raspberry Pi core-image-sato
Hi Gary,Is this the log that you need?I also ran the bitbake -DD core-image-sato and have the log for that run.
| WARNING: exit code 1 from a shell command. | ERROR: oe_runconf failed | ERROR: Function failed: do_configure (log file is located at /home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/work/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/libepoxy/1.2+gitAUTOINC+20062c25e7-r0/temp/log.do_configure.9672)
ERROR: Task 4597 (/home/vidal/wkg/yocto/RaspberryPi2/poky/meta/recipes-graphics/libepoxy/libepoxy_git.bb, do_configure) failed with exit code '1' Let me know what I can provide.Thanks for the help Regards,Edward Vidal Jr.
e-mail [email protected]
915-595-1613
Quoted 9 lines · Edward Vidal
Hi Gary,
Is this the log that you need?
I also ran the bitbake -DD core-image-sato and have the log for that run.| WARNING: exit code 1 from a shell command. | ERROR: oe_runconf failed | ERROR: Function failed: do_configure (log file is located at
/home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/work/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/libepoxy/1.2+gitAUTOINC+20062c25e7-r0/temp/log.do_configure.9672)
ERROR: Task 4597 (/home/vidal/wkg/yocto/RaspberryPi2/poky/meta/recipes-graphics/libepoxy/libepoxy_git.bb,do_configure) failed with exit code '1'
Did you look at the error? It's the same as you had yesterday:
checking for EGL... no
configure: error: Package requirements (egl) were not met:
No package 'egl' found
Did you perhaps remove those PREFERRED_PROVIDER lines from local.conf? You need these lines for this to work:
PREFERRED_PROVIDER_virtual/egl ?= "vc-graphics-hardfp" PREFERRED_PROVIDER_virtual/libgles2 ?= "vc-graphics-hardfp"
Quoted 1 line
Let me know what I can provide.
Send your _complete_ local.conf and bblayers.conf
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------
Re: ***SPAM*** raspberry Pi core-image-sato
In reply to Edward VidalHi,
Not sure if it’s the case, because the config.log might give more details, but maybe you can try adding the following to your recipe :
EXTRA_OECONF += “-I${STAGING_DIR_TARGET}/usr/include/interface/vcos/pthreads/ \
-I${STAGING_DIR_TARGET}/usr/include/interface/vmcs_host/linux/"I needed that to compile other packages that were using EGL.
Once again, just a hint, no warranty whatsoever…
BR,
Hervé
From: [email protected] [mailto:[email protected]] On Behalf Of Edward Vidal
Sent: jeudi 23 juillet 2015 16:38
To: [email protected]
Subject: ***SPAM*** [yocto] raspberry Pi core-image-sato
Hi Gary,
Is this the log that you need?
I also ran the bitbake -DD core-image-sato and have the log for that run.
| WARNING: exit code 1 from a shell command. | ERROR: oe_runconf failed | ERROR: Function failed: do_configure (log file is located at /home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/work/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/libepoxy/1.2+gitAUTOINC+20062c25e7-r0/temp/log.do_configure.9672)
ERROR: Task 4597 (/home/vidal/wkg/yocto/RaspberryPi2/poky/meta/recipes-graphics/libepoxy/libepoxy_git.bb, do_configure) failed with exit code '1'
Let me know what I can provide.
Thanks for the help
Regards,
Edward Vidal Jr.
e-mail [email protected] <mailto:[email protected]> 915-595-1613