Skip to contentSkip to conversation

raspberry Pi core-image-sato

DISCUSSION Edward Vidal 3 participants 3 messages Jul 23, 2015

lore
Share & tools
lore
#0 lore raw

Hi Gary,Is this the log that you need?I also ran the  bitbake -DD core-image-sato and have the log for that run.

| WARNING: exit code 1 from a shell command.
| ERROR: oe_runconf failed
| ERROR: Function failed: do_configure (log file is located at /home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/work/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/libepoxy/1.2+gitAUTOINC+20062c25e7-r0/temp/log.do_configure.9672)

ERROR: Task 4597 (/home/vidal/wkg/yocto/RaspberryPi2/poky/meta/recipes-graphics/libepoxy/libepoxy_git.bb, do_configure) failed with exit code '1' Let me know what I can provide.Thanks for the help Regards,Edward Vidal Jr.
e-mail [email protected]
915-595-1613

#1 lore raw
Quoted 9 lines · Edward Vidal

Hi Gary,
Is this the log that you need?
I also ran the bitbake -DD core-image-sato and have the log for that run.

| WARNING: exit code 1 from a shell command.
| ERROR: oe_runconf failed
| ERROR: Function failed: do_configure (log file is located at

/home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/work/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/libepoxy/1.2+gitAUTOINC+20062c25e7-r0/temp/log.do_configure.9672)
ERROR: Task 4597 (/home/vidal/wkg/yocto/RaspberryPi2/poky/meta/recipes-graphics/libepoxy/libepoxy_git.bb, do_configure) failed with exit code '1'

Did you look at the error? It's the same as you had yesterday:
checking for EGL... no
configure: error: Package requirements (egl) were not met:
No package 'egl' found

Did you perhaps remove those PREFERRED_PROVIDER lines from local.conf? You need these lines for this to work:
PREFERRED_PROVIDER_virtual/egl ?= "vc-graphics-hardfp" PREFERRED_PROVIDER_virtual/libgles2 ?= "vc-graphics-hardfp"

Quoted 1 line

Let me know what I can provide.

Send your _complete_ local.conf and bblayers.conf

Signature · 4 lines
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------
#2 lore raw

Re: ***SPAM*** raspberry Pi core-image-sato

In reply to Edward Vidal

Hi,

Not sure if it’s the case, because the config.log might give more details, but maybe you can try adding the following to your recipe :

EXTRA_OECONF += “-I${STAGING_DIR_TARGET}/usr/include/interface/vcos/pthreads/ \

                                      -I${STAGING_DIR_TARGET}/usr/include/interface/vmcs_host/linux/"

I needed that to compile other packages that were using EGL.

Once again, just a hint, no warranty whatsoever…

BR,

Hervé

From: [email protected] [mailto:[email protected]] On Behalf Of Edward Vidal
Sent: jeudi 23 juillet 2015 16:38
To: [email protected]
Subject: ***SPAM*** [yocto] raspberry Pi core-image-sato

Hi Gary,

Is this the log that you need?

I also ran the bitbake -DD core-image-sato and have the log for that run.

| WARNING: exit code 1 from a shell command.
| ERROR: oe_runconf failed
| ERROR: Function failed: do_configure (log file is located at /home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/work/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/libepoxy/1.2+gitAUTOINC+20062c25e7-r0/temp/log.do_configure.9672)

ERROR: Task 4597 (/home/vidal/wkg/yocto/RaspberryPi2/poky/meta/recipes-graphics/libepoxy/libepoxy_git.bb, do_configure) failed with exit code '1'

Let me know what I can provide.

Thanks for the help

Regards,

Edward Vidal Jr.
e-mail [email protected] <mailto:[email protected]> 915-595-1613