Skip to contentSkip to conversation

MAC#2 RGMII mode can't ping other IP address on AST2500

DISCUSSION xiuzhi 1 participant 1 message Sep 26, 2018

lore
Share & tools
lore

xiuzhi

author
#0 lore raw

Hi Andrew,

Quoted 13 lines · xiuzhi
Quoted 13 lines

Hi All,
My hardware set AST2500 MAC#2 on RGMII mode. the device is Broadcom
BCM54612, The PHY and control is good . But it can not ping other IP. The .dts file is:

&mac1 {

        status = "okay";

        pinctrl-names = "default";

        pinctrl-0 = <&pinctrl_rgmii2_default>;
Quoted 8 lines
Quoted 6 lines

};

The kernel boot info:

[    3.747357] ftgmac100 1e680000.ethernet: Error applying setting, 

reverse things back

The failure to apply the pinctrl configuration isn't going to help. Can you >please open an issue on GitHub, provide the full dmesg output and point >to the kernel tree and configuration you are building?

I created a new issue No 3388: https://github.com/openbmc/openbmc/issues/3388

Xiuzhi

Quoted 75 lines

Thanks,

Andrew

Quoted 70 lines
[    3.755351] ftgmac100 1e680000.ethernet: Generated random MAC address 

6a:ba:31:cd:e3:32

[    3.771891] libphy: ftgmac100_mdio: probed
[    3.776178] Generic PHY 1e680000.ethernet--1:00: attached PHY driver 

[Generic PHY] (mii_bus:phy_addr=1e680000.ethernet--1:00, irq=POLL)

[    3.799636] ftgmac100 1e680000.ethernet eth0: irq 19, mapped at 5ae85020

... ...

[ OK ] Found device /dev/aspeed-lpc-ctrl.

[ OK 17.494678] ftgmac100 1e680000.ethernet eth0: Link is Up -
100Mbps/Full - flow control rx/tx

m] Created slice[ 17.503871] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link
becomes ready

system-xyz.openbmc_project.led.controller.slice.

Starting Network Name Resolution...

[ OK ] Reached target System Time Synchronized.

......

The values of register SCU0C and SCU70 are correct, the values are:

#devmem 0x1e6e200C

0xFFDD7A8B, the bit 21 is 0(MAC#2 enable clock running) ,the bit 20 is 1

#dev mem 0x1e6e2070

0xF109F296 , the bit 7 is 1 (RGMII),the bit6 is 0

Execting the command "ifconfig eth0 up" log is:

root@romulus:~# ifconfig eth0 up  
[  274.978358] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
root@romulus:~# [  274.986878] ftgmac100 1e680000.ethernet eth0: Link is 
Up - 100Mbps/Full - flow control rx/tx
[  274.995944] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready 

My bmc ip is 192.168.120.141, it can't ping other IPs.

I also set the gateway. route add default gw 192.168.120.254. I trace the error "ftgmac100 1e680000.ethernet: Error applying setting, reverse things back" in file drivers/pinctrl/core.c
L1206
list_for_each_entry(setting, &stte->settings,node) switch(setting->type?{
case PIN_MAP_TYPE_MUX_GROUP

      ret = pinmux_enable_setting(setting); 
}

the ret value is -1
My kernel version is 4.17.14. The other kernel versions reproduce the same error.
What is wrong with it?

Xiuzhi