Neighbour table overflow
After I had applied the solution bellow I got the follwing msg error:
Neighbour table overflow.
Tks
----- Original Message -----
From: "Sebastiao Antonio Campos (GWA)" <[email protected]>
To: "Netfilter list" <[email protected]>; "Sertys" <[email protected]>
Sent: Tuesday, March 22, 2005 9:51 PM
Subject: Re: Two netwok cards to access the internet.
Quoted 26 lines
Thanks.
It is working good.
----- Original Message -----
From: "Sertys" <[email protected]>
To: "Netfilter list" <[email protected]>
Sent: Tuesday, March 22, 2005 7:24 PM
Subject: Re: Two netwok cards to access the internet.On Tue, 22 Mar 2005 18:54:26 -0300, Sebastião Antônio Campos <[email protected]> wrote:
Well, that's easy. When you know the ports you want to map through the interfaces, just do
iptables -t nat -A POSTROUTING -m multiport -p tcp -s 172.17.1.8 --dports 25,110,1723,1701,47 -o eth0 -j MASQUERADE
iptables -t nat -A POSTROUTING -s 172.17.0.0/16 -o eth2 -j MASQUERADE or even better
iptables -t nat -A POSTROUTING -s 172.17.0.0/16 -o eth2 -j SNAT --to-source $ETH2_IP
Quoted 33 lines
Those are simple states, you might add --syn or -m state, it's a choice of yours anyway.
Quoted 29 lines
Hi!
I have the following:
A RedHat 9.0 with 3 Network cards: One we use in local network (eth1) and the other (eth0 and eth2) to access the internet.
I'd like to separate the traffic. In the eth0 use only with the e-mail server (pop, smtp, 1723, 1701 and protocol 47) and the eht0 with others traffis (http, https, msn....).
I tried
iptables -t nat -A POSTROUTING -o eth2 -s 172.17.1.8 -j MASQUERADE (--this ip addrs is pop and smtp server)
iptables -t nat -A POSTROUTING -o eth0 -s 172.17.0.0/16 -j MASQUERADEBut when I did this I could not access the port 1723, 1701 and protocol 47 using the eth2.
I tried too use only iptables -t nat -A POSTROUTING -o eth2 -s 172.17.0.0/16 -j MASQUERADE
And I got the same prob.
If I use iptables -t nat -A POSTROUTING -s 172.17.0.0/16 -j MASQUERADE
I will get a success access. Only when I use iptables -t nat -A POSTROUTING -s 172.17.0.0/16 -j MASQUERADE (without -o eth2 or -o
eth0).
Quoted 23 lines
Quoted 13 lines
Who could help me?
Thanks
Sebastiгo Antфnio Campos
Infojoi Computadores Ltda
Joinville -SC - R. Iririъ, 3587
Cml. (47) 437-0796 - Cel. (47) 9927-5349
[email protected]
http://www.lupusnet.com.brSignature · 5 lines
www.supportivo.org I can't stop myself checking for pigs in the outlets. Everybody thinks i'm a punk, cause of the hairstyle(220V). end
Quoted 3 lines · Sebastiao Antonio Campos (GWA)
After I had applied the solution bellow I got the follwing msg error:
Neighbour table overflow.
IIRC--that error means you've filled up your arp table. the values (defaults shown) are controlled by the kernel parameters:
net.ipv4.neigh.default.gc_thresh3 = 1024
net.ipv4.neigh.default.gc_thresh2 = 512
net.ipv4.neigh.default.gc_thresh1 = 128how many hosts are on the physical subnets with your firewall machine?
i was surprised to see you say that everything was working, as your question appeared to be about policy routing, yet setting up a SNAT seemed to magically make it work--which made no sense to me.
-j
--
"Well, I'm not calling you a liar, but... I can't think of a way to
finish that sentence."
--The Simpsons