ERROR -157 reading data
Hi all,
I have created my vg00 (/dev/hdb2) with 1 LV (lv00).
After mounting it, I can work fine with lv00.
But, on next boot, vgscan removes /etc/lvmtab and /etc/lvmtab.d and it isn't able to create a new set of these files. <SNIP>
vgscan -- reading data of volume group "vg00" from physical volume(s)
vgscan -- ERROR -157: can't get data of volume group "vg00" from physical volume(s)
vgscan -- ERROR -157: creating "/etc/lvmtab" and "/etc/lvmtab.d"
With others LVM tools also give almost same msgs :
vgcfgbackup -- reading volume group data for "vg00" from disk(s)I vgcfgbackup -- ERROR -157: reading VGDA of "vg00" vgcfgbackup -- ERROR -313: backing up volume group "vg00"
vgck -- reading volume group data for "vg00" from physical volume(s) vgck -- ERROR -157: reading data of volume group "vg00" from physical volume(s) vgck -- please DON'T run vgscan prior to vgcfgrestore
My disk is a IDE 3.2GB with 2 partitions :
# fdisk -l /dev/hdb
Disk /dev/hdb: 128 heads, 63 sectors, 785 cylinders Units = cylinders of 8064 * 512 bytes
Device Boot Start End Blocks Id System/dev/hdb1 1 5 20128+ 83 Linux native/dev/hdb2 6 785 3144960 83 Unknown
The LVM program is built into my kernel (2.0.36) not as a module. Am I missing something in my configuration?
Please help me!
Thanks in advance,
Fernando Dammous
Hi Fernando,
looks like something has overwritten parts of the VGDA (metadata aka Volume Group Descriptor Area) on /dev/hdb2.
Quoted 12 lines
Hi all,
I have created my vg00 (
/dev/hdb2) with 1 LV (lv00).=20 After mounting it, I can work fine with lv00.=20
But, on next boot, vgscan removes/etc/lvmtaband/etc/lvmtab.dand it = isn't able to create a new set of these files.
<SNIP>
vgscan -- reading data of volume group "vg00" from physical volume(s) vgscan -- ERROR -157: can't get data of volume group "vg00" from = physical volume(s)
vgscan -- ERROR -157: creating "/etc/lvmtab" and "/etc/lvmtab.d"
This error indicates, that the number of logical volumes differs between the VG part and the LV part(s) of the VGDA.
Quoted 11 lines
With others LVM tools also give almost same msgs :
vgcfgbackup -- reading volume group data for "vg00" from disk(s)I=20 vgcfgbackup -- ERROR -157: reading VGDA of "vg00" vgcfgbackup -- ERROR -313: backing up volume group "vg00"
vgck -- reading volume group data for "vg00" from physical volume(s) vgck -- ERROR -157: reading data of volume group "vg00" from physical = volume(s)
vgck -- please DON'T run vgscan prior to vgcfgrestore
Please have a look at FAQ question 8.
Do you have an actual backup in /etc/lvmconf ?.
Please look with "ls -lt /etc/lvmconf/vg00*" for a recent backup.
If yes you are a lucky man 8*)
Say you have /etc/lvmconf/vg00.conf then restore it with "vgfgrestore -f /etc/lvmconf/vg00.conf -n vg00 /dev/hdb2" and retry "vgscan;vgchange -ay"
Quoted 4 lines
My disk is a IDE 3.2GB with 2 partitions :
# fdisk -l /dev/hdb
Quoted 8 lines
Disk
/dev/hdb: 128 heads, 63 sectors, 785 cylinders Units =3D cylinders of 8064 * 512 bytesDevice Boot Start End Blocks Id System
/dev/hdb11 5 20128+ 83 =
Linux native/dev/hdb26 785 3144960 83 =
Unknown
You mean partition Id fe, do you?
Quoted 4 lines
The LVM program is built into my kernel (2.0.36) not as a module. Am I missing something in my configuration?
O.k.
Quoted 6 lines
Please help me!
Thanks in advance,
Fernando Dammous
Regards,
Heinz
--
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Systemmanagement CS-TS T-Nova
Entwicklungszentrum Darmstadt
Heinz Mauelshagen Otto-Roehm-Strasse 71c
Senior Systems Engineer Postfach 10 05 41
64205 Darmstadt [email protected] Germany +49 6151 886-425 FAX-386
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-