Skip to contentSkip to conversation

Neighbour table overflow

DISCUSSION Sebastiao Antonio Campos (GWA) 2 participants 2 messages Mar 23, 2005

lore
Share & tools
lore
#0 lore raw

After I had applied the solution bellow I got the follwing msg error:

Neighbour table overflow.

Tks

----- Original Message -----
From: "Sebastiao Antonio Campos (GWA)" <[email protected]>
To: "Netfilter list" <[email protected]>; "Sertys" <[email protected]>
Sent: Tuesday, March 22, 2005 9:51 PM
Subject: Re: Two netwok cards to access the internet.

Quoted 26 lines

Thanks.

It is working good.

----- Original Message -----
From: "Sertys" <[email protected]>
To: "Netfilter list" <[email protected]>
Sent: Tuesday, March 22, 2005 7:24 PM
Subject: Re: Two netwok cards to access the internet.

On Tue, 22 Mar 2005 18:54:26 -0300, Sebastião Antônio Campos <[email protected]> wrote:

Well, that's easy. When you know the ports you want to map through the interfaces, just do

iptables -t nat -A POSTROUTING -m multiport -p tcp -s 172.17.1.8 --dports 25,110,1723,1701,47 -o eth0 -j MASQUERADE
iptables -t nat -A POSTROUTING -s 172.17.0.0/16 -o eth2 -j MASQUERADE or even better
iptables -t nat -A POSTROUTING -s 172.17.0.0/16 -o eth2 -j SNAT --to-source $ETH2_IP

Quoted 33 lines

Those are simple states, you might add --syn or -m state, it's a choice of yours anyway.

Quoted 29 lines

Hi!

I have the following:

A RedHat 9.0 with 3 Network cards: One we use in local network (eth1) and the other (eth0 and eth2) to access the internet.

I'd like to separate the traffic. In the eth0 use only with the e-mail server (pop, smtp, 1723, 1701 and protocol 47) and the eht0 with others traffis (http, https, msn....).

I tried

iptables -t nat -A POSTROUTING -o eth2 -s 172.17.1.8 -j MASQUERADE (--this ip addrs is pop and smtp server)
iptables -t nat -A POSTROUTING -o eth0 -s 172.17.0.0/16 -j MASQUERADE

But when I did this I could not access the port 1723, 1701 and protocol 47 using the eth2.

I tried too use only iptables -t nat -A POSTROUTING -o eth2 -s 172.17.0.0/16 -j MASQUERADE

And I got the same prob.

If I use iptables -t nat -A POSTROUTING -s 172.17.0.0/16 -j MASQUERADE

I will get a success access. Only when I use iptables -t nat -A POSTROUTING -s 172.17.0.0/16 -j MASQUERADE (without -o eth2 or -o

eth0).

Quoted 23 lines
Quoted 13 lines

Who could help me?

Thanks

Sebastiгo Antфnio Campos
Infojoi Computadores Ltda
Joinville -SC - R. Iririъ, 3587
Cml. (47) 437-0796 - Cel. (47) 9927-5349
[email protected]
http://www.lupusnet.com.br

Signature · 5 lines
www.supportivo.org

I can't stop myself checking for pigs in the outlets. Everybody thinks i'm
a punk, cause of the hairstyle(220V).
end
#1 lore raw
Quoted 3 lines · Sebastiao Antonio Campos (GWA)

After I had applied the solution bellow I got the follwing msg error:

Neighbour table overflow.

IIRC--that error means you've filled up your arp table. the values (defaults shown) are controlled by the kernel parameters:

        net.ipv4.neigh.default.gc_thresh3 = 1024
        net.ipv4.neigh.default.gc_thresh2 = 512
        net.ipv4.neigh.default.gc_thresh1 = 128

how many hosts are on the physical subnets with your firewall machine?

i was surprised to see you say that everything was working, as your question appeared to be about policy routing, yet setting up a SNAT seemed to magically make it work--which made no sense to me.

-j

--
"Well, I'm not calling you a liar, but... I can't think of a way to
finish that sentence."
--The Simpsons