clk-imx8mm: Reduce SPL binary size
Subsystems (3)
cover clk-imx8mm: Reduce SPL binary size
Reduce the SPL binary size by building some clocks only for the non-SPL case, such as Ethernet and PWM and by also building ECSPI and QSPI when their respective drivers are enabled.
On a imx8mm_evk_defconfig the following SPL binary reduction was observed.
Prior to this series:
$ aarch64-linux-gnu-readelf -s spl/u-boot-spl | sort -nk 3 | grep imx8mm_clk_probe 766: 00000000007f34c8 4100 FUNC LOCAL DEFAULT 1 imx8mm_clk_probe
After this series:
$ aarch64-linux-gnu-readelf -s spl/u-boot-spl | sort -nk 3 | grep imx8mm_clk_probe 766: 00000000007f34c8 3316 FUNC LOCAL DEFAULT 1 imx8mm_clk_probe
Total reduction: 4100 - 3316 = 784 bytes.
Fabio Estevam (4):
clk-imx8mm: Only build PWM clocks in non-SPL code
clk-imx8mm: Move CLK_ENET_AXI to the non-SPL section
clk-imx8mm: Only build ecspi clocks when CONFIG_DM_SPI=y
clk-imx8mm: Only build QSPI clocks when CONFIG_NXP_FSPI=y
drivers/clk/imx/clk-imx8mm.c | 86 ++++++++++++++++++++---------------- 1 file changed, 49 insertions(+), 37 deletions(-)
Signature · 1 line
2.25.1
PATCH 1/4 clk-imx8mm: Only build PWM clocks in non-SPL code
PWM is not used inside SPL, so do not define the PWM clocks inside SPL to reduce the final SPL binary size.
--- drivers/clk/imx/clk-imx8mm.c | 34 ++++++++++++++++++---------------- 1 file changed, 18 insertions(+), 16 deletions(-)
drivers/clk/imx/clk-imx8mm.c +18 -16
@@ -66,6 +66,7 @@ static const char *imx8mm_i2c3_sels[] = {"clock-osc-24m", "sys_pll1_160m", "sys_static const char *imx8mm_i2c4_sels[] = {"clock-osc-24m" ,"sys_pll1_160m" ,"sys_pll2_50m" ,"sys_pll3_out" ,"audio_pll1_out" ,"video_pll1_out" ,"audio_pll2_out" ,"sys_pll1_133m" , }; +#ifndef CONFIG_SPL_BUILD static const char *imx8mm_pwm1_sels[] = {"clock-osc-24m" ,"sys_pll2_100m" ,"sys_pll1_160m" ,"sys_pll1_40m" ,"sys_pll3_out" ,"clk_ext1" ,"sys_pll1_80m" ,"video_pll1_out" , };
@@ -77,6 +78,7 @@ static const char *imx8mm_pwm3_sels[] = {"clock-osc-24m", "sys_pll2_100m", "sys_static const char *imx8mm_pwm4_sels[] = {"clock-osc-24m" ,"sys_pll2_100m" ,"sys_pll1_160m" ,"sys_pll1_40m" ,"sys_pll3_out" ,"clk_ext2" ,"sys_pll1_80m" ,"video_pll1_out" , }; +#endif static const char *imx8mm_wdog_sels[] = {"clock-osc-24m" ,"sys_pll1_133m" ,"sys_pll1_160m" ,"vpu_pll_out" ,"sys_pll2_125m" ,"sys_pll3_out" ,"sys_pll1_80m" ,"sys_pll2_166m" , };
@@ -267,14 +269,6 @@ static int imx8mm_clk_probe(struct udevice *dev) imx8m_clk_composite("i2c3", imx8mm_i2c3_sels, base + 0xae00));clk_dm (IMX8MM_CLK_I2C4 ,imx8m_clk_composite ("i2c4" , imx8mm_i2c4_sels, base +0xae80 )); -clk_dm (IMX8MM_CLK_PWM1 , -imx8m_clk_composite ("pwm1" , imx8mm_pwm1_sels, base +0xb380 )); -clk_dm (IMX8MM_CLK_PWM2 , -imx8m_clk_composite ("pwm2" , imx8mm_pwm2_sels, base +0xb400 )); -clk_dm (IMX8MM_CLK_PWM3 , -imx8m_clk_composite ("pwm3" , imx8mm_pwm3_sels, base +0xb480 )); -clk_dm (IMX8MM_CLK_PWM4 , -imx8m_clk_composite ("pwm4" , imx8mm_pwm4_sels, base +0xb500 ));clk_dm (IMX8MM_CLK_WDOG ,imx8m_clk_composite ("wdog" , imx8mm_wdog_sels, base +0xb900 )); clk_dm(IMX8MM_CLK_USDHC3,
@@ -309,14 +303,6 @@ static int imx8mm_clk_probe(struct udevice *dev) imx_clk_gate4("i2c4_root_clk", "i2c4", base + 0x41a0, 0));clk_dm (IMX8MM_CLK_OCOTP_ROOT ,imx_clk_gate4 ("ocotp_root_clk" ,"ipg_root" , base +0x4220 ,0 )); -clk_dm (IMX8MM_CLK_PWM1_ROOT , -imx_clk_gate4 ("pwm1_root_clk" ,"pwm1" , base +0x4280 ,0 )); -clk_dm (IMX8MM_CLK_PWM2_ROOT , -imx_clk_gate4 ("pwm2_root_clk" ,"pwm2" , base +0x4290 ,0 )); -clk_dm (IMX8MM_CLK_PWM3_ROOT , -imx_clk_gate4 ("pwm3_root_clk" ,"pwm3" , base +0x42a0 ,0 )); -clk_dm (IMX8MM_CLK_PWM4_ROOT , -imx_clk_gate4 ("pwm4_root_clk" ,"pwm4" , base +0x42b0 ,0 ));clk_dm (IMX8MM_CLK_USDHC1_ROOT ,imx_clk_gate4 ("usdhc1_root_clk" ,"usdhc1" , base +0x4510 ,0 )); clk_dm(IMX8MM_CLK_USDHC2_ROOT,
@@ -348,6 +334,22 @@ static int imx8mm_clk_probe(struct udevice *dev)clk_dm (IMX8MM_CLK_ENET1_ROOT ,imx_clk_gate4 ("enet1_root_clk" ,"enet_axi" , base +0x40a0 ,0 )); +clk_dm (IMX8MM_CLK_PWM1 , +imx8m_clk_composite ("pwm1" , imx8mm_pwm1_sels, base +0xb380 )); +clk_dm (IMX8MM_CLK_PWM2 , +imx8m_clk_composite ("pwm2" , imx8mm_pwm2_sels, base +0xb400 )); +clk_dm (IMX8MM_CLK_PWM3 , +imx8m_clk_composite ("pwm3" , imx8mm_pwm3_sels, base +0xb480 )); +clk_dm (IMX8MM_CLK_PWM4 , +imx8m_clk_composite ("pwm4" , imx8mm_pwm4_sels, base +0xb500 )); +clk_dm (IMX8MM_CLK_PWM1_ROOT , +imx_clk_gate4 ("pwm1_root_clk" ,"pwm1" , base +0x4280 ,0 )); +clk_dm (IMX8MM_CLK_PWM2_ROOT , +imx_clk_gate4 ("pwm2_root_clk" ,"pwm2" , base +0x4290 ,0 )); +clk_dm (IMX8MM_CLK_PWM3_ROOT , +imx_clk_gate4 ("pwm3_root_clk" ,"pwm3" , base +0x42a0 ,0 )); +clk_dm (IMX8MM_CLK_PWM4_ROOT , +imx_clk_gate4 ("pwm4_root_clk" ,"pwm4" , base +0x42b0 ,0 ));#endif return 0 ;
Signature · 1 line
2.25.1
PATCH 1/4 clk-imx8mm: Only build PWM clocks in non-SPL code
Quoted 3 lines
PWM is not used inside SPL, so do not define the PWM clocks inside SPL to reduce the final SPL binary size.
Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 2/4 clk-imx8mm: Move CLK_ENET_AXI to the non-SPL section
In reply to Fabio EstevamEthernet is not used inside SPL, so move the IMX8MM_CLK_ENET_AXI clock inside the non-SPL block to reduce the final SPL binary size.
--- drivers/clk/imx/clk-imx8mm.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/clk/imx/clk-imx8mm.c +4 -4
@@ -28,10 +28,10 @@ static const char *imx8mm_a53_sels[] = {"clock-osc-24m", "arm_pll_out", "sys_pllstatic const char *imx8mm_ahb_sels[] = {"clock-osc-24m" ,"sys_pll1_133m" ,"sys_pll1_800m" ,"sys_pll1_400m" ,"sys_pll2_125m" ,"sys_pll3_out" ,"audio_pll1_out" ,"video_pll1_out" , }; +#ifndef CONFIG_SPL_BUILD static const char *imx8mm_enet_axi_sels[] = {"clock-osc-24m" ,"sys_pll1_266m" ,"sys_pll1_800m" ,"sys_pll2_250m" ,"sys_pll2_200m" ,"audio_pll1_out" ,"video_pll1_out" ,"sys_pll3_out" , }; -#ifndef CONFIG_SPL_BUILD static const char *imx8mm_enet_ref_sels[] = {"clock-osc-24m" ,"sys_pll2_125m" ,"sys_pll2_50m" ,"sys_pll2_100m" ,"sys_pll1_160m" ,"audio_pll1_out" ,"video_pll1_out" ,"clk_ext4" , };
@@ -244,9 +244,6 @@ static int imx8mm_clk_probe(struct udevice *dev)clk_dm (IMX8MM_CLK_IPG_ROOT ,imx_clk_divider2 ("ipg_root" ,"ahb" , base +0x9080 ,0 ,1 )); -clk_dm (IMX8MM_CLK_ENET_AXI , -imx8m_clk_composite ("enet_axi" , imx8mm_enet_axi_sels, - base +0x8880 )); clk_dm(IMX8MM_CLK_NAND_USDHC_BUS, imx8m_clk_composite_critical("nand_usdhc_bus", imx8mm_nand_usdhc_sels,
@@ -322,6 +319,9 @@ static int imx8mm_clk_probe(struct udevice *dev)/* clks not needed in SPL stage */ #ifndef CONFIG_SPL_BUILD +clk_dm (IMX8MM_CLK_ENET_AXI , +imx8m_clk_composite ("enet_axi" , imx8mm_enet_axi_sels, + base +0x8880 ));clk_dm (IMX8MM_CLK_ENET_REF ,imx8m_clk_composite ("enet_ref" , imx8mm_enet_ref_sels, base +0xa980 ));
Signature · 1 line
2.25.1
PATCH 2/4 clk-imx8mm: Move CLK_ENET_AXI to the non-SPL section
Quoted 3 lines
Ethernet is not used inside SPL, so move the
IMX8MM_CLK_ENET_AXIclock inside the non-SPL block to reduce the final SPL binary size.Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 3/4 clk-imx8mm: Only build ecspi clocks when CONFIG_DM_SPI=y
In reply to Fabio EstevamThe ecspi clocks are only used when CONFIG_DM_SPI=y, so only build the ecspi clocks in this case to reduce the final SPL binary size.
--- drivers/clk/imx/clk-imx8mm.c | 31 ++++++++++++++++++------------- 1 file changed, 18 insertions(+), 13 deletions(-)
drivers/clk/imx/clk-imx8mm.c +18 -13
@@ -95,6 +95,7 @@ static const char *imx8mm_usb_core_sels[] = {"clock-osc-24m", "sys_pll1_100m", "static const char *imx8mm_usb_phy_sels[] = {"clock-osc-24m" ,"sys_pll1_100m" ,"sys_pll1_40m" ,"sys_pll2_100m" ,"sys_pll2_200m" ,"clk_ext2" ,"clk_ext3" ,"audio_pll2_out" , }; +#if CONFIG_IS_ENABLED (DM_SPI )static const char *imx8mm_ecspi1_sels[] = {"clock-osc-24m" ,"sys_pll2_200m" ,"sys_pll1_40m" ,"sys_pll1_160m" ,"sys_pll1_800m" ,"sys_pll3_out" ,"sys_pll2_250m" ,"audio_pll2_out" , };
@@ -103,6 +104,7 @@ static const char *imx8mm_ecspi2_sels[] = {"clock-osc-24m", "sys_pll2_200m", "systatic const char *imx8mm_ecspi3_sels[] = {"clock-osc-24m" ,"sys_pll2_200m" ,"sys_pll1_40m" ,"sys_pll1_160m" ,"sys_pll1_800m" ,"sys_pll3_out" ,"sys_pll2_250m" ,"audio_pll2_out" , }; +#endif static int imx8mm_clk_probe (struct udevice *dev) {
@@ -277,19 +279,6 @@ static int imx8mm_clk_probe(struct udevice *dev) imx8m_clk_composite("usb_core_ref", imx8mm_usb_core_sels, base + 0xb100));clk_dm (IMX8MM_CLK_USB_PHY_REF ,imx8m_clk_composite ("usb_phy_ref" , imx8mm_usb_phy_sels, base +0xb180 )); -clk_dm (IMX8MM_CLK_ECSPI1 , -imx8m_clk_composite ("ecspi1" , imx8mm_ecspi1_sels, base +0xb280 )); -clk_dm (IMX8MM_CLK_ECSPI2 , -imx8m_clk_composite ("ecspi2" , imx8mm_ecspi2_sels, base +0xb300 )); -clk_dm (IMX8MM_CLK_ECSPI3 , -imx8m_clk_composite ("ecspi3" , imx8mm_ecspi3_sels, base +0xc180 )); - -clk_dm (IMX8MM_CLK_ECSPI1_ROOT , -imx_clk_gate4 ("ecspi1_root_clk" ,"ecspi1" , base +0x4070 ,0 )); -clk_dm (IMX8MM_CLK_ECSPI2_ROOT , -imx_clk_gate4 ("ecspi2_root_clk" ,"ecspi2" , base +0x4080 ,0 )); -clk_dm (IMX8MM_CLK_ECSPI3_ROOT , -imx_clk_gate4 ("ecspi3_root_clk" ,"ecspi3" , base +0x4090 ,0 ));clk_dm (IMX8MM_CLK_I2C1_ROOT ,imx_clk_gate4 ("i2c1_root_clk" ,"i2c1" , base +0x4170 ,0 )); clk_dm(IMX8MM_CLK_I2C2_ROOT,
@@ -352,6 +341,22 @@ static int imx8mm_clk_probe(struct udevice *dev) imx_clk_gate4("pwm4_root_clk", "pwm4", base + 0x42b0, 0));#endif +#if CONFIG_IS_ENABLED (DM_SPI ) +clk_dm (IMX8MM_CLK_ECSPI1 , +imx8m_clk_composite ("ecspi1" , imx8mm_ecspi1_sels, base +0xb280 )); +clk_dm (IMX8MM_CLK_ECSPI2 , +imx8m_clk_composite ("ecspi2" , imx8mm_ecspi2_sels, base +0xb300 )); +clk_dm (IMX8MM_CLK_ECSPI3 , +imx8m_clk_composite ("ecspi3" , imx8mm_ecspi3_sels, base +0xc180 )); + +clk_dm (IMX8MM_CLK_ECSPI1_ROOT , +imx_clk_gate4 ("ecspi1_root_clk" ,"ecspi1" , base +0x4070 ,0 )); +clk_dm (IMX8MM_CLK_ECSPI2_ROOT , +imx_clk_gate4 ("ecspi2_root_clk" ,"ecspi2" , base +0x4080 ,0 )); +clk_dm (IMX8MM_CLK_ECSPI3_ROOT , +imx_clk_gate4 ("ecspi3_root_clk" ,"ecspi3" , base +0x4090 ,0 )); +#endif +return 0 ; }
Signature · 1 line
2.25.1
PATCH 3/4 clk-imx8mm: Only build ecspi clocks when CONFIG_DM_SPI=y
Quoted 3 lines
The ecspi clocks are only used when
CONFIG_DM_SPI=y, so only build the ecspi clocks in this case to reduce the final SPL binary size.Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 4/4 clk-imx8mm: Only build QSPI clocks when CONFIG_NXP_FSPI=y
In reply to Fabio EstevamThe QSPI clocks are only used when CONFIG_NXP_FSPI=y, so only build the QSPI clocks in this case to reduce the final SPL binary size.
--- drivers/clk/imx/clk-imx8mm.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-)
drivers/clk/imx/clk-imx8mm.c +9 -4
@@ -86,8 +86,10 @@ static const char *imx8mm_wdog_sels[] = {"clock-osc-24m", "sys_pll1_133m", "sys_static const char *imx8mm_usdhc3_sels[] = {"clock-osc-24m" ,"sys_pll1_400m" ,"sys_pll1_800m" ,"sys_pll2_500m" ,"sys_pll3_out" ,"sys_pll1_266m" ,"audio_pll2_clk" ,"sys_pll1_100m" , }; +#if CONFIG_IS_ENABLED (NXP_FSPI )static const char *imx8mm_qspi_sels[] = {"clock-osc-24m" ,"sys_pll1_400m" ,"sys_pll2_333m" ,"sys_pll2_500m" ,"audio_pll2_out" ,"sys_pll1_266m" ,"sys_pll3_out" ,"sys_pll1_100m" , }; +#endif static const char *imx8mm_usb_core_sels[] = {"clock-osc-24m" ,"sys_pll1_100m" ,"sys_pll1_40m" ,"sys_pll2_100m" ,"sys_pll2_200m" ,"clk_ext2" ,"clk_ext3" ,"audio_pll2_out" , };
@@ -273,8 +275,6 @@ static int imx8mm_clk_probe(struct udevice *dev)clk_dm (IMX8MM_CLK_USDHC3 ,imx8m_clk_composite ("usdhc3" , imx8mm_usdhc3_sels, base +0xbc80 )); -clk_dm (IMX8MM_CLK_QSPI , -imx8m_clk_composite ("qspi" , imx8mm_qspi_sels, base +0xab80 ));clk_dm (IMX8MM_CLK_USB_CORE_REF ,imx8m_clk_composite ("usb_core_ref" , imx8mm_usb_core_sels, base +0xb100 )); clk_dm(IMX8MM_CLK_USB_PHY_REF,
@@ -301,8 +301,6 @@ static int imx8mm_clk_probe(struct udevice *dev) imx_clk_gate4("wdog3_root_clk", "wdog", base + 0x4550, 0));clk_dm (IMX8MM_CLK_USDHC3_ROOT ,imx_clk_gate4 ("usdhc3_root_clk" ,"usdhc3" , base +0x45e0 ,0 )); -clk_dm (IMX8MM_CLK_QSPI_ROOT , -imx_clk_gate4 ("qspi_root_clk" ,"qspi" , base +0x42f0 ,0 ));clk_dm (IMX8MM_CLK_USB1_CTRL_ROOT ,imx_clk_gate4 ("usb1_ctrl_root_clk" ,"usb_bus" , base +0x44d0 ,0 ));
@@ -357,6 +355,13 @@ static int imx8mm_clk_probe(struct udevice *dev) imx_clk_gate4("ecspi3_root_clk", "ecspi3", base + 0x4090, 0));#endif +#if CONFIG_IS_ENABLED (NXP_FSPI ) +clk_dm (IMX8MM_CLK_QSPI , +imx8m_clk_composite ("qspi" , imx8mm_qspi_sels, base +0xab80 )); +clk_dm (IMX8MM_CLK_QSPI_ROOT , +imx_clk_gate4 ("qspi_root_clk" ,"qspi" , base +0x42f0 ,0 )); +#endif +return 0 ; }
Signature · 1 line
2.25.1
PATCH 4/4 clk-imx8mm: Only build QSPI clocks when CONFIG_NXP_FSPI=y
Quoted 3 lines
The QSPI clocks are only used when
CONFIG_NXP_FSPI=y, so only build the QSPI clocks in this case to reduce the final SPL binary size.Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Hi Fabio
Quoted 15 lines · Fabio Estevam
Reduce the SPL binary size by building some clocks only for the non-SPL case, such as Ethernet and PWM and by also building ECSPI and QSPI when their respective drivers are enabled.
On a
imx8mm_evk_defconfigthe following SPL binary reduction was observed.Prior to this series:
$ aarch64-linux-gnu-readelf -s spl/u-boot-spl | sort -nk 3 | grep imx8mm_clk_probe 766: 00000000007f34c8 4100 FUNC LOCAL DEFAULT 1 imx8mm_clk_probeAfter this series:
Quoted 8 lines
$ aarch64-linux-gnu-readelf -s spl/u-boot-spl | sort -nk 3 | grep imx8mm_clk_probe 766: 00000000007f34c8 3316 FUNC LOCAL DEFAULT 1 imx8mm_clk_probeTotal reduction: 4100 - 3316 = 784 bytes.
Fabio Estevam (4):
clk-imx8mm: Only build PWM clocks in non-SPL code
clk-imx8mm: MoveCLK_ENET_AXIto the non-SPL section
I'm not really convinced of those two. I mean with should maybe think about some different approach of clock framework to reduce the size
Michael
Quoted 9 lines
clk-imx8mm: Only build ecspi clocks when
CONFIG_DM_SPI=y
clk-imx8mm: Only build QSPI clocks whenCONFIG_NXP_FSPI=ydrivers/clk/imx/clk-imx8mm.c | 86 ++++++++++++++++++++---------------- 1 file changed, 49 insertions(+), 37 deletions(-)--
2.25.1
Signature · 11 lines
Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 [email protected] __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 [email protected] www.amarulasolutions.com
Hi Michael,
Quoted 6 lines · Michael Nazzareno Trimarchi
Quoted 3 lines
Fabio Estevam (4):
clk-imx8mm: Only build PWM clocks in non-SPL code
clk-imx8mm: MoveCLK_ENET_AXIto the non-SPL sectionI'm not really convinced of those two. I mean with should maybe think about some different approach of clock framework to reduce the size
What is your proposal then?
Hi Fabio
Quoted 9 lines · Fabio Estevam
Hi Michael,
Quoted 4 lines · Michael Nazzareno Trimarchi
Quoted 3 lines
Fabio Estevam (4):
clk-imx8mm: Only build PWM clocks in non-SPL code
clk-imx8mm: MoveCLK_ENET_AXIto the non-SPL section
Quoted 5 lines
Quoted 3 lines
I'm not really convinced of those two. I mean with should maybe think about
some different approach of clock framework to reduce the sizeWhat is your proposal then?
When Dario wrote the Ti clock, he was using the dtsi. One idea can be understand if this approch
cost less in term of space in the SPL
Michael
Signature · 11 lines
Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 [email protected] __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 [email protected] www.amarulasolutions.com
Fabio Estevam
reviewerHi Michael,
Quoted 3 lines · Michael Nazzareno Trimarchi
When Dario wrote the Ti clock, he was using the dtsi. One idea can be understand if this approch
cost less in term of space in the SPL
Care to submit a patch series with your proposal?
Hi Fabio
Quoted 11 lines · Fabio Estevam
Hi Michael,
Quoted 3 lines · Michael Nazzareno Trimarchi
When Dario wrote the Ti clock, he was using the dtsi. One idea can be understand if this approch
cost less in term of space in the SPLCare to submit a patch series with your proposal?
Our plan can be this one. We are soon sending some patches for imx Nand subsystems that introduce new clocks there. We use then this series
to create a PoC where we move those clocks in dtsi format as in omap and then send it later
Michael
Signature · 11 lines
Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 [email protected] __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 [email protected] www.amarulasolutions.com