hello
Sorry, I should have provided this information in the first email. I am using RAID 5 and I downloaded the latest firmware. I think I found the problem though. Currently the box is in my bedroom since I am testing it before I put it in its permanent location. And since I actually want to get some sleep at night I turn the box off. Well I realized that it just so happens that it shuts down the raid card at the very end. If you turn it off too quickly the raid card cannot shutdown cleanly and the array is degraded. I wasnt checking the array and assuming that everything was fine. There are no errors reported in messages or syslog. I ran the CLI from 3ware and saw that the array is in fact degraded. I rebuilt it and ran the tests again and everything seems fine. Here is the information about the controller from the CLI
Driver: 1.02.00.033 Model: 7500-4 FW: FE7X 1.05.00.049 BIOS: BE7X 1.08.00.046 Monitor: ME7X 1.01.00.035 PCB: Rev3 PCHIP: V1.30 ACHIP: V3.20
I am actually running Slackware so I downloaded the driver for suse or redhat kernel I dont remember which, and compiled it with the vanilla kernel that I download when I install any box.
I did install the 3dm and launched it with 3dmd. But I cannot get to the web interface. How can I do that. Does it offer the same features that the CLI offers?
Thanks,
Dhaval
Quoted 55 lines · Nick
Hi Dhaval,
Did you download the source code for the driver and build it your self? What RAID level are you using?
and what revision of firmware did you download. One common problem that causes this type of failure is a loose connection to one of your drives, either the parallel cable or the power cable, if can recheck these first it might help.
Are you using 3DM, the web based management tool for 3Ware controllers, this will give you very detailed information on what is happening with your array.Kind Regards,
Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Thursday, May 22, 2003 6:26 PM
Subject: helloQuoted 1 line
Hi, everyone. I am new to this list. Currently I am trying to get IDE raid
working with
Quoted 1 line
the 3ware 7500-4 controller, using Western Digital 120GB drives. I am
using Slackware
Quoted 1 line
with 2.4.20 kernel. I have the OS installed and am using the latest driver
(1.02.00.033)
Quoted 1 line
that you can download from 3ware's website. I also applied the latest
firmware that came
Quoted 1 line
along with the driver. The bootup is fine, its just that when I try to
move huge files
Quoted 1 line
that the box freezes. Yesterday I was copying 50 550+MB files from one
directory to
Quoted 1 line
another and everything went well. This morning I am copying the same files
to another
Quoted 1 line
directory and it froze on the second file. After it freezes I can
sometimes ping it and
Quoted 1 line
sometimes I cannot. I havent seen anything in
/var/log/messages. After arestart
Quoted 9 lines
everything seems fine.
Thanks in advanced for your help,
Dhaval
-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Dhaval,
Yes, the shutdowns when using 3Ware controllers can take some time, particularly when you have been dealing with large files, doing unclean shutdown will indeed put the array in to a degraded state.
The 3DM web based manager has all the functionality of the CLI and is much easier on the eye, to use it point your browser to http://localhost:1080 You will also find access to the controller logs and alarms from here, much nicer that the CLI.
Hope this helped.
Kind Regards,
Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045
----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Friday, May 23, 2003 12:00 PM
Subject: Re: hello
Quoted 1 line
Sorry, I should have provided this information in the first email. I am
using RAID 5 and
Quoted 1 line
I downloaded the latest firmware. I think I found the problem though.
Currently the box
Quoted 1 line
is in my bedroom since I am testing it before I put it in its permanent
location. And
Quoted 1 line
since I actually want to get some sleep at night I turn the box off. Well
I realized
Quoted 1 line
that it just so happens that it shuts down the raid card at the very end.
If you turn it
Quoted 1 line
off too quickly the raid card cannot shutdown cleanly and the array is
degraded. I wasnt
Quoted 1 line
checking the array and assuming that everything was fine. There are no
errors reported
Quoted 1 line
in messages or syslog. I ran the CLI from 3ware and saw that the array is
in fact
Quoted 1 line
degraded. I rebuilt it and ran the tests again and everything seems fine.
Here is the
Quoted 11 lines
information about the controller from the CLI
Driver: 1.02.00.033 Model: 7500-4 FW: FE7X 1.05.00.049 BIOS: BE7X 1.08.00.046 Monitor: ME7X 1.01.00.035 PCB: Rev3 PCHIP: V1.30 ACHIP: V3.20
Quoted 1 line
I am actually running Slackware so I downloaded the driver for suse or
redhat kernel I
Quoted 1 line
dont remember which, and compiled it with the vanilla kernel that I
download when I
Quoted 3 lines
install any box.
I did install the 3dm and launched it with 3dmd. But I cannot get to the
web interface.
Quoted 9 lines
How can I do that. Does it offer the same features that the CLI offers?
Thanks,
DhavalQuoted 2 lines · Nick
Hi Dhaval,
Did you download the source code for the driver and build it your self?
What
Quoted 4 lines
Quoted 4 lines
RAID level are you using?
and what revision of firmware did you download. One common problem that causes this type of failure is a loose connection to one of your drives, either the parallel cable or the power cable, if can recheck these first
it
Quoted 2 lines
Quoted 2 lines
might help.
Are you using 3DM, the web based management tool for 3Ware controllers,
this
Quoted 12 lines
Quoted 12 lines
will give you very detailed information on what is happening with your array.
Kind Regards,
Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045
Quoted 8 lines
Quoted 8 lines
----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Thursday, May 22, 2003 6:26 PM
Subject: helloQuoted 1 line
Hi, everyone. I am new to this list. Currently I am trying to get IDE
raid
Quoted 4 lines
Quoted 4 lines
working with
Quoted 1 line
the 3ware 7500-4 controller, using Western Digital 120GB drives. I am
using Slackware
Quoted 1 line
with 2.4.20 kernel. I have the OS installed and am using the latest
driver
Quoted 8 lines
Quoted 8 lines
(1.02.00.033)
Quoted 1 line
that you can download from 3ware's website. I also applied the latest
firmware that came
Quoted 1 line
along with the driver. The bootup is fine, its just that when I try to
move huge files
Quoted 1 line
that the box freezes. Yesterday I was copying 50 550+MB files from one
directory to
Quoted 1 line
another and everything went well. This morning I am copying the same
files
Quoted 4 lines
Quoted 4 lines
to another
Quoted 1 line
directory and it froze on the second file. After it freezes I can
sometimes ping it and
Quoted 1 line
sometimes I cannot. I havent seen anything in
/var/log/messages. After
a
Quoted 7 lines
Quoted 7 lines
restart
Quoted 6 lines
everything seems fine.
Thanks in advanced for your help,
Dhaval
-
To unsubscribe from this list: send the line "unsubscribe linux-raid"
in
Quoted 16 lines
Quoted 4 lines
Quoted 3 lines
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html--
-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Hmm, I have been doing some testing and this morning I turned on the box, went to the CLI and made sure that the array was fine, but it still crashed when trying to copy a bunch of files. The only thing I can see happening is that either the controller card isnt shutdown properly, or its not initialized properly.
To get it to work, I have to go into the 3ware config during startup, get it to start rebuilding the array, and move things after the array has been built. Otherwise, it crashes. Does anyone have suggestions how I can go about figuring this out?
Thanks,
Dhaval
Quoted 152 lines
Hi Dhaval,
Yes, the shutdowns when using 3Ware controllers can take some time, particularly when you have been dealing with large files, doing unclean shutdown will indeed put the array in to a degraded state.The 3DM web based manager has all the functionality of the CLI and is much easier on the eye, to use it point your browser to http://localhost:1080 You will also find access to the controller logs and alarms from here, much nicer that the CLI.
Hope this helped.
Kind Regards,Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Friday, May 23, 2003 12:00 PM
Subject: Re: helloQuoted 1 line
Sorry, I should have provided this information in the first email. I am
using RAID 5 and
Quoted 1 line
I downloaded the latest firmware. I think I found the problem though.
Currently the box
Quoted 1 line
is in my bedroom since I am testing it before I put it in its permanent
location. And
Quoted 1 line
since I actually want to get some sleep at night I turn the box off. Well
I realized
Quoted 1 line
that it just so happens that it shuts down the raid card at the very end.
If you turn it
Quoted 1 line
off too quickly the raid card cannot shutdown cleanly and the array is
degraded. I wasnt
Quoted 1 line
checking the array and assuming that everything was fine. There are no
errors reported
Quoted 1 line
in messages or syslog. I ran the CLI from 3ware and saw that the array is
in fact
Quoted 1 line
degraded. I rebuilt it and ran the tests again and everything seems fine.
Here is the
Quoted 11 lines
information about the controller from the CLI
Driver: 1.02.00.033 Model: 7500-4 FW: FE7X 1.05.00.049 BIOS: BE7X 1.08.00.046 Monitor: ME7X 1.01.00.035 PCB: Rev3 PCHIP: V1.30 ACHIP: V3.20Quoted 1 line
I am actually running Slackware so I downloaded the driver for suse or
redhat kernel I
Quoted 1 line
dont remember which, and compiled it with the vanilla kernel that I
download when I
Quoted 3 lines
install any box.
I did install the 3dm and launched it with 3dmd. But I cannot get to the
web interface.
Quoted 9 lines
How can I do that. Does it offer the same features that the CLI offers?
Thanks,
DhavalQuoted 2 lines · Nick
Hi Dhaval,
Did you download the source code for the driver and build it your self?What
Quoted 4 lines
Quoted 4 lines
RAID level are you using?
and what revision of firmware did you download. One common problem that causes this type of failure is a loose connection to one of your drives, either the parallel cable or the power cable, if can recheck these firstit
Quoted 2 lines
Quoted 2 lines
might help.
Are you using 3DM, the web based management tool for 3Ware controllers,this
Quoted 12 lines
Quoted 12 lines
will give you very detailed information on what is happening with your array.
Kind Regards,
Nick Gleeson
3Ware Applications Engineer
Technical Support (Europe)
[email protected]
www.3ware.com
Phone +353 61 702045Quoted 8 lines
Quoted 8 lines
----- Original Message -----
From: Dhaval Patel <[email protected]>
To: <[email protected]>
Sent: Thursday, May 22, 2003 6:26 PM
Subject: helloQuoted 1 line
Hi, everyone. I am new to this list. Currently I am trying to get IDE
raid
Quoted 4 lines
Quoted 4 lines
working with
Quoted 1 line
the 3ware 7500-4 controller, using Western Digital 120GB drives. I am
using Slackware
Quoted 1 line
with 2.4.20 kernel. I have the OS installed and am using the latest
driver
Quoted 8 lines
Quoted 8 lines
(1.02.00.033)
Quoted 1 line
that you can download from 3ware's website. I also applied the latest
firmware that came
Quoted 1 line
along with the driver. The bootup is fine, its just that when I try to
move huge files
Quoted 1 line
that the box freezes. Yesterday I was copying 50 550+MB files from one
directory to
Quoted 1 line
another and everything went well. This morning I am copying the same
files
Quoted 4 lines
Quoted 4 lines
to another
Quoted 1 line
directory and it froze on the second file. After it freezes I can
sometimes ping it and
Quoted 1 line
sometimes I cannot. I havent seen anything in
/var/log/messages. Aftera
Quoted 7 lines
Quoted 7 lines
restart
Quoted 6 lines
everything seems fine.
Thanks in advanced for your help,
Dhaval
-
To unsubscribe from this list: send the line "unsubscribe linux-raid"in
Quoted 7 lines
Quoted 4 lines
Quoted 3 lines
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.htmlQuoted 9 lines
--
-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html