Skip to contentSkip to conversation

clk-imx8mm: Reduce SPL binary size

PATCH In review Fabio Estevam 4 participants 14 messages Sep 26, 2022 – Oct 21, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover clk-imx8mm: Reduce SPL binary size

Reduce the SPL binary size by building some clocks only for the non-SPL case, such as Ethernet and PWM and by also building ECSPI and QSPI when their respective drivers are enabled.

On a imx8mm_evk_defconfig the following SPL binary reduction was observed.

Prior to this series:

$ aarch64-linux-gnu-readelf -s spl/u-boot-spl | sort -nk 3 | grep imx8mm_clk_probe
   766: 00000000007f34c8  4100 FUNC    LOCAL  DEFAULT    1 imx8mm_clk_probe

After this series:

$ aarch64-linux-gnu-readelf -s spl/u-boot-spl | sort -nk 3 | grep imx8mm_clk_probe
   766: 00000000007f34c8  3316 FUNC    LOCAL  DEFAULT    1 imx8mm_clk_probe

Total reduction: 4100 - 3316 = 784 bytes.

Fabio Estevam (4):
clk-imx8mm: Only build PWM clocks in non-SPL code
clk-imx8mm: Move CLK_ENET_AXI to the non-SPL section
clk-imx8mm: Only build ecspi clocks when CONFIG_DM_SPI=y
clk-imx8mm: Only build QSPI clocks when CONFIG_NXP_FSPI=y

 drivers/clk/imx/clk-imx8mm.c | 86 ++++++++++++++++++++----------------
 1 file changed, 49 insertions(+), 37 deletions(-)
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/4 clk-imx8mm: Only build PWM clocks in non-SPL code

PWM is not used inside SPL, so do not define the PWM clocks inside SPL to reduce the final SPL binary size.

---
 drivers/clk/imx/clk-imx8mm.c | 34 ++++++++++++++++++----------------
 1 file changed, 18 insertions(+), 16 deletions(-)
drivers/clk/imx/clk-imx8mm.c +18 -16
index 542aa31f7a..0d7891f11a 100644
@@ -66,6 +66,7 @@ static const char *imx8mm_i2c3_sels[] = {"clock-osc-24m", "sys_pll1_160m", "sys_
 static const char *imx8mm_i2c4_sels[] = {"clock-osc-24m", "sys_pll1_160m", "sys_pll2_50m", "sys_pll3_out", "audio_pll1_out",
 					 "video_pll1_out", "audio_pll2_out", "sys_pll1_133m", };
 
+#ifndef CONFIG_SPL_BUILD
 static const char *imx8mm_pwm1_sels[] = {"clock-osc-24m", "sys_pll2_100m", "sys_pll1_160m", "sys_pll1_40m",
 					 "sys_pll3_out", "clk_ext1", "sys_pll1_80m", "video_pll1_out", };
 
@@ -77,6 +78,7 @@ static const char *imx8mm_pwm3_sels[] = {"clock-osc-24m", "sys_pll2_100m", "sys_
 
 static const char *imx8mm_pwm4_sels[] = {"clock-osc-24m", "sys_pll2_100m", "sys_pll1_160m", "sys_pll1_40m",
 					 "sys_pll3_out", "clk_ext2", "sys_pll1_80m", "video_pll1_out", };
+#endif
 
 static const char *imx8mm_wdog_sels[] = {"clock-osc-24m", "sys_pll1_133m", "sys_pll1_160m", "vpu_pll_out",
 					 "sys_pll2_125m", "sys_pll3_out", "sys_pll1_80m", "sys_pll2_166m", };
@@ -267,14 +269,6 @@ static int imx8mm_clk_probe(struct udevice *dev)
 	       imx8m_clk_composite("i2c3", imx8mm_i2c3_sels, base + 0xae00));
 	clk_dm(IMX8MM_CLK_I2C4,
 	       imx8m_clk_composite("i2c4", imx8mm_i2c4_sels, base + 0xae80));
-	clk_dm(IMX8MM_CLK_PWM1,
-	       imx8m_clk_composite("pwm1", imx8mm_pwm1_sels, base + 0xb380));
-	clk_dm(IMX8MM_CLK_PWM2,
-	       imx8m_clk_composite("pwm2", imx8mm_pwm2_sels, base + 0xb400));
-	clk_dm(IMX8MM_CLK_PWM3,
-	       imx8m_clk_composite("pwm3", imx8mm_pwm3_sels, base + 0xb480));
-	clk_dm(IMX8MM_CLK_PWM4,
-	       imx8m_clk_composite("pwm4", imx8mm_pwm4_sels, base + 0xb500));
 	clk_dm(IMX8MM_CLK_WDOG,
 	       imx8m_clk_composite("wdog", imx8mm_wdog_sels, base + 0xb900));
 	clk_dm(IMX8MM_CLK_USDHC3,
@@ -309,14 +303,6 @@ static int imx8mm_clk_probe(struct udevice *dev)
 	       imx_clk_gate4("i2c4_root_clk", "i2c4", base + 0x41a0, 0));
 	clk_dm(IMX8MM_CLK_OCOTP_ROOT,
 	       imx_clk_gate4("ocotp_root_clk", "ipg_root", base + 0x4220, 0));
-	clk_dm(IMX8MM_CLK_PWM1_ROOT,
-	       imx_clk_gate4("pwm1_root_clk", "pwm1", base + 0x4280, 0));
-	clk_dm(IMX8MM_CLK_PWM2_ROOT,
-	       imx_clk_gate4("pwm2_root_clk", "pwm2", base + 0x4290, 0));
-	clk_dm(IMX8MM_CLK_PWM3_ROOT,
-	       imx_clk_gate4("pwm3_root_clk", "pwm3", base + 0x42a0, 0));
-	clk_dm(IMX8MM_CLK_PWM4_ROOT,
-	       imx_clk_gate4("pwm4_root_clk", "pwm4", base + 0x42b0, 0));
 	clk_dm(IMX8MM_CLK_USDHC1_ROOT,
 	       imx_clk_gate4("usdhc1_root_clk", "usdhc1", base + 0x4510, 0));
 	clk_dm(IMX8MM_CLK_USDHC2_ROOT,
@@ -348,6 +334,22 @@ static int imx8mm_clk_probe(struct udevice *dev)
 	clk_dm(IMX8MM_CLK_ENET1_ROOT,
 	       imx_clk_gate4("enet1_root_clk", "enet_axi",
 	       base + 0x40a0, 0));
+	clk_dm(IMX8MM_CLK_PWM1,
+	       imx8m_clk_composite("pwm1", imx8mm_pwm1_sels, base + 0xb380));
+	clk_dm(IMX8MM_CLK_PWM2,
+	       imx8m_clk_composite("pwm2", imx8mm_pwm2_sels, base + 0xb400));
+	clk_dm(IMX8MM_CLK_PWM3,
+	       imx8m_clk_composite("pwm3", imx8mm_pwm3_sels, base + 0xb480));
+	clk_dm(IMX8MM_CLK_PWM4,
+	       imx8m_clk_composite("pwm4", imx8mm_pwm4_sels, base + 0xb500));
+	clk_dm(IMX8MM_CLK_PWM1_ROOT,
+	       imx_clk_gate4("pwm1_root_clk", "pwm1", base + 0x4280, 0));
+	clk_dm(IMX8MM_CLK_PWM2_ROOT,
+	       imx_clk_gate4("pwm2_root_clk", "pwm2", base + 0x4290, 0));
+	clk_dm(IMX8MM_CLK_PWM3_ROOT,
+	       imx_clk_gate4("pwm3_root_clk", "pwm3", base + 0x42a0, 0));
+	clk_dm(IMX8MM_CLK_PWM4_ROOT,
+	       imx_clk_gate4("pwm4_root_clk", "pwm4", base + 0x42b0, 0));
 #endif
 
 	return 0;
Signature · 1 line
2.25.1
#2 lore raw

PATCH 1/4 clk-imx8mm: Only build PWM clocks in non-SPL code

Quoted 3 lines

PWM is not used inside SPL, so do not define the PWM clocks inside SPL to reduce the final SPL binary size.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#3 lore raw

PATCH 2/4 clk-imx8mm: Move CLK_ENET_AXI to the non-SPL section

In reply to Fabio Estevam

Ethernet is not used inside SPL, so move the IMX8MM_CLK_ENET_AXI clock inside the non-SPL block to reduce the final SPL binary size.

---
 drivers/clk/imx/clk-imx8mm.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/clk/imx/clk-imx8mm.c +4 -4
index 0d7891f11a..286915982c 100644
@@ -28,10 +28,10 @@ static const char *imx8mm_a53_sels[] = {"clock-osc-24m", "arm_pll_out", "sys_pll
 static const char *imx8mm_ahb_sels[] = {"clock-osc-24m", "sys_pll1_133m", "sys_pll1_800m", "sys_pll1_400m",
 					"sys_pll2_125m", "sys_pll3_out", "audio_pll1_out", "video_pll1_out", };
 
+#ifndef CONFIG_SPL_BUILD
 static const char *imx8mm_enet_axi_sels[] = {"clock-osc-24m", "sys_pll1_266m", "sys_pll1_800m", "sys_pll2_250m",
 					     "sys_pll2_200m", "audio_pll1_out", "video_pll1_out", "sys_pll3_out", };
 
-#ifndef CONFIG_SPL_BUILD
 static const char *imx8mm_enet_ref_sels[] = {"clock-osc-24m", "sys_pll2_125m", "sys_pll2_50m", "sys_pll2_100m",
 					     "sys_pll1_160m", "audio_pll1_out", "video_pll1_out", "clk_ext4", };
 
@@ -244,9 +244,6 @@ static int imx8mm_clk_probe(struct udevice *dev)
 	clk_dm(IMX8MM_CLK_IPG_ROOT,
 	       imx_clk_divider2("ipg_root", "ahb", base + 0x9080, 0, 1));
 
-	clk_dm(IMX8MM_CLK_ENET_AXI,
-	       imx8m_clk_composite("enet_axi", imx8mm_enet_axi_sels,
-				   base + 0x8880));
 	clk_dm(IMX8MM_CLK_NAND_USDHC_BUS,
 	       imx8m_clk_composite_critical("nand_usdhc_bus",
 					    imx8mm_nand_usdhc_sels,
@@ -322,6 +319,9 @@ static int imx8mm_clk_probe(struct udevice *dev)
 
 	/* clks not needed in SPL stage */
 #ifndef CONFIG_SPL_BUILD
+	clk_dm(IMX8MM_CLK_ENET_AXI,
+	       imx8m_clk_composite("enet_axi", imx8mm_enet_axi_sels,
+				   base + 0x8880));
 	clk_dm(IMX8MM_CLK_ENET_REF,
 	       imx8m_clk_composite("enet_ref", imx8mm_enet_ref_sels,
 	       base + 0xa980));
Signature · 1 line
2.25.1
#4 lore raw

PATCH 2/4 clk-imx8mm: Move CLK_ENET_AXI to the non-SPL section

Quoted 3 lines

Ethernet is not used inside SPL, so move the IMX8MM_CLK_ENET_AXI clock inside the non-SPL block to reduce the final SPL binary size.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#5 lore raw

PATCH 3/4 clk-imx8mm: Only build ecspi clocks when CONFIG_DM_SPI=y

In reply to Fabio Estevam

The ecspi clocks are only used when CONFIG_DM_SPI=y, so only build the ecspi clocks in this case to reduce the final SPL binary size.

---
 drivers/clk/imx/clk-imx8mm.c | 31 ++++++++++++++++++-------------
 1 file changed, 18 insertions(+), 13 deletions(-)
drivers/clk/imx/clk-imx8mm.c +18 -13
index 286915982c..b6a289b01d 100644
@@ -95,6 +95,7 @@ static const char *imx8mm_usb_core_sels[] = {"clock-osc-24m", "sys_pll1_100m", "
 static const char *imx8mm_usb_phy_sels[] = {"clock-osc-24m", "sys_pll1_100m", "sys_pll1_40m", "sys_pll2_100m",
 					     "sys_pll2_200m", "clk_ext2", "clk_ext3", "audio_pll2_out", };
 
+#if CONFIG_IS_ENABLED(DM_SPI)
 static const char *imx8mm_ecspi1_sels[] = {"clock-osc-24m", "sys_pll2_200m", "sys_pll1_40m", "sys_pll1_160m",
 					   "sys_pll1_800m", "sys_pll3_out", "sys_pll2_250m", "audio_pll2_out", };
 
@@ -103,6 +104,7 @@ static const char *imx8mm_ecspi2_sels[] = {"clock-osc-24m", "sys_pll2_200m", "sy
 
 static const char *imx8mm_ecspi3_sels[] = {"clock-osc-24m", "sys_pll2_200m", "sys_pll1_40m", "sys_pll1_160m",
 					   "sys_pll1_800m", "sys_pll3_out", "sys_pll2_250m", "audio_pll2_out", };
+#endif
 
 static int imx8mm_clk_probe(struct udevice *dev)
 {
@@ -277,19 +279,6 @@ static int imx8mm_clk_probe(struct udevice *dev)
 		imx8m_clk_composite("usb_core_ref", imx8mm_usb_core_sels, base + 0xb100));
 	clk_dm(IMX8MM_CLK_USB_PHY_REF,
 		imx8m_clk_composite("usb_phy_ref", imx8mm_usb_phy_sels, base + 0xb180));
-	clk_dm(IMX8MM_CLK_ECSPI1,
-	       imx8m_clk_composite("ecspi1", imx8mm_ecspi1_sels, base + 0xb280));
-	clk_dm(IMX8MM_CLK_ECSPI2,
-	       imx8m_clk_composite("ecspi2", imx8mm_ecspi2_sels, base + 0xb300));
-	clk_dm(IMX8MM_CLK_ECSPI3,
-	       imx8m_clk_composite("ecspi3", imx8mm_ecspi3_sels, base + 0xc180));
-
-	clk_dm(IMX8MM_CLK_ECSPI1_ROOT,
-	       imx_clk_gate4("ecspi1_root_clk", "ecspi1", base + 0x4070, 0));
-	clk_dm(IMX8MM_CLK_ECSPI2_ROOT,
-	       imx_clk_gate4("ecspi2_root_clk", "ecspi2", base + 0x4080, 0));
-	clk_dm(IMX8MM_CLK_ECSPI3_ROOT,
-	       imx_clk_gate4("ecspi3_root_clk", "ecspi3", base + 0x4090, 0));
 	clk_dm(IMX8MM_CLK_I2C1_ROOT,
 	       imx_clk_gate4("i2c1_root_clk", "i2c1", base + 0x4170, 0));
 	clk_dm(IMX8MM_CLK_I2C2_ROOT,
@@ -352,6 +341,22 @@ static int imx8mm_clk_probe(struct udevice *dev)
 	       imx_clk_gate4("pwm4_root_clk", "pwm4", base + 0x42b0, 0));
 #endif
 
+#if CONFIG_IS_ENABLED(DM_SPI)
+	clk_dm(IMX8MM_CLK_ECSPI1,
+	       imx8m_clk_composite("ecspi1", imx8mm_ecspi1_sels, base + 0xb280));
+	clk_dm(IMX8MM_CLK_ECSPI2,
+	       imx8m_clk_composite("ecspi2", imx8mm_ecspi2_sels, base + 0xb300));
+	clk_dm(IMX8MM_CLK_ECSPI3,
+	       imx8m_clk_composite("ecspi3", imx8mm_ecspi3_sels, base + 0xc180));
+
+	clk_dm(IMX8MM_CLK_ECSPI1_ROOT,
+	       imx_clk_gate4("ecspi1_root_clk", "ecspi1", base + 0x4070, 0));
+	clk_dm(IMX8MM_CLK_ECSPI2_ROOT,
+	       imx_clk_gate4("ecspi2_root_clk", "ecspi2", base + 0x4080, 0));
+	clk_dm(IMX8MM_CLK_ECSPI3_ROOT,
+	       imx_clk_gate4("ecspi3_root_clk", "ecspi3", base + 0x4090, 0));
+#endif
+
 	return 0;
 }
 
Signature · 1 line
2.25.1
#6 lore raw

PATCH 3/4 clk-imx8mm: Only build ecspi clocks when CONFIG_DM_SPI=y

Quoted 3 lines

The ecspi clocks are only used when CONFIG_DM_SPI=y, so only build the ecspi clocks in this case to reduce the final SPL binary size.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#7 lore raw

PATCH 4/4 clk-imx8mm: Only build QSPI clocks when CONFIG_NXP_FSPI=y

In reply to Fabio Estevam

The QSPI clocks are only used when CONFIG_NXP_FSPI=y, so only build the QSPI clocks in this case to reduce the final SPL binary size.

---
 drivers/clk/imx/clk-imx8mm.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)
drivers/clk/imx/clk-imx8mm.c +9 -4
index b6a289b01d..b5c253e496 100644
@@ -86,8 +86,10 @@ static const char *imx8mm_wdog_sels[] = {"clock-osc-24m", "sys_pll1_133m", "sys_
 static const char *imx8mm_usdhc3_sels[] = {"clock-osc-24m", "sys_pll1_400m", "sys_pll1_800m", "sys_pll2_500m",
 					   "sys_pll3_out", "sys_pll1_266m", "audio_pll2_clk", "sys_pll1_100m", };
 
+#if CONFIG_IS_ENABLED(NXP_FSPI)
 static const char *imx8mm_qspi_sels[] = {"clock-osc-24m", "sys_pll1_400m", "sys_pll2_333m", "sys_pll2_500m",
 					   "audio_pll2_out", "sys_pll1_266m", "sys_pll3_out", "sys_pll1_100m", };
+#endif
 
 static const char *imx8mm_usb_core_sels[] = {"clock-osc-24m", "sys_pll1_100m", "sys_pll1_40m", "sys_pll2_100m",
 					     "sys_pll2_200m", "clk_ext2", "clk_ext3", "audio_pll2_out", };
@@ -273,8 +275,6 @@ static int imx8mm_clk_probe(struct udevice *dev)
 	clk_dm(IMX8MM_CLK_USDHC3,
 	       imx8m_clk_composite("usdhc3", imx8mm_usdhc3_sels,
 				   base + 0xbc80));
-	clk_dm(IMX8MM_CLK_QSPI,
-	       imx8m_clk_composite("qspi", imx8mm_qspi_sels, base + 0xab80));
 	clk_dm(IMX8MM_CLK_USB_CORE_REF,
 		imx8m_clk_composite("usb_core_ref", imx8mm_usb_core_sels, base + 0xb100));
 	clk_dm(IMX8MM_CLK_USB_PHY_REF,
@@ -301,8 +301,6 @@ static int imx8mm_clk_probe(struct udevice *dev)
 	       imx_clk_gate4("wdog3_root_clk", "wdog", base + 0x4550, 0));
 	clk_dm(IMX8MM_CLK_USDHC3_ROOT,
 	       imx_clk_gate4("usdhc3_root_clk", "usdhc3", base + 0x45e0, 0));
-	clk_dm(IMX8MM_CLK_QSPI_ROOT,
-	       imx_clk_gate4("qspi_root_clk", "qspi", base + 0x42f0, 0));
 	clk_dm(IMX8MM_CLK_USB1_CTRL_ROOT,
 		imx_clk_gate4("usb1_ctrl_root_clk", "usb_bus", base + 0x44d0, 0));
 
@@ -357,6 +355,13 @@ static int imx8mm_clk_probe(struct udevice *dev)
 	       imx_clk_gate4("ecspi3_root_clk", "ecspi3", base + 0x4090, 0));
 #endif
 
+#if CONFIG_IS_ENABLED(NXP_FSPI)
+	clk_dm(IMX8MM_CLK_QSPI,
+	       imx8m_clk_composite("qspi", imx8mm_qspi_sels, base + 0xab80));
+	clk_dm(IMX8MM_CLK_QSPI_ROOT,
+	       imx_clk_gate4("qspi_root_clk", "qspi", base + 0x42f0, 0));
+#endif
+
 	return 0;
 }
 
Signature · 1 line
2.25.1
#8 lore raw

PATCH 4/4 clk-imx8mm: Only build QSPI clocks when CONFIG_NXP_FSPI=y

Quoted 3 lines

The QSPI clocks are only used when CONFIG_NXP_FSPI=y, so only build the QSPI clocks in this case to reduce the final SPL binary size.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#9 lore raw
In reply to Fabio Estevam

Hi Fabio

Quoted 15 lines · Fabio Estevam

Reduce the SPL binary size by building some clocks only for the non-SPL case, such as Ethernet and PWM and by also building ECSPI and QSPI when their respective drivers are enabled.

On a imx8mm_evk_defconfig the following SPL binary reduction was observed.

Prior to this series:

$ aarch64-linux-gnu-readelf -s spl/u-boot-spl | sort -nk 3 | grep imx8mm_clk_probe
   766: 00000000007f34c8  4100 FUNC    LOCAL  DEFAULT    1 imx8mm_clk_probe

After this series:

Quoted 8 lines
$ aarch64-linux-gnu-readelf -s spl/u-boot-spl | sort -nk 3 | grep imx8mm_clk_probe
   766: 00000000007f34c8  3316 FUNC    LOCAL  DEFAULT    1 imx8mm_clk_probe

Total reduction: 4100 - 3316 = 784 bytes.

Fabio Estevam (4):
clk-imx8mm: Only build PWM clocks in non-SPL code
clk-imx8mm: Move CLK_ENET_AXI to the non-SPL section

I'm not really convinced of those two. I mean with should maybe think about some different approach of clock framework to reduce the size

Michael

Quoted 9 lines

clk-imx8mm: Only build ecspi clocks when CONFIG_DM_SPI=y
clk-imx8mm: Only build QSPI clocks when CONFIG_NXP_FSPI=y

 drivers/clk/imx/clk-imx8mm.c | 86 ++++++++++++++++++++----------------
 1 file changed, 49 insertions(+), 37 deletions(-)

--
2.25.1

Signature · 11 lines
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
[email protected]
__________________________________

Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
[email protected]
www.amarulasolutions.com
#10 lore raw

Hi Michael,

Quoted 6 lines · Michael Nazzareno Trimarchi
Quoted 3 lines

Fabio Estevam (4):
clk-imx8mm: Only build PWM clocks in non-SPL code
clk-imx8mm: Move CLK_ENET_AXI to the non-SPL section

I'm not really convinced of those two. I mean with should maybe think about some different approach of clock framework to reduce the size

What is your proposal then?

#11 lore raw

Hi Fabio

Quoted 9 lines · Fabio Estevam

Hi Michael,

Quoted 4 lines · Michael Nazzareno Trimarchi
Quoted 3 lines

Fabio Estevam (4):
clk-imx8mm: Only build PWM clocks in non-SPL code
clk-imx8mm: Move CLK_ENET_AXI to the non-SPL section

Quoted 5 lines
Quoted 3 lines

I'm not really convinced of those two. I mean with should maybe think about
some different approach of clock framework to reduce the size

What is your proposal then?

When Dario wrote the Ti clock, he was using the dtsi. One idea can be understand if this approch
cost less in term of space in the SPL

Michael

Signature · 11 lines
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
[email protected]
__________________________________

Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
[email protected]
www.amarulasolutions.com
reviewer
#12 lore raw

Hi Michael,

Quoted 3 lines · Michael Nazzareno Trimarchi

When Dario wrote the Ti clock, he was using the dtsi. One idea can be understand if this approch
cost less in term of space in the SPL

Care to submit a patch series with your proposal?

#13 lore raw

Hi Fabio

Quoted 11 lines · Fabio Estevam

Hi Michael,

Quoted 3 lines · Michael Nazzareno Trimarchi

When Dario wrote the Ti clock, he was using the dtsi. One idea can be understand if this approch
cost less in term of space in the SPL

Care to submit a patch series with your proposal?

Our plan can be this one. We are soon sending some patches for imx Nand subsystems that introduce new clocks there. We use then this series
to create a PoC where we move those clocks in dtsi format as in omap and then send it later

Michael

Signature · 11 lines
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
[email protected]
__________________________________

Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
[email protected]
www.amarulasolutions.com