] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.680170] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0008 [in] st=0 [ 100.680200] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.680234] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.684627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0100/0000/0012 [in] st=0 [ 100.684657] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.684690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.689471] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0008 [in] st=0 [ 100.689500] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.689538] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.693198] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0200/0000/0029 [in] st=0 [ 100.693231] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.693267] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.701949] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0002 [in] st=0 [ 100.701983] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702020] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/06/0300/0000/0004 [in] st=0 [ 100.702432] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702466] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.702774] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 00/09/0001/0000/0000 [out] st=0 [ 100.702799] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.702818] configfs-gadget gadget: high-speed config #1: c [ 100.708470] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling [in] intr num 1 maxpacket=11 [ 100.708512] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling [out] intr num 2 maxpacket=11 [ 100.708565] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.777585] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 80/08/0000/0000/0001 [in] st=0 [ 100.777619] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.777649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778029] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet a1/03/0000/0000/0001 [in] st=0 [ 100.778055] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778085] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778403] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/0b/0000/0000/0000 [out] st=0 [ 100.778428] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778457] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned 0 [ 100.778649] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.778672] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.778692] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.778704] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.778746] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.859563] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet 21/09/0200/0000/0001 [out] st=0 [ 100.859592] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwarding to gadget... [ 100.859618] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driver returned -95 [ 100.859633] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.892835] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a3/00/0000/0001/0004 [in] st=0 [ 100.892866] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.892882] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 port status=0503 change=0000 [ 100.893278] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet a0/00/0000/0000/0004 [in] st=0 [ 100.893305] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatusBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Saturday, Oct 27, 2018 7:55 AM
To: "xiuzhi"<[email protected]>; "Eddie James"<[email protected]>; "Joel Stanley"<[email protected]>;
Cc: "openbmc"<[email protected]>; "Alexander A. Filippov"<[email protected]>;
Subject: Re: Re: VHUB didn't work on AST2500Quoted 4 lines · xiuzhi
Hi Eddie,
Thanks for your reply.
It seemd that the error was caused by the version dismatch of kernel ,libvncserver ,obmc-ikvm and vnc client. Would you like to give me your git commits numbers of them?It's still a very strange error.
Once everything is up to date, let me know if it occurs again, there's something not right going on in the vhub driver causing that state mismatch error, it shouldn't happen. But I haven't managed to reproduce it here.
Cheers,
Ben.Quoted 327 lines
Best,
xiuzhiQuoted 16 lines · xiuzhi
Hi Ben,
I use vncviewer , xtightvncviewer 1.3.9-6.4ubuntu1.
And I also tested the ikvm by webui vnc(_https://gerrit.openbmc-project.xyz/#/c/openbmc/phosphor-webui/+/10268/_) ,the same errors occured.
The same source code obmc-ikvm and this kernel branch video-dev5 works on my other AST2400 hardware machine.
I remembered only one kernel version seemed to work on ast2500 ,I tested it six weeks ago .
the kernel version is:KBRANCH ?= "video-dev"
LINUX_VERSION?= "4.17.11" SRCREV="09a65900b2fc7aab9caf9d0dfabc7ba80525b1dd" the git repo is fromgit://github.com/eddiejames/linux/,Quoted 5 lines
https://gerrit.openbmc-project.xyz/#/c/openbmc/openbmc/+/11500/5/meta-openbmc-bsp/meta-aspeed/recipes-kernel/linux/linux-aspeed_git.bb
I want to test this kernel version ,but now this git repo is not available ,
I asked Eddiejames week ago, and get no response until now . It is so bad that I did not backup this kernel on my local machice.I never made any kernel changes related to USB in my github trees, as far as I know, so shouldn't be any difference. That original gerrit commit was purely for our testing purposes for our system... not really something I can support actively.
I have a number of commits pending review that you could try and pull in if you really need this now:
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-phosphor/+/13536/
https://gerrit.openbmc-project.xyz/#/c/openbmc/meta-aspeed/+/13541/
https://gerrit.openbmc-project.xyz/#/c/openbmc/obmc-ikvm/+/12126/Use these in combination with the two commits at the top of my video-dev linux tree for your kernel.
Thanks,
EddieQuoted 285 lines
Best.
XiuzhiQuoted 4 lines · xiuzhi
Hi Ben,
I open theCONFIG_USB_GADGET_DEBUG.
and input the following keys by order:
';''Enter' :work good,can see ';' on host screenQuoted 8 lines
'a''Enter' :error,see anything on screen
'b''Enter' :error,see anything on screen
'1''Enter' :good
'2''Enter' :good
'3''Enter' :good
'4''Enter' :good
'5''Enter' :error deadlock
The log is:Can you tell me more about the userspace components you use to send those keys ? I'd like to try to reproduce here.
Quoted 1 line
[ 78.820671] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 78.828274] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -1
Quoted 1 line
[ 80.698564] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request()failed for pin 67
Quoted 1 line
[ 80.706166] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: pin-67(1e780000.gpio:347) status -
Quoted 1 line
[ 94.447816] udc 1e6a0000.usb-vhub:p1: registering UDC driver[
obmc_hid]Quoted 1 line
[ 94.447909] configfs-gadget gadget: adding 'hid'/15e5a204 toconfig 'c'/70dd0747
Quoted 2 lines
[ 94.447940] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.447958] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 0 for addr 1
Quoted 1 line
[ 94.448474] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#0for port EP1
Quoted 2 lines
[ 94.448505] aspeed_vhub 1e6a0000.usb-vhub: port1 Match EP type 3 [ 94.448522] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocating genEP 1 for addr 2
Quoted 1 line
[ 94.448780] aspeed_vhub 1e6a0000.usb-vhub: port1 Allocated epn#1for port EP2
Quoted 3 lines
[ 94.449270] aspeed_vhub 1e6a0000.usb-vhub: port1 start [ 94.449297] aspeed_vhub 1e6a0000.usb-vhub: port1 pullup(1) [ 94.449317] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0000 -> 0001 (C=1)
Quoted 4 lines
[ 100.158377] aspeed_vhub 1e6a0000.usb-vhub: USB bus resume [ 100.158400] configfs-gadget gadget: resume [ 100.158415] aspeed_vhub 1e6a0000.usb-vhub: USB bus reset [ 100.301048] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/05/0002/0000/0000 [out] st=0
Quoted 1 line
[ 100.301081] aspeed_vhub 1e6a0000.usb-vhub: USB status=0b100000speed=high
Quoted 1 line
[ 100.301096] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SET_ADDRESS:Got address 2
Quoted 1 line
[ 100.322061] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.322090] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.326625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.326656] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:1)Quoted 1 line
[ 100.331359] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.331392] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.335194] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0200/0000/0019 [in] st=0
Quoted 1 line
[ 100.335221] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:2)Quoted 1 line
[ 100.343939] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.344272] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.344647] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.378145] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0002 [in] st=0
Quoted 1 line
[ 100.378178] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378195] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.378522] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/06/2900/0000/0009 [in] st=0
Quoted 1 line
[ 100.378546] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0GetHubDescriptor(0)
Quoted 1 line
[ 100.378560] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
GET_DESCRIPTOR(type:41)Quoted 1 line
[ 100.382665] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0001/0000 [out] st=0
Quoted 1 line
[ 100.382697] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,8)Quoted 1 line
[ 100.382896] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0002/0000 [out] st=0
Quoted 1 line
[ 100.382922] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(2,8)Quoted 1 line
[ 100.383148] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0003/0000 [out] st=0
Quoted 1 line
[ 100.383173] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(3,8)Quoted 1 line
[ 100.383396] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0004/0000 [out] st=0
Quoted 1 line
[ 100.383422] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(4,8)Quoted 1 line
[ 100.383643] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0008/0005/0000 [out] st=0
Quoted 1 line
[ 100.383668] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(5,8)Quoted 1 line
[ 100.403844] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 2 lines
[ 100.403871] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 100.549225] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.549257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.549275] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0101 change=0001
Quoted 1 line
[ 100.549651] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0010/0001/0000 [out] st=0
Quoted 1 line
[ 100.549681] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,16)Quoted 1 line
[ 100.664592] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/03/0004/0001/0000 [out] st=0
Quoted 1 line
[ 100.664625] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
SetPortFeature(1,4)Quoted 2 lines
[ 100.664639] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 Port reset ! [ 100.664658] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0001 -> 0011 (C=0)
Quoted 1 line
[ 100.664672] aspeed_vhub 1e6a0000.usb-vhub: port1 Reset at unknownspeed of disabled device, enabling.
Quoted 1 line
[ 100.664689] aspeed_vhub 1e6a0000.usb-vhub: port1 port 1 status0011 -> 0403 (C=1)
Quoted 1 line
[ 100.684840] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.684867] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.684885] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0012
Quoted 1 line
[ 100.685276] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0011/0001/0000 [out] st=0
Quoted 1 line
[ 100.685306] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,17)Quoted 1 line
[ 100.685518] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packet23/01/0014/0001/0000 [out] st=0
Quoted 1 line
[ 100.685544] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0
ClearPortFeature(1,20)Quoted 1 line
[ 100.698539] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/05/0003/0000/0000 [out] st=0
Quoted 1 line
[ 100.698568] aspeed_vhub 1e6a0000.usb-vhub: port1 fist packet,captured speed 3
Quoted 1 line
[ 100.698585] aspeed_vhub 1e6a0000.usb-vhub: port1 SET_ADDRESS: Gotaddress 3
Quoted 1 line
[ 100.714314] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.714339] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.714354] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.729165] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0008 [in] st=0
Quoted 1 line
[ 100.729195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.729227] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.733627] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0100/0000/0012 [in] st=0
Quoted 1 line
[ 100.733658] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.733690] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.738363] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0008 [in] st=0
Quoted 1 line
[ 100.738391] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.738427] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.742195] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0200/0000/0029 [in] st=0
Quoted 1 line
[ 100.742225] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.742262] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.750944] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0002 [in] st=0
Quoted 1 line
[ 100.750972] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751400] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/06/0300/0000/0004 [in] st=0
Quoted 1 line
[ 100.751425] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.751455] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.751777] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet00/09/0001/0000/0000 [out] st=0
Quoted 1 line
[ 100.751803] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 2 lines
[ 100.751821] configfs-gadget gadget: high-speed config #1: c [ 100.757460] aspeed_vhub 1e6a0000.usb-vhub: port1:EP1 Enabling[in] intr num 1 maxpacket=11
Quoted 1 line
[ 100.757502] aspeed_vhub 1e6a0000.usb-vhub: port1:EP2 Enabling[out] intr num 2 maxpacket=11
Quoted 1 line
[ 100.757549] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.820566] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet80/08/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.820594] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.820621] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821026] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packeta1/03/0000/0000/0001 [in] st=0
Quoted 1 line
[ 100.821050] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821076] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821397] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/0b/0000/0000/0000 [out] st=0
Quoted 1 line
[ 100.821422] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821451] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned 0
Quoted 1 line
[ 100.821643] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.821666] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.821685] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 3 lines
[ 100.821697] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.821735] aspeed_vhub 1e6a0000.usb-vhub: status direction mismatch [ 100.913006] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 SETUP packet21/09/0200/0000/0001 [out] st=0
Quoted 1 line
[ 100.913034] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 forwardingto gadget...
Quoted 1 line
[ 100.913056] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 driverreturned -95
Quoted 2 lines
[ 100.913067] aspeed_vhub 1e6a0000.usb-vhub: port1:EP0 stalling [ 100.946228] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta3/00/0000/0001/0004 [in] st=0
Quoted 2 lines
[ 100.946257] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetPortStatus(1) [ 100.946274] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 portstatus=0503 change=0000
Quoted 1 line
[ 100.946645] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 SETUP packeta0/00/0000/0000/0004 [in] st=0
Quoted 11 lines
[ 100.946672] aspeed_vhub 1e6a0000.usb-vhub: hub:EP0 GetHubStatus [ 399.741059] aspeed_vhub 1e6a0000.usb-vhub: USB bus suspend [ 399.741081] configfs-gadget gadget: suspendBest,
Xiuzhi------------------ Original ------------------
From: "Benjamin Herrenschmidt";<[email protected]>; Send time: Thursday, Oct 25, 2018 6:42 AM
To: "Joel Stanley"<[email protected]>; "xiuzhi"<[email protected]>;
Cc: "a.filippov"<[email protected]>; "OpenBMCMaillist"<[email protected]>;
Quoted 5 lines
Subject: Re: VHUB didn't work on AST2500
Quoted 2 lines · Joel Stanley
Quoted 1 line · xiuzhi
I am porting obmc-ikvm to my hardware platform. The host screen
can be seen by vncviewer , but the mouse and keyboard didn't work on AST2500
Quoted 1 line
Quoted 1 line
Quoted 1 line
. Only the keys ';' , 'Enter', '1','2','3','4' work. others
keyinput will deadlock the host screen .
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
The kernel error log:
[ 99.326586] configfs-gadget gadget: high-speed config #1: c [ 99.403704] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 1 line
Quoted 1 line
Quoted 1 line
[ 99.492831] aspeed_vhub 1e6a0000.usb-vhub: status directionmismatch
Quoted 17 lines
Quoted 5 lines
Quoted 4 lines
The kernel version is : video-dev5,
commit2acbc35adcfe15971b701770e1105276a18da9f7Who can give me some suggestions to debug it?
Ben, do you have any advice?
I need to know a bit more. What is used as a gadget driver on the BMC ?
I would probably need to reproduce with some added traces to the driver to figure out what's going on.
One first thing to try would be a run with
CONFIG_USB_GADGET_DEBUGalong with some indication of what actions happen corresponding to what part of the log (ie, press key 'a' etc...).Cheers,
Ben.