Skip to contentSkip to conversation

hello

DISCUSSION Dhaval Patel 2 participants 3 messages May 23, 2003 1 message not in the archive MD RAID

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): 000f01c32101$80b90980$1c640abe@nigel

#1 lore raw

Sorry, I should have provided this information in the first email. I am using RAID 5 and I downloaded the latest firmware. I think I found the problem though. Currently the box is in my bedroom since I am testing it before I put it in its permanent location. And since I actually want to get some sleep at night I turn the box off. Well I realized that it just so happens that it shuts down the raid card at the very end. If you turn it off too quickly the raid card cannot shutdown cleanly and the array is degraded. I wasnt checking the array and assuming that everything was fine. There are no errors reported in messages or syslog. I ran the CLI from 3ware and saw that the array is in fact degraded. I rebuilt it and ran the tests again and everything seems fine. Here is the information about the controller from the CLI

Driver:   1.02.00.033
Model:    7500-4
FW:       FE7X 1.05.00.049
BIOS:     BE7X 1.08.00.046
Monitor:  ME7X 1.01.00.035
PCB:      Rev3
PCHIP:    V1.30
ACHIP:    V3.20

I am actually running Slackware so I downloaded the driver for suse or redhat kernel I dont remember which, and compiled it with the vanilla kernel that I download when I install any box.

I did install the 3dm and launched it with 3dmd. But I cannot get to the web interface. How can I do that. Does it offer the same features that the CLI offers?

Thanks,
Dhaval

Quoted 55 lines · Nick

Hi Dhaval,
Did you download the source code for the driver and build it your self? What RAID level are you using?
and what revision of firmware did you download. One common problem that causes this type of failure is a loose connection to one of your drives, either the parallel cable or the power cable, if can recheck these first it might help.
Are you using 3DM, the web based management tool for 3Ware controllers, this will give you very detailed information on what is happening with your array.

Kind Regards,

Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045

----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Thursday, May 22, 2003 6:26 PM
Subject: hello

Quoted 1 line

Hi, everyone. I am new to this list. Currently I am trying to get IDE raid

working with

Quoted 1 line

the 3ware 7500-4 controller, using Western Digital 120GB drives. I am

using Slackware

Quoted 1 line

with 2.4.20 kernel. I have the OS installed and am using the latest driver

(1.02.00.033)

Quoted 1 line

that you can download from 3ware's website. I also applied the latest

firmware that came

Quoted 1 line

along with the driver. The bootup is fine, its just that when I try to

move huge files

Quoted 1 line

that the box freezes. Yesterday I was copying 50 550+MB files from one

directory to

Quoted 1 line

another and everything went well. This morning I am copying the same files

to another

Quoted 1 line

directory and it froze on the second file. After it freezes I can

sometimes ping it and

Quoted 1 line

sometimes I cannot. I havent seen anything in /var/log/messages. After a

restart

Quoted 9 lines

everything seems fine.

Thanks in advanced for your help,
Dhaval
-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#2 lore raw

Hi Dhaval,
Yes, the shutdowns when using 3Ware controllers can take some time, particularly when you have been dealing with large files, doing unclean shutdown will indeed put the array in to a degraded state.

The 3DM web based manager has all the functionality of the CLI and is much easier on the eye, to use it point your browser to http://localhost:1080 You will also find access to the controller logs and alarms from here, much nicer that the CLI.

Hope this helped.
Kind Regards,

Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045

----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Friday, May 23, 2003 12:00 PM
Subject: Re: hello

Quoted 1 line

Sorry, I should have provided this information in the first email. I am

using RAID 5 and

Quoted 1 line

I downloaded the latest firmware. I think I found the problem though.

Currently the box

Quoted 1 line

is in my bedroom since I am testing it before I put it in its permanent

location. And

Quoted 1 line

since I actually want to get some sleep at night I turn the box off. Well

I realized

Quoted 1 line

that it just so happens that it shuts down the raid card at the very end.

If you turn it

Quoted 1 line

off too quickly the raid card cannot shutdown cleanly and the array is

degraded. I wasnt

Quoted 1 line

checking the array and assuming that everything was fine. There are no

errors reported

Quoted 1 line

in messages or syslog. I ran the CLI from 3ware and saw that the array is

in fact

Quoted 1 line

degraded. I rebuilt it and ran the tests again and everything seems fine.

Here is the

Quoted 11 lines

information about the controller from the CLI

Driver:   1.02.00.033
Model:    7500-4
FW:       FE7X 1.05.00.049
BIOS:     BE7X 1.08.00.046
Monitor:  ME7X 1.01.00.035
PCB:      Rev3
PCHIP:    V1.30
ACHIP:    V3.20
Quoted 1 line

I am actually running Slackware so I downloaded the driver for suse or

redhat kernel I

Quoted 1 line

dont remember which, and compiled it with the vanilla kernel that I

download when I

Quoted 3 lines

install any box.

I did install the 3dm and launched it with 3dmd. But I cannot get to the

web interface.

Quoted 9 lines

How can I do that. Does it offer the same features that the CLI offers?

Thanks,
Dhaval

Quoted 2 lines · Nick

Hi Dhaval,
Did you download the source code for the driver and build it your self?

What

Quoted 4 lines
Quoted 4 lines

RAID level are you using?
and what revision of firmware did you download. One common problem that causes this type of failure is a loose connection to one of your drives, either the parallel cable or the power cable, if can recheck these first

it

Quoted 2 lines
Quoted 2 lines

might help.
Are you using 3DM, the web based management tool for 3Ware controllers,

this

Quoted 12 lines
Quoted 12 lines

will give you very detailed information on what is happening with your array.

Kind Regards,

Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045

Quoted 8 lines
Quoted 8 lines

----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Thursday, May 22, 2003 6:26 PM
Subject: hello

Quoted 1 line

Hi, everyone. I am new to this list. Currently I am trying to get IDE

raid

Quoted 4 lines
Quoted 4 lines

working with

Quoted 1 line

the 3ware 7500-4 controller, using Western Digital 120GB drives. I am

using Slackware

Quoted 1 line

with 2.4.20 kernel. I have the OS installed and am using the latest

driver

Quoted 8 lines
Quoted 8 lines

(1.02.00.033)

Quoted 1 line

that you can download from 3ware's website. I also applied the latest

firmware that came

Quoted 1 line

along with the driver. The bootup is fine, its just that when I try to

move huge files

Quoted 1 line

that the box freezes. Yesterday I was copying 50 550+MB files from one

directory to

Quoted 1 line

another and everything went well. This morning I am copying the same

files

Quoted 4 lines
Quoted 4 lines

to another

Quoted 1 line

directory and it froze on the second file. After it freezes I can

sometimes ping it and

Quoted 1 line

sometimes I cannot. I havent seen anything in /var/log/messages. After

a

Quoted 7 lines
Quoted 7 lines

restart

Quoted 6 lines

everything seems fine.

Thanks in advanced for your help,
Dhaval
-
To unsubscribe from this list: send the line "unsubscribe linux-raid"

in

Quoted 16 lines
Quoted 4 lines
Quoted 3 lines

the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

--

-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#3 lore raw

Hmm, I have been doing some testing and this morning I turned on the box, went to the CLI and made sure that the array was fine, but it still crashed when trying to copy a bunch of files. The only thing I can see happening is that either the controller card isnt shutdown properly, or its not initialized properly.

To get it to work, I have to go into the 3ware config during startup, get it to start rebuilding the array, and move things after the array has been built. Otherwise, it crashes. Does anyone have suggestions how I can go about figuring this out?

Thanks,
Dhaval

Quoted 152 lines

Hi Dhaval,
Yes, the shutdowns when using 3Ware controllers can take some time, particularly when you have been dealing with large files, doing unclean shutdown will indeed put the array in to a degraded state.

The 3DM web based manager has all the functionality of the CLI and is much easier on the eye, to use it point your browser to http://localhost:1080 You will also find access to the controller logs and alarms from here, much nicer that the CLI.

Hope this helped.
Kind Regards,

Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045

----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Friday, May 23, 2003 12:00 PM
Subject: Re: hello

Quoted 1 line

Sorry, I should have provided this information in the first email. I am

using RAID 5 and

Quoted 1 line

I downloaded the latest firmware. I think I found the problem though.

Currently the box

Quoted 1 line

is in my bedroom since I am testing it before I put it in its permanent

location. And

Quoted 1 line

since I actually want to get some sleep at night I turn the box off. Well

I realized

Quoted 1 line

that it just so happens that it shuts down the raid card at the very end.

If you turn it

Quoted 1 line

off too quickly the raid card cannot shutdown cleanly and the array is

degraded. I wasnt

Quoted 1 line

checking the array and assuming that everything was fine. There are no

errors reported

Quoted 1 line

in messages or syslog. I ran the CLI from 3ware and saw that the array is

in fact

Quoted 1 line

degraded. I rebuilt it and ran the tests again and everything seems fine.

Here is the

Quoted 11 lines

information about the controller from the CLI

Driver:   1.02.00.033
Model:    7500-4
FW:       FE7X 1.05.00.049
BIOS:     BE7X 1.08.00.046
Monitor:  ME7X 1.01.00.035
PCB:      Rev3
PCHIP:    V1.30
ACHIP:    V3.20
Quoted 1 line

I am actually running Slackware so I downloaded the driver for suse or

redhat kernel I

Quoted 1 line

dont remember which, and compiled it with the vanilla kernel that I

download when I

Quoted 3 lines

install any box.

I did install the 3dm and launched it with 3dmd. But I cannot get to the

web interface.

Quoted 9 lines

How can I do that. Does it offer the same features that the CLI offers?

Thanks,
Dhaval

Quoted 2 lines · Nick

Hi Dhaval,
Did you download the source code for the driver and build it your self?

What

Quoted 4 lines
Quoted 4 lines

RAID level are you using?
and what revision of firmware did you download. One common problem that causes this type of failure is a loose connection to one of your drives, either the parallel cable or the power cable, if can recheck these first

it

Quoted 2 lines
Quoted 2 lines

might help.
Are you using 3DM, the web based management tool for 3Ware controllers,

this

Quoted 12 lines
Quoted 12 lines

will give you very detailed information on what is happening with your array.

Kind Regards,

Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045

Quoted 8 lines
Quoted 8 lines

----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Thursday, May 22, 2003 6:26 PM
Subject: hello

Quoted 1 line

Hi, everyone. I am new to this list. Currently I am trying to get IDE

raid

Quoted 4 lines
Quoted 4 lines

working with

Quoted 1 line

the 3ware 7500-4 controller, using Western Digital 120GB drives. I am

using Slackware

Quoted 1 line

with 2.4.20 kernel. I have the OS installed and am using the latest

driver

Quoted 8 lines
Quoted 8 lines

(1.02.00.033)

Quoted 1 line

that you can download from 3ware's website. I also applied the latest

firmware that came

Quoted 1 line

along with the driver. The bootup is fine, its just that when I try to

move huge files

Quoted 1 line

that the box freezes. Yesterday I was copying 50 550+MB files from one

directory to

Quoted 1 line

another and everything went well. This morning I am copying the same

files

Quoted 4 lines
Quoted 4 lines

to another

Quoted 1 line

directory and it froze on the second file. After it freezes I can

sometimes ping it and

Quoted 1 line

sometimes I cannot. I havent seen anything in /var/log/messages. After

a

Quoted 7 lines
Quoted 7 lines

restart

Quoted 6 lines

everything seems fine.

Thanks in advanced for your help,
Dhaval
-
To unsubscribe from this list: send the line "unsubscribe linux-raid"

in

Quoted 7 lines
Quoted 4 lines
Quoted 3 lines

the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Quoted 9 lines

--

-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html