Skip to contentSkip to conversation

firewire: prefix modules with firewire- instead of fw-

RFC PATCH In review Stefan Richter 2 participants 2 messages May 25, 2007 Firewire

lore
Share & tools
lore
#0 lore raw

RFC PATCH 1/1 firewire: prefix modules with firewire- instead of fw-

Of course everybody immediately associates "fw-" with FireWire, not firmware or firewall or whatever. But "firewire-" has a nice ring to it too.

---

So everybody, do you prefer the longer names?

Alas this RFC is a little bit late before release, but perhaps not too late.

 drivers/firewire/Kconfig  |   14 +++++++-------
 drivers/firewire/Makefile |   12 +++++++-----
 2 files changed, 14 insertions(+), 12 deletions(-)
drivers/firewire/Kconfig +7 -7
Index: linux/drivers/firewire/Kconfig
===================================================================
@@ -18,7 +18,7 @@ config FIREWIRE
 	  your IEEE 1394 adapter.
 
 	  To compile this driver as a module, say M here: the module will be
-	  called fw-core.
+	  called firewire-core.
 
 	  This is the "JUJU" FireWire stack, an alternative implementation
 	  designed for robustness and simplicity.  You can build either this
@@ -34,11 +34,11 @@ config FIREWIRE_OHCI
 	  is the only chipset in use, so say Y here.
 
 	  To compile this driver as a module, say M here:  The module will be
-	  called fw-ohci.
+	  called firewire-ohci.
 
 	  If you also build ohci1394 of the classic IEEE 1394 driver stack,
-	  blacklist either ohci1394 or fw-ohci to let hotplug load the desired
-	  driver.
+	  blacklist either ohci1394 or firewire-ohci to let hotplug load the
+	  desired driver.
 
 config FIREWIRE_SBP2
 	tristate "Support for storage devices (SBP-2 protocol driver)"
@@ -50,12 +50,12 @@ config FIREWIRE_SBP2
 	  like scanners.
 
 	  To compile this driver as a module, say M here:  The module will be
-	  called fw-sbp2.
+	  called firewire-sbp2.
 
 	  You should also enable support for disks, CD-ROMs, etc. in the SCSI
 	  configuration section.
 
 	  If you also build sbp2 of the classic IEEE 1394 driver stack,
-	  blacklist either sbp2 or fw-sbp2 to let hotplug load the desired
-	  driver.
+	  blacklist either sbp2 or firewire-sbp2 to let hotplug load the
+	  desired driver.
 
drivers/firewire/Makefile +7 -5
Index: linux/drivers/firewire/Makefile
===================================================================
@@ -2,9 +2,11 @@
 # Makefile for the Linux IEEE 1394 implementation
 #
 
-fw-core-y += fw-card.o fw-topology.o fw-transaction.o fw-iso.o \
-	fw-device.o fw-cdev.o
+firewire-core-y += fw-card.o fw-topology.o fw-transaction.o fw-iso.o \
+                   fw-device.o fw-cdev.o
+firewire-ohci-y += fw-ohci.o
+firewire-sbp2-y += fw-sbp2.o
 
-obj-$(CONFIG_FIREWIRE) += fw-core.o
-obj-$(CONFIG_FIREWIRE_OHCI) += fw-ohci.o
-obj-$(CONFIG_FIREWIRE_SBP2) += fw-sbp2.o
+obj-$(CONFIG_FIREWIRE) += firewire-core.o
+obj-$(CONFIG_FIREWIRE_OHCI) += firewire-ohci.o
+obj-$(CONFIG_FIREWIRE_SBP2) += firewire-sbp2.o
Signature · 3 lines
Stefan Richter
-=====-=-=== -=-= ==--=
http://arcgraph.de/sr/
#1 lore raw
Quoted 3 lines · Stefan Richter

Of course everybody immediately associates "fw-" with FireWire, not firmware or firewall or whatever. But "firewire-" has a nice ring to it too.

It's fine with me. I like the less ambiguous names better, and I don't think the length of the names is a problem. If you end up typing the module names too much, you're doing something wrong or working on the firewire stack, in which case you're screwed anyway :)

Kristian